SUPER MICRO Computer X8SIL user manual Processor & Clock Options

Page 73

Chapter 4: AMI BIOS

Wait For 'F1' If Error

This forces the system to wait until the 'F1' key is pressed if an error occurs. The options are Disabled and Enabled.

Hit 'Del' Message Display

This feature displays "Press DEL to run Setup" during POST. The options are Enabled and Disabled.

Watch Dog Function

If enabled, the Watch Dog Timer will allow the system to reboot when it is inactive for more than 5 minutes. The options are Enabled and Disabled.

Restore on AC Power Loss

Use this feature to set the power state after a power outage. Select Power-Off for the system power to remain off after a power loss. Select Power-On for the system power to be turned on after a power loss. Select Last State to allow the system to resume its last state before a power loss. The options are Power-On, Power-Off and Last State.

Interrupt 19 Capture

Interrupt 19 is the software interrupt that handles the boot disk function. When this item is set to Enabled, the ROM BIOS of the host adaptors will "capture" Interrupt 19 at boot and allow the drives that are attached to these host adaptors to function as bootable disks. If this item is set to Disabled, the ROM BIOS of the host adap- tors will not capture Interrupt 19, and the drives attached to these adaptors will not function as bootable devices. The options are Enabled and Disabled.

Processor & Clock Options

Warning: Take Caution when changing the Advanced settings. An incorrect value, a very high DRAM frequency or incorrect DRAM timing may cause system to become unstable. When this occurs, revert to the default setting.

CPU Ratio

This feature allows the user to use the CPU clock multiplier to multiply CPU speed in order to enhance performance. Select Manual to Manually set the multiplier setting. Select Auto for the BIOS to automatically select the CPU multiplier setting for your system. The options are Auto and Manual.

Clock Spread Spectrum

Select Enable to use the feature of Clock Spectrum, which will allow the BIOS to monitor and attempt to reduce the level of Electromagnetic Interference caused by

4-5

Image 73
Contents X8SIL X8SIL-F Page Conventions Used in the Manual About This Motherboard Manual OrganizationHeadquarters Contacting SupermicroEurope Asia-PacificTable of Contents Vii Main Setup Advanced Setup Configurations How To Change the Configuration DataInstalling Drivers Configuring Supero Doctor IntroductionTable of Contents Overview ChecklistMotherboard X8SIL-F Image Important Notes to the User 11,12 13,14X8SIL/X8SIL-F LED Indicators Number X8SIL/X8SIL-F Headers/Connectors Number Description33,32,27,23,7 Description Color/State StatusMotherboard Features Devices USB Devices X8SIL-F Power ConfigurationKeyboard/Mouse Serial COM PortsCD Utilities DimensionsOther X8SIL / X8SIL-F System Block Diagram Block Diagram RoHS 6/6Chipset Overview Intel 3400/3420 Chipset FeaturesPC Health Monitoring Power Configuration SettingsSlow Blinking LED for Suspend-State Indicator Power SupplyBios Support for USB Keyboard Main Switch Override MechanismSuper I/O X8SIL/X8SIL-F User’s Manual Static-Sensitive Devices PrecautionsUnpacking Installing the LGA1156 Processor Processor and Heatsink InstallationPage Page Installing a Passive CPU Heatsink Removing the Heatsink Installing an Active Fan CPU Heatsink Page Active Heatsink Removal Dimm Installation Installing DDR3 MemoryMemory Support DDR3 ECC Registered Rdimm Memory Support Memory Population GuidelinesPopulated Any combination Per Channel To Remove Installing and Removing DIMMsPossible System Memory Allocation & Availability Tools Needed Motherboard InstallationLocation of Mounting Holes Installation Instructions Back Panel Connectors and IO Ports Connectors/IO PortsKeyboard MouseMouse Green USBPN3 USBPP3 Universal Serial Bus USBLAN Ports Pin Definition Ethernet PortsCOM1 COM2 Serial PortsVGA Video ConnectorFront Control Panel JF1 Header PinsFront Control Panel Pin Definitions Power LEDOH/Fan Fail Overheat OH/Fan FailPower Button Reset ButtonReset Button PWR Button ATX Main PWR & CPU PWR Connectors Connecting CablesRequired Pin ATX Main PWR Pin Processor PWRChassis Intrusion Fan HeadersSpeaker Internal BuzzerInternal Buzzer Speaker Header Power Supply I2C Connector Onboard Power LEDSgpio 0/1 Headers Alarm ResetLAN Port Enable/Disable Jumper SettingsLAN Port 1 Enable B. LAN Port 2 Enable Explanation of JumpersCmos Clear PCI Slot SMB EnableClear Cmos JI2C1 JI2C2 VGA Enable VGA EnableBMC Jumper USB Wake-UpBP USB 0/1 Wake-up BMC JumperLAN 1/LAN 2 LEDs Onboard IndicatorsIpmi Dedicated LAN LEDs LAN PortOnboard PWR LED B. Ipmi Heartbeat LED Ipmi Heartbeat LEDSata Connections Sata and Floppy Drive ConnectionsFloppy Floppy ConnectorBefore Power On Troubleshooting ProceduresNo Power No VideoMemory Errors Technical Support ProceduresLosing the System’s Setup Configuration Question How do I update my BIOS? Frequently Asked QuestionsQuestion What type of memory does my motherboard support? Question Whats on the CD that came with my motherboard? Page Battery Removal Battery Removal and InstallationBattery Installation Returning Merchandise for Service Page How To Change the Configuration Data Starting Bios Setup UtilityIntroduction How to Start the Setup Utility Main SetupProcessor System Time/System DateSystem Memory BOOT Feature Advanced Setup ConfigurationsProcessor & Clock Options Active Processor Cores Hardware Prefetcher Available when supported by the CPUIntel Eist Technology C1E Support State package limit settingIntel C-STATE Tech C1 Auto DemotionActive State Power Management Memory Remap FeatureAdvanced Chipset Control Intel VT-dSATA / Floppy Configuration PIO Mode LBA/Large ModeType Block Multi-Sector TransferA.R.T. For Hard disk drives DMA ModePCI/PnP Configuration Remote Access Configuration Super IO Device ConfigurationHardware Health Configuration CPU Temperature System TemperatureFan1 ~ Fan 6 Reading Fan Speed Control ModesIPMI Configuration X8SIL-F Only ACPI ConfigurationIpmi Firmware Revision Set LAN ConfigurationStatus of BMC View BMC System Event LogIntel TXT LT Configuration Event Log ConfigurationSupervisor Password Security SettingsUser Password Change Supervisor PasswordBoot Device Priority Boot SettingsBoot Sector Virus Protection Exit Options Retry Boot DevicesRemovable Drives CD/DVD DrivesLoad Fail-Safe Defaults Load Optimal DefaultsDiscard Changes and Exit Discard ChangesX8SIL/X8SIL-F Recoverable Post Error Beep Codes Appendix a Post Error Beep CodesPage Driver/Tool Installation Display Screen Installing DriversConfiguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Part 1 Boot Sector Recovery Process Recovery Process from a USB Device/Drive Recommended MethodPart 2 Bios Reprogramming Re-Flashing Recovery Process from an IDE/SATA Atapi Disc Drive
Related manuals
Manual 102 pages 50.95 Kb

