SUPER MICRO Computer X8SIL user manual Installing DDR3 Memory, Dimm Installation, Memory Support

Page 32

X8SIL/X8SIL-F User's Manual

2-3 Installing DDR3 Memory

Note: Check the Supermicro web site for recommended memory modules.

CAUTION

Exercise extreme care when installing or removing

DIMM modules to prevent any possible damage.

DIMM Installation

1.Insert the desired number of DIMMs into the memory slots, starting with DIMM1A. Insert each DIMM module vertically into its slot. Pay attention to the notch along the bottom of the module to prevent incorrect DIMM module installation.

2.Gently press down on the DIMM module until it snaps into place in the slot. Repeat step 1 to install DIMM1B if needed.

Memory Support

The X8SIL/X8SIL-F supports up to 16GB of DDR3 ECC UDIMM or up to 32GB of ECC DDR3 RDIMM (1333/1066/800 MHz in 4 DIMM slots.) Populating these DIMM modules with a pair of memory modules of the same type and same size will result in interleaved memory, which will improve memory performance. Please refer to the table below:

Platform

DIMM Type

Intel® Xeon® Series Processors

X8SIL/X8SIL-F

Non-ECC UDIMM Only

Not Supported

 

 

 

 

 

 

ECC UDIMM Only

Supported (see Table 1)

 

RDIMM Only (with ECC)

Supported (see Table 2)

 

 

 

 

 

 

Mixed ECC with non-ECC

Not Supported

 

 

 

 

 

 

Mixed UDIMM/RDIMM

Not Supported

 

 

 

 

 

 

 

 

Table 1 - DDR3 ECC/Unbuffered (UDIMM) Memory Support

ECC UDIMM

 

1Gb (x8 DRAM)

 

2Gb (x8 DRAM)

Single Rank

 

Up to 4GB

 

Up to 8GB

 

 

(4 x 1GB DIMM Modules)

(4 x 2GB DIMM Modules)

Dual Rank

 

Up to 8GB

 

Up to 16GB

 

 

(4 x 2GB DIMM Modules)

(4 x 4GB DIMM Modules)

Quad Rank

 

Not Supported

 

Not Supported

2-10

Page 31 Page 33
Image 32
Page 31 Page 33
Contents X8SIL X8SIL-F Page About This Motherboard Manual Organization Conventions Used in the ManualContacting Supermicro HeadquartersEurope Asia-PacificTable of Contents Vii How To Change the Configuration Data Main Setup Advanced Setup ConfigurationsInstalling Drivers Configuring Supero Doctor IntroductionTable of Contents Checklist OverviewMotherboard X8SIL-F Image Important Notes to the User 13,14 11,12X8SIL/X8SIL-F Headers/Connectors Number Description X8SIL/X8SIL-F LED Indicators Number33,32,27,23,7 Description Color/State StatusMotherboard Features Power Configuration Devices USB Devices X8SIL-FKeyboard/Mouse Serial COM PortsOther DimensionsCD Utilities Block Diagram RoHS 6/6 X8SIL / X8SIL-F System Block DiagramIntel 3400/3420 Chipset Features Chipset OverviewPower Configuration Settings PC Health MonitoringPower Supply Slow Blinking LED for Suspend-State IndicatorBios Support for USB Keyboard Main Switch Override MechanismSuper I/O X8SIL/X8SIL-F User’s Manual Unpacking PrecautionsStatic-Sensitive Devices Processor and Heatsink Installation Installing the LGA1156 ProcessorPage Page Installing a Passive CPU Heatsink Removing the Heatsink Installing an Active Fan CPU Heatsink Page Active Heatsink Removal Memory Support Installing DDR3 MemoryDimm Installation Populated Any combination Per Channel Memory Population GuidelinesDDR3 ECC Registered Rdimm Memory Support Installing and Removing DIMMs To RemovePossible System Memory Allocation & Availability Location of Mounting Holes Motherboard InstallationTools Needed Installation Instructions Connectors/IO Ports Back Panel Connectors and IO PortsMouse Green MouseKeyboard Universal Serial Bus USB USBPN3 USBPP3Ethernet Ports LAN Ports Pin DefinitionSerial Ports COM1 COM2Video Connector VGAJF1 Header Pins Front Control PanelPower LED Front Control Panel Pin DefinitionsOverheat OH/Fan Fail OH/Fan FailReset Button PWR Button Reset ButtonPower Button Connecting Cables ATX Main PWR & CPU PWR ConnectorsRequired Pin ATX Main PWR Pin Processor PWRFan Headers Chassis IntrusionInternal Buzzer Speaker Header Internal BuzzerSpeaker Onboard Power LED Power Supply I2C ConnectorAlarm Reset Sgpio 0/1 HeadersJumper Settings LAN Port Enable/DisableLAN Port 1 Enable B. LAN Port 2 Enable Explanation of JumpersClear Cmos JI2C1 JI2C2 PCI Slot SMB EnableCmos Clear VGA Enable VGA EnableUSB Wake-Up BMC JumperBP USB 0/1 Wake-up BMC JumperOnboard Indicators LAN 1/LAN 2 LEDsIpmi Dedicated LAN LEDs LAN PortIpmi Heartbeat LED Onboard PWR LED B. Ipmi Heartbeat LEDSata and Floppy Drive Connections Sata ConnectionsFloppy Connector FloppyTroubleshooting Procedures Before Power OnNo Power No VideoLosing the System’s Setup Configuration Technical Support ProceduresMemory Errors Question What type of memory does my motherboard support? Frequently Asked QuestionsQuestion How do I update my BIOS? Question Whats on the CD that came with my motherboard? Page Battery Installation Battery Removal and InstallationBattery Removal Returning Merchandise for Service Page Introduction Starting Bios Setup UtilityHow To Change the Configuration Data Main Setup How to Start the Setup UtilitySystem Memory System Time/System DateProcessor Advanced Setup Configurations BOOT FeatureProcessor & Clock Options Intel Eist Technology Hardware Prefetcher Available when supported by the CPUActive Processor Cores State package limit setting C1E SupportIntel C-STATE Tech C1 Auto DemotionMemory Remap Feature Active State Power ManagementAdvanced Chipset Control Intel VT-dSATA / Floppy Configuration LBA/Large Mode PIO ModeType Block Multi-Sector TransferDMA Mode A.R.T. For Hard disk drivesPCI/PnP Configuration Super IO Device Configuration Remote Access ConfigurationHardware Health Configuration System Temperature CPU TemperatureFan Speed Control Modes Fan1 ~ Fan 6 ReadingACPI Configuration IPMI Configuration X8SIL-F OnlySet LAN Configuration Ipmi Firmware RevisionStatus of BMC View BMC System Event LogEvent Log Configuration Intel TXT LT ConfigurationSecurity Settings Supervisor PasswordUser Password Change Supervisor PasswordBoot Sector Virus Protection Boot SettingsBoot Device Priority Retry Boot Devices Exit OptionsRemovable Drives CD/DVD DrivesLoad Optimal Defaults Load Fail-Safe DefaultsDiscard Changes and Exit Discard ChangesX8SIL/X8SIL-F Appendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Installing Drivers Driver/Tool Installation Display ScreenConfiguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Recovery Process from a USB Device/Drive Recommended Method Part 1 Boot Sector Recovery ProcessRecovery Process from an IDE/SATA Atapi Disc Drive Part 2 Bios Reprogramming Re-Flashing
Related manuals
Manual 102 pages 50.95 Kb

