3Com Manual Configuration of IP Information for Switches: Console Cable and Default IP
Page 35

Manually Configuring IP Information

35

Manually

Configuring IP

Information

Connecting to a Front Panel Port

You can manually configure the Switch IP information in the following ways:

■Connecting to a front panel port — Connect a workstation using an Ethernet cable to a front panel port of the Switch. You can then manually enter IP information using the web interface or the command line interface (CLI).

■Connecting to the console port — Connect a workstation using a console cable to the console port of the Switch. You can then manually enter IP information using the command line interface (CLI).

To set up your Switch manually you can make a connection to a front panel port. You must do this whilst the Switch is offline, that is, before you connect the Switch to a network.

The procedure described in this section assumes the unit has been powered up in standalone mode and has the default IP address of 169.254.100.100.

Pre-requisites

■A workstation running Windows 2000, Windows XP or Windows Server 2003, Red Hat Linux 9, Solaris 7 or Solaris 9.

■A Network Interface Card (NIC).

■A Category 5 twisted pair Ethernet cable with RJ-45 connectors.

■A suitable Web browser — refer to “Choosing a Browser”on page 48.

■You need to have the following so that you can manually set up the Switch with IP information:

■IP address

■subnet mask

■default gateway

Page 34 Page 36
Image 35
Page 34 Page 36
Contents SuperStack United States Government Legend 3Com Corporation 350 Campus Drive Marlborough, MAContents Setting UP for Management PIN -OUTS Safety InformationPage About this Guide Convention Description ConventionsIcon Description Documentation RelatedAbout this Guide Introducing Family About the SwitchFront View Detail Switch 4200 FamilyIntroducing the Superstack 3 Switch 4200 Series Port Status LEDs Gbic ports Fiber GBICs1000BASE-T GBICs Color Indicates Port Status LEDs 10BASE-T/100BASE-TX portsAlert LED Power/Self Test LEDColor Indicates Unit LEDsRear View Detail System RPS. See Connecting a Redundant Power System onQuality of Service QoS Feature Switch 4200 Family Automatic IP ConfigurationDuplex Mode Rmon AlarmInstalling the Switch Site Package ContentsChoosing a Suitable Rack-mounting Fitting a bracket for rack-mounting Repeat steps 2 and 3 for the other side of the SwitchStacking Units Placing Units OnTop of Each Other Sequence Power-upPowering-up Switch 4200 FamilyColor State Power/Self Test LED colorsCross-over Cable Straight-through Cable Fiber cablesTransceivers Approved Gbic The 3Com approved Gbic transceivers areInstalling the Switch Gbic Installing the Switch Setting UP for Management Overview Setting UpConfigure IP information manually for your Switch or view Automatically configured IP informationAutomatic IP Configuration Manual IP ConfigurationSetting UP for Management Pre-requisites Manually Configuring IP InformationSetting Up the Switch with IP Information Connecting the Workstation to the SwitchConfiguring the Workstation with IP Information Using Command Line Interface via Telnet Example top-level command line interface menu Connecting a workstation to the Switch via the console port Setting Up the Switch with IP Information Example top-level command line interface menu Automatically Configured IPViewing Viewing Automatically Configured IP Information Viewing IP Information via the Console Port Methods of Managing a Switch Refer to Setting Up Command Line Interface Management on CLI Management via Command LineNetwork Using Telnet Interface ManagementChoosing a Browser Setting Up WebInterface Management workstation Setting Up SnmpManagement Protocol Snmp can manage a Switch if Over the NetworkUser Default Name Password Access Level Default UsersSecurity Device User Modify operation on the web interface Setting UP for Management For Technical Support information, see Appendix D Problem SolvingOn powering-up, the Power/Self Test LED lights yellow Solving ProblemsSolutions below Power LED does not lightIP Addressing ProblemsSolving Communication Problems Solving Hardware Snmp fan fail trap hardware failureHow do you obtain a registered IP Address? Solving StackFormation Solving Software Upgrade Problems Problem Solving Safety Information This must be approved for the country where it is used Important Safety InformationImportant Safety Information ’information de Sécurité Importante Schko Wichtige Sicherheitsinformationen Vorsicht Europe Appendix a Safety Information Pin to 9-pin Null Modem CablePC-AT Serial Cable Pin to RS-232 25-pinPin Number 10/100 1000 Modem CableRJ-45 Pin AssignmentsPin Number 10/100 1000 Appendix B PIN-OUTS Switch 4226T 3C17300 Terminal Emulation Protocols Used for AdministrationSwitch 4250T 3C17302 Switch 4228G 3C17304 Purchase ServicesRegister Your ProductDownloads Access SoftwareTroubleshoot OnlineContact Us Latin America Telephone Technical Support and Repair Country Telephone Number800 876 Appendix D Obtaining Support for Your Product Numbers IndexIndex Regulatory Notices

4250T, 4226T, 4228G specifications

The 3Com 4228G, 4226T, and 4250T are professional-grade network switches designed for businesses seeking to enhance their network infrastructure. These models offer robust performance and reliability, catering to various networking needs, from small offices to large enterprise environments.

The 3Com 4228G switch is a 28-port gigabit Ethernet switch designed for high-bandwidth applications. It provides 24 Gigabit Ethernet ports with 802.3af Power over Ethernet (PoE) capability, allowing devices such as IP phones and wireless access points to be powered directly through the Ethernet cables. This feature simplifies installation and reduces additional cabling costs. The switch also supports VLAN tagging for network segmentation, improving security and performance. Its advanced traffic management lets IT administrators prioritize network traffic effectively, ensuring critical applications receive the necessary bandwidth.

On the other hand, the 3Com 4226T is a 26-port gigabit Ethernet switch, primarily designed for environments requiring a high level of connectivity without PoE. It offers similar features to the 4228G, such as VLAN support and enhanced traffic management capabilities. The 4226T is ideal for businesses that do not require power over Ethernet yet need reliable, high-speed networking capabilities. With 26 ports, this switch is an excellent choice for medium-sized enterprises looking to upgrade their network infrastructure without overwhelming their existing resources.

The 3Com 4250T is a more advanced switch, offering 48 Gigabit Ethernet ports and a robust feature set suitable for more complex networking environments. It includes Layer 2 and Layer 3 functionality, allowing for advanced routing and switching capabilities, making it highly adaptable to various network designs. The 4250T also simplifies network management through its extensive configuration options and support for IPv6. Moreover, it features an efficient cooling system and reduced power consumption, aligning with today’s growing demand for energy-efficient solutions.

All three models utilize advanced technologies such as Spanning Tree Protocol (STP) for loop prevention, QoS mechanisms to prioritize traffic, and comprehensive security features to protect the network from unauthorized access. With their different port configurations and capabilities, the 3Com 4228G, 4226T, and 4250T switches provide exceptional performance and flexibility, making them ideal for businesses aiming to enhance their networking capabilities.
Top Page Image Contents