3Com 4226T, 4228G, 4250T manual Introducing the Superstack 3 Switch 4200 Series

Page 14

14CHAPTER 1: INTRODUCING THE SUPERSTACK 3 SWITCH 4200 SERIES

WARNING: RJ-45 Ports. These are shielded RJ-45 data sockets. They cannot be used as standard traditional telephone sockets, or to connect the unit to a traditional PBX or public telephone network. Only connect RJ-45 data connectors, network telephony systems, or network telephones to these sockets.

Either shielded or unshielded data cables with shielded or unshielded jacks can be connected to these data sockets.

10BASE-T/The Switch has 24 or 48 auto-negotiating 10BASE-T/100BASE-TX ports 100BASE-TX Ports configured as Auto MDIX (cross-over). While auto-negotiation is enabled,

these ports can automatically detect whether they need to operate in MDI or MDIX mode. Alternatively, you can manually set these ports to 10BASE-T half duplex, 10BASE-T full duplex, 100BASE-TX half duplex or 100BASE-TX full duplex. The maximum segment length is 100 m (328 ft) over Category 5 twisted pair cable.

10/100/1000BASE-TThe Switch has two auto-negotiating 10/100/1000BASE-T ports

Ports configured as Auto MDIX (cross-over). While auto-negotiation is enabled, these ports can automatically detect whether they need to operate in MDI or MDIX mode. These ports provide 10/100/1000 Mbps full duplex connections to other Gigabit Ethernet devices. Full duplex allows packets to be transmitted and received simultaneously which, in effect, doubles the potential throughput of a link. These ports require either straight-through or cross-over Category 5 cables with RJ-45 connectors at both ends. The maximum UTP cable length is 100 m (328 ft) over Category 5 cable.

The 10/100/1000BASE-T ports will auto-negotiate to the appropriate speed.

GBIC Ports This section applies to the SuperStack 3 Switch 4228G only.

The two GBIC ports support Category 5 twisted pair cable and fiber Gigabit Ethernet short-wave (SX), long-wave (LX) and long-haul (LH70) GBIC transceivers in any combination. This offers you the flexibility of using GBIC transceivers to provide connectivity between the Switch and remote 1000 Mbps workgroups or to create a high capacity aggregated link backbone connection.

