TDK J Series JBW specifications JBW10W Type, Specifications and Standards

(2/30)

JBW10W Type

SPECIFICATIONS AND STANDARDS

Part No.			JBW05-2R0	JBW12-0R9	JBW15-0R7	JBW24-0R5
Rated output voltage and current∗			5V • 2A	12V • 0.9A	15V • 0.7A	24V • 0.5A
Maximum output power		W	10	10.8	10.5	12
Input conditions
Input voltage Eac/Edc		V	85 to 265[Rating: 100 to 240]/110 to 370
Input frequency		Hz	47 to 440[Rating: 50 to 60](Single phase)
Input current		A	0.25typ./0.35max. [AC.100V]0.15typ./0.25max.[AC.240V]
Fuse rating		A	2[AC.250V, built-in]
Surge current		A	15typ.(20max.)[AC.100V]30typ.(40max.)[AC.240V] 1st surge current, cold start, reset after 1s minimum.
Leakage current		mA	0.1typ./0.75max.[AC.100V, 60Hz]0.15typ./0.75max.[AC.240V, 60Hz]
Power factor			0.6typ./0.45typ.[AC.100/240V]
Efficiency		%	71typ.[AC.100V]	78typ.[AC.100V]	79typ.[AC.100V]	82typ.[AC.100V]
		%	71typ.[AC.240V]	79typ.[AC.240V]	80typ.[AC.240V]	83typ.[AC.240V]
Output characteristics
Output voltage Edc		V	5	12	15	24
Voltage variable range Edc		V	Fixed	Fixed	Fixed	Fixed
Maximum output current		A	2	0.9	0.7	0.5
Minimum output current		A	0	0	0	0
Overvoltage threshold Edc		V	5.75min.	13.8min.	17.25min.	27.6min.
Overcurrent threshold		A	2.5min.	1.12min.	0.87min.	0.62min.
	Source effect	%	0.4max.[Within the input voltage range]
Voltage	Load effect	%	0.8max.[0 to 100% load]
	Temperature effect	%	1max.[Ambient temperature: –10 to +50°C]
stability
	Drift(Time effect)	%	0.4max.[25°C, input and output ratings, after input voltage ON for 30min to 8h]
	Recovery	%	±4max.[50 to 100% sudden load change]
Ripple Ep-p		mV	80max.	120max.	120max.	120max.
Ripple noise Ep-p		mV	120max.	150max.	150max.	150max.
Start up time		ms	700max.(200typ.)/700max.(200typ.) [AC.100/240V]
Hold up time		ms	15typ/140typ [AC.100/240V]
Auxiliary functions
Indicator display			No
Overvoltage protection			Zenor diode clamp method, output may latch up depending on the condition.
Overcurrent protection			Fold back type, automatic recovery.
Remote ON-OFF			No
Remote sensing			No
Parallel operation			Impossible
Series operation			Inpossible
Output voltage external variable function			No
Standards
Safety standards			UL60950-1, CSA C22.2 No.60950-1(C-UL), EN60950-1(TÜV) approved.
Noise terminal voltage			FCC-B, VCCI-B, EN55011-B, EN55022-B meet.
Input harmonics current requirement			No
Constructions
External dimensions		mm	21⋅ 36⋅ 95[H⋅ W⋅ L]
Weight		g	50max.
Mounting method			Can be attached to 1 side.
Case material			No(PWB Material: CEM3)

∗Current rating(maximum output current) is determined for –10 to +50°C. Derating is required when used outside this temperature range.

• Optional input, output cable kits are available at a separate price.

• All specifications are subject to change without notice.

004-02 / 20070523 / ea122_jbw