SUPER MICRO Computer X8DTG-DF user manual Bios Error Beep Codes, Error Message

Page 87

Appendix A: BIOS POST Error Codes

Appendix A

BIOS Error Beep Codes

During the POST (Power-On Self-Test) routines, which are performed each time the system is powered on, errors may occur.

Non-fatal errors are those which, in most cases, allow the system to continue the boot-up process. The error messages normally appear on the screen.

Fatal errors are those which will not allow the system to continue the boot-up procedure. If a fatal error occurs, you should consult with your system manufac- turer for possible repairs.

A-1 BIOS Error Beep Codes

BIOS Error Beep Codes

Beep Code

1 beep

Error Message

Refresh

Description

Circuits have been reset. (Ready to power up)

5 short beeps + 1 long

Memory error

No memory detected in the

beep

 

system

 

 

 

8 beeps

Display memory

Video adapter missing or with

 

read/write error

faulty memory

1 continuous beep

System Overheat

1 continuous beep with the

(with the front panel

 

front panel OH LED on

OH LED on)

 

 

A-1

Image 87
Contents USER’S Manual Manual Revision Release Date July 6 About This Manual About This Motherboard Manual OrganizationConventions Used in the Manual Asia-Pacific Contacting SupermicroHeadquarters EuropeContacting Supermicro Table of Contents Troubleshooting Main Setup BiosOverview Chapter IntroductionX8DTG-DF Motherboard Image X8DTG-DF Motherboard Layout ICH10R BiosX8DTG-DF Quick Reference ICH10R BiosJPW2/JPW3 Connector DescriptionCPU Motherboard FeaturesOther Block Diagram of the 5500 Series Processor Platform Chipset Overview PC Health Monitoring Special FeaturesMain Switch Override Mechanism Acpi FeaturesPower Supply Slow Blinking LED for Suspend-State IndicatorOverview of the Winbond WPCM450 Controller Installation Motherboard Installation Installation InstructionsTools Needed Processor and Heatsink Installation Socket Clip Load PlatePlastic Cap Socket Keys CPU Keys Load Plate Installing a CPU Heatsink Removing the Heatsink Memory Installation DIMMsBranch 84 GB Dimm Module Population ConfigurationDimm Population Table Possible System Memory Allocation & AvailabilityTo Install Installing and Removing DIMMsBack Panel Connectors/IO Ports Control Panel Connectors/IO PortsBack Panel USB 0/1 Pin Definitions Back Panel Connector Pin DefinitionsUniversal Serial Bus USB USB USB 2/3Ethernet Ports NC No Connection LAN1 LAN2 Ipmi dedicated LANLAN Ports Pin Definition Serial Port Pin Definitions COM1 Video ConnectorSerial Ports COM Port VGA PortPin# Definition Ground Button Unit Identifier SwitchesRear UID Switch FP UID Switch & UID LED Rear UID LED UID SwitchFront Control Panel JF1 Header PinsFront Control Panel Pin Definitions Power LEDHDD/FP UID Switch HDD LED/FP UID Switch LEDPin# Definition 11 NIC1 Activity 12 NIC1 Link NIC1 LED IndicatorNIC2 LED Indicator NIC1 LED B. NIC2 LEDUID LED Power Fail LEDOverheat OH/Fan Fail/PWR Fail/UID LED OH/Fan Fail/PWR FailReset Button Pin Definitions JF1 Reset ButtonPower Button Reset Button B. PWR Button12V Connecting CablesPin Main Power Connector Pin Definitions Pin# Definition Pin # PS On GroundFan Headers NMI Button Pin Definitions JF1 NMI HeaderInternal Buzzer NMI Header Internal SpeakerChassis Intrusion Pin Definitions JL1 Sgpio HeadersChassis Intrusion SGPIO0 SBPIO1SMB for Ipmi Pin Definitions PWR I2C SMB ConnectorPWR I2C SMB Ipmb SMBGlan Enable Jumper Settings Jumper SettingsGlan Enable/Disable Glan Port 1/2 EnableCmos Clear Watch Dog Enable/DisableClear Cmos Watch Dog Enable Watch Dog Jumper SettingsVGA Enable VGA Enable/Disable Jumper Settings JPG1Both Jumpers Definition Pins Enabled Disabled JUID-OW -Overwriting Jumper Settings Juidow -OverwritingJuidled Onboard Indicators Glan LEDsLED LE1 LE2 Onboard Power LEDBMC Activity LED Indicator LED Settings BMC Activity LEDSerial ATA Pin Definitions Serial ATA ConnectionsSerial ATA Ports SATA1 SATA2 SATA3 SATA4 SATA5 SATA6Page Troubleshooting Procedures Before Power OnNo Power Losing the System’s Setup Configuration Memory ErrorsNo Video Frequently Asked Questions Technical Support ProceduresReturning Merchandise for Service Starting Bios Setup Utility How To Change the Configuration DataIntroduction Main Setup Starting the Setup UtilitySystem Time/System Date Supermicro X8DTG-DF ProcessorSystem Memory Boot Features Advanced Setup ConfigurationsProcessor and Clock Options Power ConfigurationIntel Eist Technology Hardware Prefetcher Available when supported by the CPUC1E Support Active Processor CoresCPU Bridge Configuration Advanced Chipset ControlMemory Frequency Memory ModeMemory ECC Error Threshold QPI L0s and L1Temperature Rise Hysteresis Temperature Closed Loop OnlyGuardband Temperature Closed Loop Only Inlet TemperatureSouth Bridge Configuration North Bridge ConfigurationIDE/SATA/Floppy Configuration Type LBA/Large ModePIO Mode SATA#2 ConfigurationDMA Mode PCI/PnP Configuration Super IO Device Configuration Remote Access ConfigurationTerminal Type Sredir Memory Display DelayCPU Overheat Alarm Hardware Health ConfigurationCPU 1 Temperature/CPU 2 Temperature CPU Temperature/System TemperatureSystem Fan Monitor Acpi Version Features Acpi Apic SupportACPI Configuration Fan1 ~ Fan 8 ReadingGeneral Whea Configuration IPMI ConfigurationView BMC System Event Log Status Set LAN ConfigurationClear BMC System Event Log Clear BMC System Log Channel NumberIP Address Configuration MAC Address ConfigurationSubnet Mask Configuration Security Settings Gateway Address ConfigurationDMI Event Log Change User Password Supervisor PasswordUser Password Change Supervisor PasswordRemovable Drives Boot ConfigurationBoot Device Priority Hard Disk DrivesExit Options Bios Recovery How to Recover the Amibios Image -the Main Bios BlockBoot Sector Recovery from a USB Device Boot Sector Recovery from a Serial Port Serial Flash Boot Sector Recovery from an IDE CD-ROMPage Page X8DTG-DF User’s Manual Bios Error Beep Codes Error MessageBeep Code Page Installing the Windows OS for a RAID System Appendix B Installing the Windows OSInstalling the Windows OS for a Non-RAID System Driver/Tool Installation Display Screen Installing Software ProgramsConfiguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control