TDK J Series JBW specifications JBW15W Type

(4/30)

JBW15W Type

SPECIFICATIONS AND STANDARDS

Part No.			JBW05-3R0	JBW12-1R3	JBW15-1R0	JAW24-0R7
Rated output voltage and current∗			5V • 3A	12V • 1.3A	15V • 1.0A	24V • 0.7A
Maximum output power		W	15	15.6	15	16.8
Input conditions
Input voltage Eac/Edc		V	85 to 265[Rating: 100 to 240]/110 to 370
Input frequency		Hz	47 to 440[Rating: 50 to 60](Single phase)
Input current		A	0.36typ./0.43max.[AC.100V]0.2typ./0.24max.[AC.240V]
Fuse rating		A	2[AC.250V, built-in]
Surge current		A	15typ./19.5max.[AC.100V]30typ./41max.[AC.240V] 1st surge current, cold start, reset after 1s minimum.
Leakage current		mA	0.2typ./0.75max.[AC.100V, 60Hz]0.3typ./0.75max.[AC.240V, 60Hz]
Power factor			0.6typ./0.45typ.[AC.100/240V]
Efficiency		%	72typ.[AC.100V]	76typ.[AC.100V]	76typ.[AC.100V]	78typ.[AC.100V]
		%	72typ.[AC.240V]	74typ.[AC.240V]	74typ.[AC.240V]	76typ.[AC.240V]
Output characteristics
Output voltage Edc		V	5	12	15	24
Voltage variable range Edc		V	Fixed	Fixed	Fixed	Fixed
Maximum output current		A	3	1.3	1	0.7
Minimum output current		A	0	0	0	0
Overvoltage threshold Edc		V	5.75min.	13.8min.	17.25min.	27.6min.
Overcurrent threshold		A	3.15min.	1.37min.	1.05min.	0.74min.
	Source effect	%	0.4max.[Within the input voltage range]
Voltage	Load effect	%	0.8max.[0 to 100% load]
	Temperature effect	%	1max.[Ambient temperature: –10 to +50°C]
stability
	Drift(Time effect)	%	0.4max.[25°C, input and output ratings, after input voltage ON for 30min to 8h]
	Recovery	%	±4max.[50 to 100% sudden load change]
Ripple Ep-p		mV	80max.	120max.	120max.	120max.
Ripple noise Ep-p		mV	120max.	150max.	150max.	150max.
Start up time		ms	200max.(25typ.)/100max.(25typ.)[AC.100/240V]		200max.(40typ.)/100max.(40typ.)[AC.100/240V]
Hold up time		ms	13typ./150typ. [AC.100/240V]
Auxiliary functions
Indicator display			No
Overvoltage protection			Zenor diode clamp method, output may latch up depending on the condition.
Overcurrent protection			Rectangular type, automatic recovery.
Remote ON-OFF			No
Remote sensing			No
Parallel operation			Impossible
Series operation			Impossible
Output voltage external variable function			No
Standards
Safety standards			UL60950-1, CSA C22.2 No.60950-1(C-UL), EN60950-1(TÜV) approved.
Noise terminal voltage			FCC-B, VCCI-B, EN55011-B, EN55022-B meet.
Input harmonics current requirement			No
Constructions
External dimensions		mm	22.6⋅ 50⋅ 95[H⋅ W⋅ L]
Weight		g	80max.
Mounting method			Can be attached to 1 side.
Case material			No(PWB Material: CEM3)

∗Current rating(maximum output current) is determined for –10 to +50°C. Derating is required when used outside this temperature range.

• Optional input, output cable kits are available at a separate price.

• All specifications are subject to change without notice.

004-02 / 20070523 / ea122_jbw