Page 13 Page 15
Image 14
Page 13 Page 15
Contents SuperStack 3Com Corporation 350 Campus Drive Marlborough, MA United States Government LegendContents Setting UP for Management Safety Information PIN -OUTSPage About this Guide Convention Description ConventionsIcon Description Related DocumentationAbout this Guide Introducing About the Switch FamilySwitch 4200 Family Front View DetailIntroducing the Superstack 3 Switch 4200 Series Color Indicates Port Status LEDs 10BASE-T/100BASE-TX ports Fiber GBICs1000BASE-T GBICs Port Status LEDs Gbic portsUnit LEDs Power/Self Test LEDColor Indicates Alert LEDSystem RPS. See Connecting a Redundant Power System on Rear View DetailRmon Alarm Feature Switch 4200 Family Automatic IP ConfigurationDuplex Mode Quality of Service QoSInstalling the Switch Site Package ContentsChoosing a Suitable Rack-mounting Repeat steps 2 and 3 for the other side of the Switch Fitting a bracket for rack-mountingStacking Units Placing Units OnTop of Each Other Switch 4200 Family Power-upPowering-up SequencePower/Self Test LED colors Color StateFiber cables Cross-over Cable Straight-through CableApproved Gbic The 3Com approved Gbic transceivers are TransceiversInstalling the Switch Gbic Installing the Switch Setting UP for Management Automatically configured IP information Setting UpConfigure IP information manually for your Switch or view OverviewManual IP Configuration Automatic IP ConfigurationSetting UP for Management Manually Configuring IP Information Pre-requisitesSetting Up the Switch with IP Information Connecting the Workstation to the SwitchConfiguring the Workstation with IP Information Using Command Line Interface via Telnet Example top-level command line interface menu Connecting a workstation to the Switch via the console port Setting Up the Switch with IP Information Example top-level command line interface menu Automatically Configured IPViewing Viewing Automatically Configured IP Information Viewing IP Information via the Console Port Methods of Managing a Switch Refer to Setting Up Command Line Interface Management on Interface Management Command LineNetwork Using Telnet CLI Management viaChoosing a Browser Setting Up WebInterface Over the Network Setting Up SnmpManagement Protocol Snmp can manage a Switch if Management workstationDefault Users User Default Name Password Access LevelSecurity Device User Modify operation on the web interface Setting UP for Management Problem Solving For Technical Support information, see Appendix DPower LED does not light Solving ProblemsSolutions below On powering-up, the Power/Self Test LED lights yellowSolving Hardware Snmp fan fail trap hardware failure ProblemsSolving Communication Problems IP AddressingHow do you obtain a registered IP Address? Solving StackFormation Solving Software Upgrade Problems Problem Solving Safety Information Important Safety Information This must be approved for the country where it is usedImportant Safety Information ’information de Sécurité Importante Schko Wichtige Sicherheitsinformationen Vorsicht Europe Appendix a Safety Information Pin to RS-232 25-pin Null Modem CablePC-AT Serial Cable Pin to 9-pinAssignments Modem CableRJ-45 Pin Pin Number 10/100 1000Pin Number 10/100 1000 Appendix B PIN-OUTS Switch 4226T 3C17300 Protocols Used for Administration Terminal EmulationSwitch 4250T 3C17302 Switch 4228G 3C17304 Product ServicesRegister Your PurchaseOnline Access SoftwareTroubleshoot DownloadsContact Us Country Telephone Number Latin America Telephone Technical Support and Repair800 876 Appendix D Obtaining Support for Your Product Index NumbersIndex Regulatory Notices

4250T, 4226T, 4228G specifications

The 3Com 4228G, 4226T, and 4250T are professional-grade network switches designed for businesses seeking to enhance their network infrastructure. These models offer robust performance and reliability, catering to various networking needs, from small offices to large enterprise environments.

The 3Com 4228G switch is a 28-port gigabit Ethernet switch designed for high-bandwidth applications. It provides 24 Gigabit Ethernet ports with 802.3af Power over Ethernet (PoE) capability, allowing devices such as IP phones and wireless access points to be powered directly through the Ethernet cables. This feature simplifies installation and reduces additional cabling costs. The switch also supports VLAN tagging for network segmentation, improving security and performance. Its advanced traffic management lets IT administrators prioritize network traffic effectively, ensuring critical applications receive the necessary bandwidth.

On the other hand, the 3Com 4226T is a 26-port gigabit Ethernet switch, primarily designed for environments requiring a high level of connectivity without PoE. It offers similar features to the 4228G, such as VLAN support and enhanced traffic management capabilities. The 4226T is ideal for businesses that do not require power over Ethernet yet need reliable, high-speed networking capabilities. With 26 ports, this switch is an excellent choice for medium-sized enterprises looking to upgrade their network infrastructure without overwhelming their existing resources.

The 3Com 4250T is a more advanced switch, offering 48 Gigabit Ethernet ports and a robust feature set suitable for more complex networking environments. It includes Layer 2 and Layer 3 functionality, allowing for advanced routing and switching capabilities, making it highly adaptable to various network designs. The 4250T also simplifies network management through its extensive configuration options and support for IPv6. Moreover, it features an efficient cooling system and reduced power consumption, aligning with today’s growing demand for energy-efficient solutions.

All three models utilize advanced technologies such as Spanning Tree Protocol (STP) for loop prevention, QoS mechanisms to prioritize traffic, and comprehensive security features to protect the network from unauthorized access. With their different port configurations and capabilities, the 3Com 4228G, 4226T, and 4250T switches provide exceptional performance and flexibility, making them ideal for businesses aiming to enhance their networking capabilities.
Top Page Image Contents