SUPER MICRO Computer X7SBL-LN1/LN2 user manual Universal Serial Bus USB, Chassis Intrusion

Page 34

X7SBL-LN1/LN2 User’s Manual

Universal Serial Bus (USB)

There are seven USB 2.0 (Universal Serial Bus) ports/headers on the motherboard. Two of them are Back Panel USB ports (USB 0-1: J15). Another two USB Headers: (USB 2-3: J44) and (USB 4-5 : J45) can provide front access USB connections. (FP USB 6: J47) is a front panel USB con- nection. See the tables on the right for pin defi nitions.

Back Panel USB

(J15)

Pin# Defi nitions

1+5V

2PO-

3PO+

4Ground

5 N/A

Front Panel & Front Accessible USB

Pin Defi nitions (J44, J45, J47)

USB 2, USB 4, USB 6

USB 3, USB 5

Pin # Defi nition

Pin # Defi nition

Chassis Intrusion

A Chassis Intrusion header is located at JL1 on the motherboard. Attach an

1+5V

2PO-

3PO+

4Ground

5No connec- tion

1+5V

2PO-

3PO+

4Ground

5 Key

appropriate cable from the chassis to inform you of a chassis intrusion when it is opened.

A

Chassis Intrusion

Pin Defi nitions (JL1)

Pin# Defi nition

1Intrusion Input

2 Ground

A.Backpanel USB 0-1

B.Front Accessible USB 2-3

C.Front Accessible USB 4-5

D.Front Panel USB 6

E.Chassis Intrusion

E

C

B

D

2-16

Image 34
Contents X7SBL-LN1/LN2 Manual Revision 1.0c Release Date February 6 Manual Organization About This ManualConventions Used in the Manual Table of Contents Troubleshooting Bios Checklist OverviewEurope HeadquartersAsia-Pacifi c X7SBL-LN1/LN2 Image Motherboard Layout Important Notes to the UserX7SBL-LN1/LN2 Quick Reference JPUSB1/JPUSB2Motherboard Features Dimensions Acpi FeaturesTemperature Onboard I/OBlock Diagram Intel 3200 Chipset System Block DiagramChipset Overview Intel ICH9R System FeaturesMemory Controller Hub MCH Recovery from AC Power Loss Special FeaturesEnvironmental Temperature Control PC Health MonitoringCPU Overheat LED and Control Acpi FeaturesVirtualization Technology System Resource AlertSlow Blinking LED for Suspend-State Indicator Super I/OStatic-Sensitive Devices Motherboard InstallationPrecautions UnpackingProcessor and Heatsink Installation Installation OverviewInstallation of the LGA 775 Processor TrianglePage Installation of the Heatsink Removal of the Heatsink Dimm Installation Installing DIMMsMemory Support Installing and Removing DIMMs Top View of DDR2Back Panel Connectors Control Panel Connectors/IO PortsBack Panel Connectors/IO Ports Back Panel I/O Port Locations and Defi nitionsHeader Pins Front Control PanelPower LED Front Control Panel Pin Defi nitions NMI ButtonNIC1/NIC2 LED Indicators HDD LEDPower Fail LED Overheat/Fan Fail LED OHReset Button Power ButtonATX Power Connector Connecting CablesProcessor Power Connector Universal Serial Bus USB Chassis IntrusionATX PS/2 Keyboard and PS/2 Mouse Ports Serial PortsExternal Speaker/Internal Buzzer PWR LEDVGA Connector Glan Giga-bit Ethernet PortsFan Headers Wake-On-Ring Wake-On-LANPower Fault PWR Supply Failure Power SMB ConnectorGlan Enable/Disable Jumper SettingsExplanation of Jumpers Watch Dog Enable/Disable Clear CmosVGA Enable/Disable PCI/PCI-E Slots to SMB SpeedsForce-Power-On Enable/Disable USB Wake-Up Onboard Indicators Glan LEDsOnboard Power LED LE1 Floppy Connector 9Floppy and SIM 1U Ipmi ConnectionsSIM 1U Ipmi X7SBL-LN1/LN2 User’s Manual Before Power On Troubleshooting ProceduresNo Power Losing the System’s Setup Confi guration Memory ErrorsNo Video Technical Support Procedures Frequently Asked Questions Question What type of memory does my motherboard support?Returning Merchandise for Service X7SBL-LN1/LN2 User’s Manual Starting the Setup Utility System BiosHow To Change the Confi guration Data IntroductionRunning Setup Main Bios SetupSystem Date Main Bios Setup Menu ΥMain Setup FeaturesSystem Time Legacy Diskette aHard Disk Pre-Delay Bios DateBios Revision Native Mode OperationΥIDE Channel 0 Master/Slave/SATA Port2/SATA Port3 Sata Ahci Legacy EnableType LBA Format LBA Mode ControlCHS Format Multi-Sector TransfersInstalled Memory Transfer ModeUltra DMA Mode Bit I/OQuiet Boot Advanced SetupΥBoot Features QuickBoot ModePower Button Behavior Post ErrorsAcpi Mode Resume On Modem RingWatch Dog Power Loss ControlΥAdvanced Processor Options Summary ScreenHyperthreading Available when supported by the CPU Set Maximum Ext. CPUID=3 Intel Virtualization Technology Available when supported byC1 Enhanced Mode Available when supported by the CPU Echo TPRΥAdvanced Chipset Control Clock Spectrum FeatureCPU and the OS Memory Remapping Enable VT-DHigh Precision Event Timer Route Port 80h Cycles toΥMemory Cache Cache System Bios AreaCache Video Bios Area Cache Base 0-512KΥPNP Confi guration ΥPCI32 Slot#1 PCI32 Slot#2ΥSlot 3 PCI-Exp ΥSlot 4 PCI-ExpΥOnboard LAN 1 and Onboard LAN ΥI/O Device Confi gurationBase I/O Address KBC Clock InputSerial Port a InterruptΥDMI Event Logging ΥConsole Redirection ΥHardware MonitoringCPU Overheat Alarm CPU Temperature Fan1 Fan System TemperatureFan Speed Control Modes Security Settings Voltage MonitoringSet Supervisor Password Supervisor Password IsUser Password Is Set User PasswordBoot Settings Boot Priority Order/Excluded from Boot OrdersExit Saving Changes Load Setup DefaultsExit Exit Discarding ChangesDiscard Changes Save ChangesPage Appendix a Bios Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B Installing the Windows OS Page Appendix C Installing Other Software Programs and Drivers Confi guring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Disclaimer