3Com 4228G, 4250T Feature Switch 4200 Family Automatic IP Configuration, Port Status, Port Speed

Page 18

18CHAPTER 1: INTRODUCING THE SUPERSTACK 3 SWITCH 4200 SERIES

Default Settings Table 5 shows the default settings for the Switch 4200 Family:

Table 5 Default Settings

Feature

Switch 4200 Family

 

 

Automatic IP Configuration

Enabled

Port Status

Enabled

Port Speed

All ports are auto-negotiated

Duplex Mode

All ports are auto-negotiated

Flow Control

■ Enabled in half duplex

 

■ Auto-negotiated in full duplex

Broadcast Storm Control

Enabled

Virtual LANs (VLANs)

All ports belong to the untagged Default VLAN

 

(VLAN 1) with 802.1Q learning operational

IP Multicast Filtering

Filtering enabled

Rapid Spanning Tree Protocol

Enabled

Fast Start:

Enabled on all ports

RMON Alarm

Enabled

Smart Auto-Sensing

Enabled

LACP

(10/100/1000BASE-T ports and GBIC ports only)

 

Enabled

Quality of Service (QoS)

All ports prioritize NBX VoIP IP.

 

All ports set to “best effort” for all other traffic.

 

 

If you initialize a Switch unit by selecting System > Control > Initialize in the Web interface or by entering system control initialize in the Command Line Interface, the following settings are retained to allow you to connect to and manage the Switch:

■IP Address

■Subnet Mask

■Default Router

Page 17 Page 19
Image 18
Page 17 Page 19
Contents SuperStack 3Com Corporation 350 Campus Drive Marlborough, MA United States Government LegendContents Setting UP for Management Safety Information PIN -OUTSPage About this Guide Conventions Icon DescriptionConvention Description Related DocumentationAbout this Guide Introducing About the Switch FamilySwitch 4200 Family Front View DetailIntroducing the Superstack 3 Switch 4200 Series Color Indicates Port Status LEDs 10BASE-T/100BASE-TX ports Fiber GBICs1000BASE-T GBICs Port Status LEDs Gbic portsUnit LEDs Power/Self Test LEDColor Indicates Alert LEDSystem RPS. See Connecting a Redundant Power System on Rear View DetailRmon Alarm Feature Switch 4200 Family Automatic IP ConfigurationDuplex Mode Quality of Service QoSInstalling the Switch Package Contents Choosing a SuitableSite Rack-mounting Repeat steps 2 and 3 for the other side of the Switch Fitting a bracket for rack-mountingPlacing Units On Top of Each OtherStacking Units Switch 4200 Family Power-upPowering-up SequencePower/Self Test LED colors Color StateFiber cables Cross-over Cable Straight-through CableApproved Gbic The 3Com approved Gbic transceivers are TransceiversInstalling the Switch Gbic Installing the Switch Setting UP for Management Automatically configured IP information Setting UpConfigure IP information manually for your Switch or view OverviewManual IP Configuration Automatic IP ConfigurationSetting UP for Management Manually Configuring IP Information Pre-requisitesConnecting the Workstation to the Switch Configuring the Workstation with IP InformationSetting Up the Switch with IP Information Using Command Line Interface via Telnet Example top-level command line interface menu Connecting a workstation to the Switch via the console port Setting Up the Switch with IP Information Example top-level command line interface menu Configured IP ViewingAutomatically Viewing Automatically Configured IP Information Viewing IP Information via the Console Port Methods of Managing a Switch Refer to Setting Up Command Line Interface Management on Interface Management Command LineNetwork Using Telnet CLI Management viaSetting Up Web InterfaceChoosing a Browser Over the Network Setting Up SnmpManagement Protocol Snmp can manage a Switch if Management workstationDefault Users User Default Name Password Access LevelSecurity Device User Modify operation on the web interface Setting UP for Management Problem Solving For Technical Support information, see Appendix DPower LED does not light Solving ProblemsSolutions below On powering-up, the Power/Self Test LED lights yellowSolving Hardware Snmp fan fail trap hardware failure ProblemsSolving Communication Problems IP AddressingSolving Stack FormationHow do you obtain a registered IP Address? Solving Software Upgrade Problems Problem Solving Safety Information Important Safety Information This must be approved for the country where it is usedImportant Safety Information ’information de Sécurité Importante Schko Wichtige Sicherheitsinformationen Vorsicht Europe Appendix a Safety Information Pin to RS-232 25-pin Null Modem CablePC-AT Serial Cable Pin to 9-pinAssignments Modem CableRJ-45 Pin Pin Number 10/100 1000Pin Number 10/100 1000 Appendix B PIN-OUTS Switch 4226T 3C17300 Protocols Used for Administration Terminal EmulationSwitch 4250T 3C17302 Switch 4228G 3C17304 Product ServicesRegister Your PurchaseOnline Access SoftwareTroubleshoot DownloadsContact Us Country Telephone Number Latin America Telephone Technical Support and Repair800 876 Appendix D Obtaining Support for Your Product Index NumbersIndex Regulatory Notices

4250T, 4226T, 4228G specifications

The 3Com 4228G, 4226T, and 4250T are professional-grade network switches designed for businesses seeking to enhance their network infrastructure. These models offer robust performance and reliability, catering to various networking needs, from small offices to large enterprise environments.

The 3Com 4228G switch is a 28-port gigabit Ethernet switch designed for high-bandwidth applications. It provides 24 Gigabit Ethernet ports with 802.3af Power over Ethernet (PoE) capability, allowing devices such as IP phones and wireless access points to be powered directly through the Ethernet cables. This feature simplifies installation and reduces additional cabling costs. The switch also supports VLAN tagging for network segmentation, improving security and performance. Its advanced traffic management lets IT administrators prioritize network traffic effectively, ensuring critical applications receive the necessary bandwidth.

On the other hand, the 3Com 4226T is a 26-port gigabit Ethernet switch, primarily designed for environments requiring a high level of connectivity without PoE. It offers similar features to the 4228G, such as VLAN support and enhanced traffic management capabilities. The 4226T is ideal for businesses that do not require power over Ethernet yet need reliable, high-speed networking capabilities. With 26 ports, this switch is an excellent choice for medium-sized enterprises looking to upgrade their network infrastructure without overwhelming their existing resources.

The 3Com 4250T is a more advanced switch, offering 48 Gigabit Ethernet ports and a robust feature set suitable for more complex networking environments. It includes Layer 2 and Layer 3 functionality, allowing for advanced routing and switching capabilities, making it highly adaptable to various network designs. The 4250T also simplifies network management through its extensive configuration options and support for IPv6. Moreover, it features an efficient cooling system and reduced power consumption, aligning with today’s growing demand for energy-efficient solutions.

All three models utilize advanced technologies such as Spanning Tree Protocol (STP) for loop prevention, QoS mechanisms to prioritize traffic, and comprehensive security features to protect the network from unauthorized access. With their different port configurations and capabilities, the 3Com 4228G, 4226T, and 4250T switches provide exceptional performance and flexibility, making them ideal for businesses aiming to enhance their networking capabilities.
Top Page Image Contents