SUPER MICRO Computer AS1011M-T2 Connecting the Control Panel, Front Control Panel Header Pins JF1

Page 40

AS1011M-T2 User's Manual

Connecting the Control Panel

JF1 contains header pins for various front control panel connectors. See Figure 5-2 for the pin locations of the various front control panel buttons and LED indica- tors and refer to section 5-9 for details. Note that even and odd numbered pins are on opposite sides of each header.

All JF1 wires have been bundled into single keyed ribbon cable to simplify their connection. The red wire in the ribbon cable plugs into pin 1 of JF1. Connect the other end of the cable to the Control Panel printed circuit board, located just behind the system status LEDs in the chassis.

See the Connector Deﬁ nitions section in this chapter for details and pin descrip- tions of JF1.

Figure 5-2. Front Control Panel Header Pins (JF1)

20	19
Ground	NMI
x (key)	x (key)
Power LED	Vcc
HDD LED	Vcc
NIC1	Vcc
NIC2	Vcc
OH/Fan Fail LED	Vcc
Power Fail LED	Vcc
Ground	Reset Button
Ground	Power Button
2	1

5-6

Image 40

Contents AS1011M-T2 Manual Revision Release Date November 30 About This Manual PrefaceManual Organization System Safety Advanced Motherboard SetupAdvanced Chassis Setup BiosPreface Table of Contents Advanced Motherboard Setup HDD LED NIC1/NIC2 LEDAdvanced Chassis Setup SgpioBios AppendicesPage Chapter Introduction OverviewMotherboard Features Other Features Onboard Controllers/PortsServer Chassis Features System PowerControl Panel Rear I/O PanelContacting Supermicro HeadquartersEurope Asia-PaciﬁcPage Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Installing the System into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Motherboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Chapter System Interface Control Panel ButtonsControl Panel LEDs Serial ATA Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Motherboard Setup PrecautionsHandling the Motherboard UnpackingInstalling the Processor Processor and Heatsink InstallationMounting the Motherboard into a Chassis Installing the Heatsink Installing the Heatsink Retention Modules Removing the Air ShroudConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel Front Control Panel Header Pins JF1Installing Memory I/O PortsSide and Top Views of DDR Installation SupportAdding PCI Cards PCI card installationPCI slots Motherboard Details Super H8SMi-2Jumpers Description Default Setting Connectors DescriptionH8SMi-2 Quick Reference LEDs DescriptionConnector Deﬁnitions ATX Power ConnectorAuxiliary Power Connector Power LEDReset Button Power Fail LEDOverheat/Fan Fail LED Universal Serial Bus Ports JUSB1 Power ButtonUSB Headers ATX PS/2 Keyboard and PS/2 Mouse Ports Serial PortsFan Headers LAN1/2 Ethernet PortsPower LED/Speaker Overheat LEDChassis Intrusion Wake-On-LANRedundant Power Supply Fail Header Wake-On-RingSMBus Header UID LED HeaderPower Fail Alarm Reset Header Compact Flash PowerExplanation Jumpers Jumper SettingsCmos Clear I2C to PCI Enable/Disable VGA Enable/DisableWatch Dog Onboard Speaker Enable/ Disable USB PowerPS2 Power Compact Flash Master/SlaveOnboard Power LED Onboard IndicatorsLAN1/LAN2 LEDs Floppy Connector Floppy, IDE, Parallel Port and Sata Drive ConnectionsIDE Connector Sata PortsParallel Port Parallel Printer Port Pin DeﬁnitionsInstalling the OS/SATA Driver Enabling Sata RAID in the BiosEnabling Sata RAID Serial ATA SataUsing the nVidia RAID Utility Installing the OS and DriversInstalling Drivers Driver/Tool Installation Display ScreenChapter Advanced Chassis Setup PrecautionsStatic-Sensitive Devices Tools RequiredControl Panel Chassis Front ViewInstalling a new fan System FansSystem Fan Failure Replacing System FansDrive Bay Installation/Removal Accessing the Drive BaysSerial ATA Drive Installation Mounting a Serial ATA drive in a drive carrierInstalling/removing hot-swap Serial ATA drives CD-ROM and Floppy Drive Installation Serial ATA BackplanePower Supply Power Supply FailureReplacing the Power Supply Removing the power supplyPage Chapter Starting the Setup UtilityIntroduction Boot Features Advanced Settings MenuMain Menu Wait for ‘F1’ If Error Acpi Version FeaturesAcpi Settings Acpi Apic Support Headless ModeCPU Conﬁguration Floppy/IDE/SATA Conﬁguration LBA/Large Mode Primary IDE Master/SlaveType Block Multi-Sector TransferDMA Mode A.R.TBit Data Transfer Serial ATA0/1/2 Primary/Secondary ChannelIDE Detect Time Out Sec Hard Disk Write ProtectAtapi 80Pin Cable Detection PCI/PnP Conﬁguration Super IO Conﬁguration Advanced Chipset Conﬁguration NorthBridge ConﬁgurationSouthBridge/MCP55 Conﬁguration USB 2.0 Controller Mode Bios Ehci Hand-OffPcie Spread Spectrum Sata Spread SpectrumRemote Access Conﬁguration Event Log ConﬁgurationSystem Health Monitor View BMC System Event Log Clear BMC System Event LogSet LAN Conﬁguration IP AddressBoot Menu Boot Device PriorityHard Disk Drives Removable DrivesSecurity Menu Exit MenuLoad Optimal Defaults Load Fail-Safe DefaultsPage Amibios Error Beep Codes Appendix a Bios Error Beep CodesBeep Code Error Message Description Page Appendix B Bios Post Checkpoint Codes Uncompressed Initialization CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Appendix C System Speciﬁcations Weight Power SupplyMotherboard ChassisRegulatory Compliance