3Com 4228G, 4250T, 4226T manual Rack-mounting

Page 21

Rack-mounting 21

■ The switch is situated away from sources of conductive (electrical) dust, for example, laser printers.

 

■ The unit is installed in a clean, air conditioned environment.

 

■ The AC supply used by the switch is separate to that used by units

 

that generate high levels of AC noise, for example, air-conditioning

 

units and laser printers.

 

■ No more than eight Switch units are placed on top of one another, if

 

the units are free-standing.

 

 

Rack-mounting

The Switch 4200 Family are 1U high and will fit in most standard 19-inch

 

racks.

 

CAUTION: Disconnect all cables from the Switch before continuing.

 

Remove all self adhesive pads from the underside of the Switch if they

 

have been fitted.

 

To rack-mount your Switch:

 

1 Place the Switch the right way up on a hard flat surface, with the front

 

facing towards you.

 

2 Locate a mounting bracket over the mounting holes on one side of the

 

Switch, as shown in Figure 5.

Page 20 Page 22
Image 21
Page 20 Page 22
Contents SuperStack United States Government Legend 3Com Corporation 350 Campus Drive Marlborough, MAContents Setting UP for Management PIN -OUTS Safety InformationPage About this Guide Conventions Icon DescriptionConvention Description Documentation RelatedAbout this Guide Introducing Family About the SwitchFront View Detail Switch 4200 FamilyIntroducing the Superstack 3 Switch 4200 Series 1000BASE-T GBICs Fiber GBICsColor Indicates Port Status LEDs 10BASE-T/100BASE-TX ports Port Status LEDs Gbic portsColor Indicates Power/Self Test LEDUnit LEDs Alert LEDRear View Detail System RPS. See Connecting a Redundant Power System onDuplex Mode Feature Switch 4200 Family Automatic IP ConfigurationRmon Alarm Quality of Service QoSInstalling the Switch Package Contents Choosing a SuitableSite Rack-mounting Fitting a bracket for rack-mounting Repeat steps 2 and 3 for the other side of the SwitchPlacing Units On Top of Each OtherStacking Units Powering-up Power-upSwitch 4200 Family SequenceColor State Power/Self Test LED colorsCross-over Cable Straight-through Cable Fiber cablesTransceivers Approved Gbic The 3Com approved Gbic transceivers areInstalling the Switch Gbic Installing the Switch Setting UP for Management Configure IP information manually for your Switch or view Setting UpAutomatically configured IP information OverviewAutomatic IP Configuration Manual IP ConfigurationSetting UP for Management Pre-requisites Manually Configuring IP InformationConnecting the Workstation to the Switch Configuring the Workstation with IP InformationSetting Up the Switch with IP Information Using Command Line Interface via Telnet Example top-level command line interface menu Connecting a workstation to the Switch via the console port Setting Up the Switch with IP Information Example top-level command line interface menu Configured IP ViewingAutomatically Viewing Automatically Configured IP Information Viewing IP Information via the Console Port Methods of Managing a Switch Refer to Setting Up Command Line Interface Management on Network Using Telnet Command LineInterface Management CLI Management viaSetting Up Web InterfaceChoosing a Browser Management Protocol Snmp can manage a Switch if Setting Up SnmpOver the Network Management workstationUser Default Name Password Access Level Default UsersSecurity Device User Modify operation on the web interface Setting UP for Management For Technical Support information, see Appendix D Problem SolvingSolutions below Solving ProblemsPower LED does not light On powering-up, the Power/Self Test LED lights yellowSolving Communication Problems ProblemsSolving Hardware Snmp fan fail trap hardware failure IP AddressingSolving Stack FormationHow do you obtain a registered IP Address? Solving Software Upgrade Problems Problem Solving Safety Information This must be approved for the country where it is used Important Safety InformationImportant Safety Information ’information de Sécurité Importante Schko Wichtige Sicherheitsinformationen Vorsicht Europe Appendix a Safety Information PC-AT Serial Cable Null Modem CablePin to RS-232 25-pin Pin to 9-pinRJ-45 Pin Modem CableAssignments Pin Number 10/100 1000Pin Number 10/100 1000 Appendix B PIN-OUTS Switch 4226T 3C17300 Terminal Emulation Protocols Used for AdministrationSwitch 4250T 3C17302 Switch 4228G 3C17304 Register Your ServicesProduct PurchaseTroubleshoot Access SoftwareOnline DownloadsContact Us Latin America Telephone Technical Support and Repair Country Telephone Number800 876 Appendix D Obtaining Support for Your Product Numbers IndexIndex Regulatory Notices

4250T, 4226T, 4228G specifications

The 3Com 4228G, 4226T, and 4250T are professional-grade network switches designed for businesses seeking to enhance their network infrastructure. These models offer robust performance and reliability, catering to various networking needs, from small offices to large enterprise environments.

The 3Com 4228G switch is a 28-port gigabit Ethernet switch designed for high-bandwidth applications. It provides 24 Gigabit Ethernet ports with 802.3af Power over Ethernet (PoE) capability, allowing devices such as IP phones and wireless access points to be powered directly through the Ethernet cables. This feature simplifies installation and reduces additional cabling costs. The switch also supports VLAN tagging for network segmentation, improving security and performance. Its advanced traffic management lets IT administrators prioritize network traffic effectively, ensuring critical applications receive the necessary bandwidth.

On the other hand, the 3Com 4226T is a 26-port gigabit Ethernet switch, primarily designed for environments requiring a high level of connectivity without PoE. It offers similar features to the 4228G, such as VLAN support and enhanced traffic management capabilities. The 4226T is ideal for businesses that do not require power over Ethernet yet need reliable, high-speed networking capabilities. With 26 ports, this switch is an excellent choice for medium-sized enterprises looking to upgrade their network infrastructure without overwhelming their existing resources.

The 3Com 4250T is a more advanced switch, offering 48 Gigabit Ethernet ports and a robust feature set suitable for more complex networking environments. It includes Layer 2 and Layer 3 functionality, allowing for advanced routing and switching capabilities, making it highly adaptable to various network designs. The 4250T also simplifies network management through its extensive configuration options and support for IPv6. Moreover, it features an efficient cooling system and reduced power consumption, aligning with today’s growing demand for energy-efficient solutions.

All three models utilize advanced technologies such as Spanning Tree Protocol (STP) for loop prevention, QoS mechanisms to prioritize traffic, and comprehensive security features to protect the network from unauthorized access. With their different port configurations and capabilities, the 3Com 4228G, 4226T, and 4250T switches provide exceptional performance and flexibility, making them ideal for businesses aiming to enhance their networking capabilities.
Top Page Image Contents