TDK J Series JBW specifications JBW50W Type

(8/30)

JBW50W Type

SPECIFICATIONS AND STANDARDS

Part No.			JBW05-10R	JBW12-4R3	JBW15-3R5	JBW24-2R1
Rated output voltage and current∗1			5V • 10A	12V • 4.3A	15V • 3.5A	24V • 2.1A
Maximum output power		W	50	51.6	52.5	50.4
Input conditions
Input voltage Eac/Edc∗2		V	85 to 265[Rating: 100 to 240]/120 to 375
Input frequency		Hz	47 to 66[Rating: 50 to 60](Single phase)
Input current		A	0.7typ./0.88max. [AC.100V]0.35typ./0.5max.[AC.240V]
Fuse rating		A	3.15[AC.250V, built-in]
Surge current		A	15typ.(30max.)[AC.100V]40typ.(60max.)[AC.240V] cold start
Leakage current		mA	0.35typ./0.75max.[AC.100V, 60Hz]0.5typ./0.75max.[AC.240V, 60Hz]
Power factor			0.99typ./0.93typ.[AC.100/240V]
Efficiency		%	77typ.[AC.100V]	80typ.[AC.100V]	80typ.[AC.100V]	81typ.[AC.100V]
		%	79typ.[AC.240V]	81typ.[AC.240V]	81typ.[AC.240V]	83typ.[AC.240V]
Output characteristics
Output voltage Edc		V	5	12	15	24
Voltage variable range Edc		V	4.5 to 5.5	10.8 to 13.2	13.5 to 16.5	21.6 to 26.4
Maximum output current		A	10	4.3	3.5	2.1
Minimum output current		A	0	0	0	0
Overvoltage threshold Edc		V	5.75 to 6.9	13.8 to 16.8	17.2 to 21	27.6 to 33.6
Overcurrent threshold		A	10.5min.	5.4min.	4.4min.	2.7min.
	Source effect	%	0.4max.[Within the input voltage range]
Voltage	Load effect	%	0.8max.[0 to 100% load]
	Temperature effect	%	1max.[Ambient temperature: –10 to +50°C]
stability
	Drift(Time effect)	%	0.4max.[25°C, input and output ratings, after input voltage ON for 30min to 8h]
	Recovery	%	±4max.[50 to 100% sudden load change]
Ripple Ep-p		mV	80max.	120max.	120max.	120max.
Ripple noise Ep-p		mV	120max.	150max.	150max.	150max.
Start up time		ms	500max.(400typ.)/500max.(400typ.) [AC.100/240V]
Hold up time		ms	20typ./20typ. [AC.100/240V]
Auxiliary functions
Indicator display			No
Overvoltage protection			Voltage shut-down type.
Overcurrent protection			Rectangular type, automatic recovery.
Remote ON-OFF			No
Remote sensing			No
Parallel operation			Impossible
Series operation			Possible
Output voltage external variable function			No
Standards
Safety standards			UL60950-1, CSA C22.2 No.60950-1(C-UL), EN60950-1(TÜV) approved.
Noise terminal voltage			FCC-B, VCCI-B, EN55011-B, EN55022-B meet.
Input harmonics current requirement			EN61000-3-2 meet.
Constructions
External dimensions		mm	26⋅ 55⋅ 190[H⋅ W⋅ L]
Weight		g	220max.
Mounting method			Can be attached to 1 side.
Case material			No(PWB Material: CEM3)

∗1 Current rating(maximum output current) is determined for –10 to +50°C. Derating is required when used outside this temperature range.

∗2 Please note that the deterioration of parts is occasionally caused when operating for a long time(over 10 minutes) with the voltage below the range of the input voltage.

• Optional input, output cable kits are available at a separate price.

• All specifications are subject to change without notice.

004-02 / 20070523 / ea122_jbw