SUPER MICRO Computer X7SBL-LN1/LN2 user manual Glan Giga-bit Ethernet Ports, VGA Connector

Page 37

GLAN (Giga-bit Ethernet Ports)

Two G-bit Ethernet ports (GLAN1/

GLAN2) are located next to the VGA

Connector on the IO backplane. These ports accept RJ45 type cables.

VGA Connector

Chapter 2: Installation

GLAN1 GLAN2

A VGA connector (J16) is located between COM1 and GLAN1 on the IO backplane. Refer to the board layout below for the location.

A. GLAN1

B. GLAN2

C. VGA

C

A

B

2-19

Image 37

Contents X7SBL-LN1/LN2 Manual Revision 1.0c Release Date February 6 Manual Organization About This ManualConventions Used in the Manual Table of Contents Troubleshooting Bios Overview ChecklistEurope HeadquartersAsia-Paciﬁ c X7SBL-LN1/LN2 Image Important Notes to the User Motherboard LayoutJPUSB1/JPUSB2 X7SBL-LN1/LN2 Quick ReferenceMotherboard Features Temperature Acpi FeaturesDimensions Onboard I/OIntel 3200 Chipset System Block Diagram Block DiagramChipset Overview Intel ICH9R System FeaturesMemory Controller Hub MCH Environmental Temperature Control Special FeaturesRecovery from AC Power Loss PC Health MonitoringVirtualization Technology Acpi FeaturesCPU Overheat LED and Control System Resource AlertSuper I/O Slow Blinking LED for Suspend-State IndicatorPrecautions Motherboard InstallationStatic-Sensitive Devices UnpackingInstallation Overview Processor and Heatsink InstallationTriangle Installation of the LGA 775 ProcessorPage Installation of the Heatsink Removal of the Heatsink Dimm Installation Installing DIMMsMemory Support Top View of DDR2 Installing and Removing DIMMsBack Panel Connectors/IO Ports Control Panel Connectors/IO PortsBack Panel Connectors Back Panel I/O Port Locations and Deﬁ nitionsFront Control Panel Header PinsFront Control Panel Pin Deﬁ nitions NMI Button Power LEDHDD LED NIC1/NIC2 LED IndicatorsOverheat/Fan Fail LED OH Power Fail LEDPower Button Reset ButtonATX Power Connector Connecting CablesProcessor Power Connector Chassis Intrusion Universal Serial Bus USBSerial Ports ATX PS/2 Keyboard and PS/2 Mouse PortsPWR LED External Speaker/Internal BuzzerGlan Giga-bit Ethernet Ports VGA ConnectorFan Headers Wake-On-LAN Wake-On-RingPower SMB Connector Power Fault PWR Supply FailureGlan Enable/Disable Jumper SettingsExplanation of Jumpers Clear Cmos Watch Dog Enable/DisablePCI/PCI-E Slots to SMB Speeds VGA Enable/DisableForce-Power-On Enable/Disable USB Wake-Up Glan LEDs Onboard IndicatorsOnboard Power LED LE1 9Floppy and SIM 1U Ipmi Connections Floppy ConnectorSIM 1U Ipmi X7SBL-LN1/LN2 User’s Manual Before Power On Troubleshooting ProceduresNo Power Losing the System’s Setup Conﬁ guration Memory ErrorsNo Video Technical Support Procedures Question What type of memory does my motherboard support? Frequently Asked QuestionsReturning Merchandise for Service X7SBL-LN1/LN2 User’s Manual How To Change the Conﬁ guration Data System BiosStarting the Setup Utility IntroductionMain Bios Setup Running SetupSystem Time Main Bios Setup Menu ΥMain Setup FeaturesSystem Date Legacy Diskette aBios Revision Bios DateHard Disk Pre-Delay Native Mode OperationΥIDE Channel 0 Master/Slave/SATA Port2/SATA Port3 Sata Ahci Legacy EnableType CHS Format LBA Mode ControlLBA Format Multi-Sector TransfersUltra DMA Mode Transfer ModeInstalled Memory Bit I/OΥBoot Features Advanced SetupQuiet Boot QuickBoot ModeAcpi Mode Post ErrorsPower Button Behavior Resume On Modem RingΥAdvanced Processor Options Power Loss ControlWatch Dog Summary ScreenHyperthreading Available when supported by the CPU C1 Enhanced Mode Available when supported by the CPU Intel Virtualization Technology Available when supported bySet Maximum Ext. CPUID=3 Echo TPRΥAdvanced Chipset Control Clock Spectrum FeatureCPU and the OS High Precision Event Timer Enable VT-DMemory Remapping Route Port 80h Cycles toCache Video Bios Area Cache System Bios AreaΥMemory Cache Cache Base 0-512KΥPCI32 Slot#1 PCI32 Slot#2 ΥPNP Conﬁ gurationΥSlot 4 PCI-Exp ΥSlot 3 PCI-ExpΥI/O Device Conﬁ guration ΥOnboard LAN 1 and Onboard LANSerial Port a KBC Clock InputBase I/O Address InterruptΥDMI Event Logging ΥHardware Monitoring ΥConsole RedirectionCPU Overheat Alarm CPU Temperature Fan1 Fan System TemperatureFan Speed Control Modes Voltage Monitoring Security SettingsUser Password Is Supervisor Password IsSet Supervisor Password Set User PasswordBoot Priority Order/Excluded from Boot Orders Boot SettingsExit Load Setup DefaultsExit Saving Changes Exit Discarding ChangesSave Changes Discard ChangesPage Recoverable Post Error Beep Codes Appendix a Bios Error Beep CodesPage Appendix B Installing the Windows OS Page Appendix C Installing Other Software Programs and Drivers Conﬁ guring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Disclaimer