3Com 4226T, 4228G, 4250T manual Package Contents, Choosing a Suitable, Site

Page 20

20CHAPTER 2: INSTALLING THE SWITCH

Package Contents

■

Switch unit

 

■

CD-ROM

 

■ Getting Started Guide (this guide)

 

■

Release Notes

 

■

Unit Information Labels

 

■

Warranty Information

 

■

Power Cord

 

■ 2 x Mounting brackets

 

■

4 x Screws

 

■ 4 x Rubber feet

 

 

Choosing a Suitable

The Switch is suited for use on a desktop, either free standing or

Site

mounted in a standard 19-inch equipment rack. Alternatively, the Switch

 

can be mounted in a wiring closet or equipment room, as an aggregator

 

for other Hubs and Switches. A rack-mounting kit containing two

 

mounting brackets is supplied with the Switch.

CAUTION: Ensure that the ventilation holes are not obstructed.

When deciding where to position the Switch, ensure that:

■Cabling is located away from:

■sources of electrical noise such as radios, transmitters and broadband amplifiers.

■power lines and fluorescent lighting fixtures

■The Switch is accessible and cables can be connected easily.

■Water or moisture cannot enter the case of the Switch.

■Air-flow is not restricted around the Switch or through the vents in the side of the Switch. 3Com recommends that you provide a minimum of 25mm (1in.) clearance.

■Air temperature around the Switch does not exceed 40 °C (104 °F).

If the Switch is installed in a 19-inch rack or closed assembly its local air temperature may be greater than room ambient temperature.

■The air is as free from dust as possible.

Page 19 Page 21
Image 20
Page 19 Page 21
Contents SuperStack 3Com Corporation 350 Campus Drive Marlborough, MA United States Government LegendContents Setting UP for Management Safety Information PIN -OUTSPage About this Guide Convention Description ConventionsIcon Description Related DocumentationAbout this Guide Introducing About the Switch FamilySwitch 4200 Family Front View DetailIntroducing the Superstack 3 Switch 4200 Series Fiber GBICs 1000BASE-T GBICsColor Indicates Port Status LEDs 10BASE-T/100BASE-TX ports Port Status LEDs Gbic portsPower/Self Test LED Color IndicatesUnit LEDs Alert LEDSystem RPS. See Connecting a Redundant Power System on Rear View DetailFeature Switch 4200 Family Automatic IP Configuration Duplex ModeRmon Alarm Quality of Service QoSInstalling the Switch Site Package ContentsChoosing a Suitable Rack-mounting Repeat steps 2 and 3 for the other side of the Switch Fitting a bracket for rack-mountingStacking Units Placing Units OnTop of Each Other Power-up Powering-upSwitch 4200 Family SequencePower/Self Test LED colors Color StateFiber cables Cross-over Cable Straight-through CableApproved Gbic The 3Com approved Gbic transceivers are TransceiversInstalling the Switch Gbic Installing the Switch Setting UP for Management Setting Up Configure IP information manually for your Switch or viewAutomatically configured IP information OverviewManual IP Configuration Automatic IP ConfigurationSetting UP for Management Manually Configuring IP Information Pre-requisitesSetting Up the Switch with IP Information Connecting the Workstation to the SwitchConfiguring the Workstation with IP Information Using Command Line Interface via Telnet Example top-level command line interface menu Connecting a workstation to the Switch via the console port Setting Up the Switch with IP Information Example top-level command line interface menu Automatically Configured IPViewing Viewing Automatically Configured IP Information Viewing IP Information via the Console Port Methods of Managing a Switch Refer to Setting Up Command Line Interface Management on Command Line Network Using TelnetInterface Management CLI Management viaChoosing a Browser Setting Up WebInterface Setting Up Snmp Management Protocol Snmp can manage a Switch ifOver the Network Management workstationDefault Users User Default Name Password Access LevelSecurity Device User Modify operation on the web interface Setting UP for Management Problem Solving For Technical Support information, see Appendix DSolving Problems Solutions belowPower LED does not light On powering-up, the Power/Self Test LED lights yellowProblems Solving Communication ProblemsSolving Hardware Snmp fan fail trap hardware failure IP AddressingHow do you obtain a registered IP Address? Solving StackFormation Solving Software Upgrade Problems Problem Solving Safety Information Important Safety Information This must be approved for the country where it is usedImportant Safety Information ’information de Sécurité Importante Schko Wichtige Sicherheitsinformationen Vorsicht Europe Appendix a Safety Information Null Modem Cable PC-AT Serial CablePin to RS-232 25-pin Pin to 9-pinModem Cable RJ-45 PinAssignments Pin Number 10/100 1000Pin Number 10/100 1000 Appendix B PIN-OUTS Switch 4226T 3C17300 Protocols Used for Administration Terminal EmulationSwitch 4250T 3C17302 Switch 4228G 3C17304 Services Register YourProduct PurchaseAccess Software TroubleshootOnline DownloadsContact Us Country Telephone Number Latin America Telephone Technical Support and Repair800 876 Appendix D Obtaining Support for Your Product Index NumbersIndex Regulatory Notices

4250T, 4226T, 4228G specifications

The 3Com 4228G, 4226T, and 4250T are professional-grade network switches designed for businesses seeking to enhance their network infrastructure. These models offer robust performance and reliability, catering to various networking needs, from small offices to large enterprise environments.

The 3Com 4228G switch is a 28-port gigabit Ethernet switch designed for high-bandwidth applications. It provides 24 Gigabit Ethernet ports with 802.3af Power over Ethernet (PoE) capability, allowing devices such as IP phones and wireless access points to be powered directly through the Ethernet cables. This feature simplifies installation and reduces additional cabling costs. The switch also supports VLAN tagging for network segmentation, improving security and performance. Its advanced traffic management lets IT administrators prioritize network traffic effectively, ensuring critical applications receive the necessary bandwidth.

On the other hand, the 3Com 4226T is a 26-port gigabit Ethernet switch, primarily designed for environments requiring a high level of connectivity without PoE. It offers similar features to the 4228G, such as VLAN support and enhanced traffic management capabilities. The 4226T is ideal for businesses that do not require power over Ethernet yet need reliable, high-speed networking capabilities. With 26 ports, this switch is an excellent choice for medium-sized enterprises looking to upgrade their network infrastructure without overwhelming their existing resources.

The 3Com 4250T is a more advanced switch, offering 48 Gigabit Ethernet ports and a robust feature set suitable for more complex networking environments. It includes Layer 2 and Layer 3 functionality, allowing for advanced routing and switching capabilities, making it highly adaptable to various network designs. The 4250T also simplifies network management through its extensive configuration options and support for IPv6. Moreover, it features an efficient cooling system and reduced power consumption, aligning with today’s growing demand for energy-efficient solutions.

All three models utilize advanced technologies such as Spanning Tree Protocol (STP) for loop prevention, QoS mechanisms to prioritize traffic, and comprehensive security features to protect the network from unauthorized access. With their different port configurations and capabilities, the 3Com 4228G, 4226T, and 4250T switches provide exceptional performance and flexibility, making them ideal for businesses aiming to enhance their networking capabilities.
Top Page Image Contents