X8SIL specifications

SUPER MICRO Computer X8SIL, X8SIL-F, and X8SIL-V are advanced server motherboards designed to meet the demanding needs of today's data centers and enterprise environments. These motherboards from Supermicro deliver exceptional performance, scalability, and reliability, making them suitable for a wide range of applications, including virtualization, cloud computing, and database management.

One of the main features of the X8SIL series is its compatibility with Intel's Xeon 5500 and 5600 series processors. This allows users to harness the power of multi-core technology, ensuring optimal performance for both single-threaded and multi-threaded applications. With support for up to 144GB of DDR3 ECC memory, the X8SIL motherboards provide ample memory bandwidth, enhancing the overall system performance and efficiency.

The X8SIL-F variant includes an integrated IPMI (Intelligent Platform Management Interface) feature, which enables remote management and monitoring of the system. This technology allows IT administrators to proactively manage server health, perform remote troubleshooting, and ensure minimal downtime. Additionally, the X8SIL-F supports Supermicro's Green Computing technology, which helps reduce power consumption and enhance energy efficiency, leading to lower operational costs.

In terms of storage, the X8SIL series offers multiple SATA and SAS interface options, facilitating a wide range of storage configurations. The motherboards feature six SATA II ports and optional SAS capabilities, allowing users to implement RAID setups for improved performance and data redundancy. This flexibility in storage solutions is crucial for environments that require high availability and reliability.

The X8SIL motherboard series is equipped with a range of I/O ports, including multiple USB ports, PCI Express slots, and Gigabit Ethernet interfaces. This extensive connectivity ensures that users can easily expand and customize their systems according to specific application needs. The onboard Gigabit Ethernet ports provide fast network access, which is essential for data-intensive workloads.

Furthermore, the X8SIL, X8SIL-F, and X8SIL-V boast an efficient thermal design. These motherboards feature robust heat sinks and fan headers, which help maintain optimal operating temperatures, even under heavy workloads. This thermal efficiency is critical in extending the lifespan of components and ensuring consistent performance.

In summary, SUPER MICRO Computer's X8SIL, X8SIL-F, and X8SIL-V motherboards stand out with their strong performance, advanced management features, flexible storage options, and efficient thermal design. These characteristics make them ideal choices for businesses looking to build reliable and scalable data center solutions.