SUPER MICRO Computer AS1011M-T2 user manual Primary IDE Master/Slave, Type, LBA/Large Mode

Page 76

AS1011M-T2 User's Manual

Primary IDE Master/Slave

Highlight one of the items above and press <Enter> to access the submenu for that item.

Type

Select the type of device connected to the system. The options are Not Installed, Auto, CDROM and ARMD.

LBA/Large Mode

LBA (Logical Block Addressing) is a method of addressing data on a disk drive. The options are Disabled and Auto.

Block (Multi-Sector Transfer)

Block mode boosts IDE drive performance by increasing the amount of data transferred. Only 512 bytes of data can be transferred per interrupt if block mode is not used. Block mode allows transfers of up to 64 KB per interrupt. Select "Disabled" to allow the data to be transferred from and to the device one sec- tor at a time. Select "Auto" to allows the data transfer from and to the device occur multiple sectors at a time if the device supports it. The options are Auto and Disabled.

PIO Mode

PIO (Programmable I/O) mode programs timing cycles between the IDE drive and the programmable IDE controller. As the PIO mode increases, the cycle time decreases. The options are Auto, 0, 1, 2, 3, and 4. Select Auto to allow AMI BIOS to auto detect the PIO mode. Use this value if the IDE disk drive support cannot be determined. Select 0 to allow AMI BIOS to use PIO mode 0. It has a data transfer rate of 3.3 MBs. Select 1 to allow AMI BIOS to use PIO mode 1. It has a data transfer rate of 5.2 MBs. Select 2 to allow AMI BIOS to use PIO mode 2. It has a data transfer rate of 8.3 MBs. Select 3 to allow AMI BIOS to use PIO mode 3. It has a data transfer rate of 11.1 MBs. Select 4 to allow AMI BIOS to use PIO mode 4. It has a data transfer rate of 16.6 MBs. This setting generally works with all hard disk drives manufactured after 1999. For other disk drives, such as IDE CD-ROM drives, check the specifi cations of the drive.

7-6

Image 76
Contents AS1011M-T2 Manual Revision Release Date November 30 About This Manual PrefaceManual Organization System Safety Advanced Motherboard SetupAdvanced Chassis Setup BiosPreface Table of Contents Advanced Motherboard Setup HDD LED NIC1/NIC2 LEDAdvanced Chassis Setup SgpioBios AppendicesPage Chapter Introduction OverviewMotherboard Features Other Features Onboard Controllers/PortsServer Chassis Features System PowerControl Panel Rear I/O PanelContacting Supermicro HeadquartersEurope Asia-PacificPage Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Installing the System into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Motherboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Chapter System Interface Control Panel ButtonsControl Panel LEDs Serial ATA Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Motherboard Setup PrecautionsHandling the Motherboard UnpackingInstalling the Processor Processor and Heatsink InstallationMounting the Motherboard into a Chassis Installing the Heatsink Installing the Heatsink Retention Modules Removing the Air ShroudConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel Front Control Panel Header Pins JF1Installing Memory I/O PortsSide and Top Views of DDR Installation SupportAdding PCI Cards PCI card installationPCI slots Motherboard Details Super H8SMi-2Jumpers Description Default Setting Connectors DescriptionH8SMi-2 Quick Reference LEDs DescriptionConnector Definitions ATX Power ConnectorAuxiliary Power Connector Power LEDReset Button Power Fail LEDOverheat/Fan Fail LED Universal Serial Bus Ports JUSB1 Power ButtonUSB Headers ATX PS/2 Keyboard and PS/2 Mouse Ports Serial PortsFan Headers LAN1/2 Ethernet PortsPower LED/Speaker Overheat LEDChassis Intrusion Wake-On-LANRedundant Power Supply Fail Header Wake-On-RingSMBus Header UID LED HeaderPower Fail Alarm Reset Header Compact Flash PowerExplanation Jumpers Jumper SettingsCmos Clear I2C to PCI Enable/Disable VGA Enable/DisableWatch Dog Onboard Speaker Enable/ Disable USB PowerPS2 Power Compact Flash Master/SlaveOnboard Power LED Onboard IndicatorsLAN1/LAN2 LEDs Floppy Connector Floppy, IDE, Parallel Port and Sata Drive ConnectionsIDE Connector Sata PortsParallel Port Parallel Printer Port Pin DefinitionsInstalling the OS/SATA Driver Enabling Sata RAID in the BiosEnabling Sata RAID Serial ATA SataUsing the nVidia RAID Utility Installing the OS and DriversInstalling Drivers Driver/Tool Installation Display ScreenChapter Advanced Chassis Setup PrecautionsStatic-Sensitive Devices Tools RequiredControl Panel Chassis Front ViewInstalling a new fan System FansSystem Fan Failure Replacing System FansDrive Bay Installation/Removal Accessing the Drive BaysSerial ATA Drive Installation Mounting a Serial ATA drive in a drive carrierInstalling/removing hot-swap Serial ATA drives CD-ROM and Floppy Drive Installation Serial ATA BackplanePower Supply Power Supply FailureReplacing the Power Supply Removing the power supplyPage Chapter Starting the Setup UtilityIntroduction Boot Features Advanced Settings MenuMain Menu Wait for ‘F1’ If Error Acpi Version FeaturesAcpi Settings Acpi Apic Support Headless ModeCPU Configuration Floppy/IDE/SATA Configuration LBA/Large Mode Primary IDE Master/SlaveType Block Multi-Sector TransferDMA Mode A.R.TBit Data Transfer Serial ATA0/1/2 Primary/Secondary ChannelIDE Detect Time Out Sec Hard Disk Write ProtectAtapi 80Pin Cable Detection PCI/PnP Configuration Super IO Configuration Advanced Chipset Configuration NorthBridge ConfigurationSouthBridge/MCP55 Configuration USB 2.0 Controller Mode Bios Ehci Hand-OffPcie Spread Spectrum Sata Spread SpectrumRemote Access Configuration Event Log ConfigurationSystem Health Monitor View BMC System Event Log Clear BMC System Event LogSet LAN Configuration IP AddressBoot Menu Boot Device PriorityHard Disk Drives Removable DrivesSecurity Menu Exit MenuLoad Optimal Defaults Load Fail-Safe DefaultsPage Amibios Error Beep Codes Appendix a Bios Error Beep CodesBeep Code Error Message Description Page Appendix B Bios Post Checkpoint Codes Uncompressed Initialization CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Appendix C System Specifications Weight Power SupplyMotherboard ChassisRegulatory Compliance