X8SIL specifications

SUPER MICRO Computer X8SIL, X8SIL-F, and X8SIL-V are advanced server motherboards designed to meet the demanding needs of today's data centers and enterprise environments. These motherboards from Supermicro deliver exceptional performance, scalability, and reliability, making them suitable for a wide range of applications, including virtualization, cloud computing, and database management.

One of the main features of the X8SIL series is its compatibility with Intel's Xeon 5500 and 5600 series processors. This allows users to harness the power of multi-core technology, ensuring optimal performance for both single-threaded and multi-threaded applications. With support for up to 144GB of DDR3 ECC memory, the X8SIL motherboards provide ample memory bandwidth, enhancing the overall system performance and efficiency.

The X8SIL-F variant includes an integrated IPMI (Intelligent Platform Management Interface) feature, which enables remote management and monitoring of the system. This technology allows IT administrators to proactively manage server health, perform remote troubleshooting, and ensure minimal downtime. Additionally, the X8SIL-F supports Supermicro's Green Computing technology, which helps reduce power consumption and enhance energy efficiency, leading to lower operational costs.

In terms of storage, the X8SIL series offers multiple SATA and SAS interface options, facilitating a wide range of storage configurations. The motherboards feature six SATA II ports and optional SAS capabilities, allowing users to implement RAID setups for improved performance and data redundancy. This flexibility in storage solutions is crucial for environments that require high availability and reliability.

The X8SIL motherboard series is equipped with a range of I/O ports, including multiple USB ports, PCI Express slots, and Gigabit Ethernet interfaces. This extensive connectivity ensures that users can easily expand and customize their systems according to specific application needs. The onboard Gigabit Ethernet ports provide fast network access, which is essential for data-intensive workloads.

Furthermore, the X8SIL, X8SIL-F, and X8SIL-V boast an efficient thermal design. These motherboards feature robust heat sinks and fan headers, which help maintain optimal operating temperatures, even under heavy workloads. This thermal efficiency is critical in extending the lifespan of components and ensuring consistent performance.

In summary, SUPER MICRO Computer's X8SIL, X8SIL-F, and X8SIL-V motherboards stand out with their strong performance, advanced management features, flexible storage options, and efficient thermal design. These characteristics make them ideal choices for businesses looking to build reliable and scalable data center solutions.
Top Page Image Contents