SUPER MICRO Computer X7SBL-LN1/LN2 user manual PCI/PCI-E Slots to SMB Speeds, VGA Enable/Disable

Page 43

Chapter 2: Installation

PCI/PCI-E Slots to SMB

Speeds

Jumpers JI2C1/JI2C2 allow you to connect PCI/PCI-Exp. Slots to the System Management Bus. The de- fault setting is open to disable the connection. See the table on the right for jumper settings.

VGA Enable/Disable

JPG1 enables or disables the VGA Connector on the motherboard. See the table on the right for jumper set- tings. The default setting is enabled.

CA

B

SMBus to PCI-X/PCI-Exp Slots

Jumper Settings

Jumper Setting		Deﬁ nition
Closed		Enabled
Closed		Enabled
Open		Disabled (*Default)
Open		Disabled (*Default)

	VGA Enable

Pin# Deﬁ nition
Pins 1-2		Enabled (*default)

Pins 2-3		Disabled

A.JI2C1

B.JI2C2

C.JPG1

2-25

Image 43

Contents X7SBL-LN1/LN2 Manual Revision 1.0c Release Date February 6 Manual Organization About This ManualConventions Used in the Manual Table of Contents Troubleshooting Bios Overview ChecklistEurope HeadquartersAsia-Paciﬁ c X7SBL-LN1/LN2 Image Important Notes to the User Motherboard LayoutJPUSB1/JPUSB2 X7SBL-LN1/LN2 Quick ReferenceMotherboard Features Onboard I/O Acpi FeaturesTemperature DimensionsIntel 3200 Chipset System Block Diagram Block DiagramChipset Overview Intel ICH9R System FeaturesMemory Controller Hub MCH PC Health Monitoring Special FeaturesEnvironmental Temperature Control Recovery from AC Power LossSystem Resource Alert Acpi FeaturesVirtualization Technology CPU Overheat LED and ControlSuper I/O Slow Blinking LED for Suspend-State IndicatorUnpacking Motherboard InstallationPrecautions Static-Sensitive DevicesInstallation Overview Processor and Heatsink InstallationTriangle Installation of the LGA 775 ProcessorPage Installation of the Heatsink Removal of the Heatsink Dimm Installation Installing DIMMsMemory Support Top View of DDR2 Installing and Removing DIMMsBack Panel I/O Port Locations and Deﬁ nitions Control Panel Connectors/IO PortsBack Panel Connectors/IO Ports Back Panel ConnectorsFront Control Panel Header PinsFront Control Panel Pin Deﬁ nitions NMI Button Power LEDHDD LED NIC1/NIC2 LED IndicatorsOverheat/Fan Fail LED OH Power Fail LEDPower Button Reset ButtonATX Power Connector Connecting CablesProcessor Power Connector Chassis Intrusion Universal Serial Bus USBSerial Ports ATX PS/2 Keyboard and PS/2 Mouse PortsPWR LED External Speaker/Internal BuzzerGlan Giga-bit Ethernet Ports VGA ConnectorFan Headers Wake-On-LAN Wake-On-RingPower SMB Connector Power Fault PWR Supply FailureGlan Enable/Disable Jumper SettingsExplanation of Jumpers Clear Cmos Watch Dog Enable/DisablePCI/PCI-E Slots to SMB Speeds VGA Enable/DisableForce-Power-On Enable/Disable USB Wake-Up Glan LEDs Onboard IndicatorsOnboard Power LED LE1 9Floppy and SIM 1U Ipmi Connections Floppy ConnectorSIM 1U Ipmi X7SBL-LN1/LN2 User’s Manual Before Power On Troubleshooting ProceduresNo Power Losing the System’s Setup Conﬁ guration Memory ErrorsNo Video Technical Support Procedures Question What type of memory does my motherboard support? Frequently Asked QuestionsReturning Merchandise for Service X7SBL-LN1/LN2 User’s Manual Introduction System BiosHow To Change the Conﬁ guration Data Starting the Setup UtilityMain Bios Setup Running SetupLegacy Diskette a Main Bios Setup Menu ΥMain Setup FeaturesSystem Time System DateNative Mode Operation Bios DateBios Revision Hard Disk Pre-DelayΥIDE Channel 0 Master/Slave/SATA Port2/SATA Port3 Sata Ahci Legacy EnableType Multi-Sector Transfers LBA Mode ControlCHS Format LBA FormatBit I/O Transfer ModeUltra DMA Mode Installed MemoryQuickBoot Mode Advanced SetupΥBoot Features Quiet BootResume On Modem Ring Post ErrorsAcpi Mode Power Button BehaviorSummary Screen Power Loss ControlΥAdvanced Processor Options Watch DogHyperthreading Available when supported by the CPU Echo TPR Intel Virtualization Technology Available when supported byC1 Enhanced Mode Available when supported by the CPU Set Maximum Ext. CPUID=3ΥAdvanced Chipset Control Clock Spectrum FeatureCPU and the OS Route Port 80h Cycles to Enable VT-DHigh Precision Event Timer Memory RemappingCache Base 0-512K Cache System Bios AreaCache Video Bios Area ΥMemory CacheΥPCI32 Slot#1 PCI32 Slot#2 ΥPNP Conﬁ gurationΥSlot 4 PCI-Exp ΥSlot 3 PCI-ExpΥI/O Device Conﬁ guration ΥOnboard LAN 1 and Onboard LANInterrupt KBC Clock InputSerial Port a Base I/O AddressΥDMI Event Logging ΥHardware Monitoring ΥConsole RedirectionCPU Overheat Alarm CPU Temperature Fan1 Fan System TemperatureFan Speed Control Modes Voltage Monitoring Security SettingsSet User Password Supervisor Password IsUser Password Is Set Supervisor PasswordBoot Priority Order/Excluded from Boot Orders Boot SettingsExit Discarding Changes Load Setup DefaultsExit Exit Saving ChangesSave Changes Discard ChangesPage Recoverable Post Error Beep Codes Appendix a Bios Error Beep CodesPage Appendix B Installing the Windows OS Page Appendix C Installing Other Software Programs and Drivers Conﬁ guring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Disclaimer