SUPER MICRO Computer AS1011M-T2 user manual I/O Ports, Installing Memory

Page 41

Chapter 5: Advanced Motherboard Setup

5-5 I/O Ports

The I/O ports are color coded in conformance with the PC 99 specifi cation. See Figure 5-3 below for the colors and locations of the various I/O ports.

Figure 5-3. Rear Panel I/O Ports

5-6 Installing Memory

CAUTION

Exercise extreme care when installing or removing memory modules

to prevent any possible damage.

1.Insert each memory module vertically into its slot, paying attention to the notch along the bottom of the module to prevent inserting the module incorrectly (see Figure 2-2). Install to slot 1A fi rst, then 2A, etc. See support information below.

2.Gently press down on the memory module until it snaps into place.

Note: 256 MB, 512 MB, 1 GB and 2 GB memory modules are supported. It is highly recommended that you remove the power cord from the system before installing or changing any memory modules.

5-7

Image 41
Contents AS1011M-T2 Manual Revision Release Date November 30 Manual Organization PrefaceAbout This Manual Advanced Motherboard Setup System SafetyAdvanced Chassis Setup BiosPreface Table of Contents HDD LED NIC1/NIC2 LED Advanced Motherboard SetupSgpio Advanced Chassis SetupAppendices BiosPage Overview Chapter IntroductionMotherboard Features Onboard Controllers/Ports Other FeaturesSystem Power Server Chassis FeaturesControl Panel Rear I/O PanelHeadquarters Contacting SupermicroEurope Asia-PacificPage Unpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Rack Mounting Considerations Identifying the Sections of the Rack Rails Installing the System into a RackInstalling the Rack Rails Installing the Chassis RailsInstalling the Server into a Rack Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Motherboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Control Panel Buttons Chapter System InterfaceControl Panel LEDs Serial ATA Drive Carrier LEDs Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsPrecautions Chapter Advanced Motherboard SetupHandling the Motherboard UnpackingMounting the Motherboard into a Chassis Processor and Heatsink InstallationInstalling the Processor Installing the Heatsink Removing the Air Shroud Installing the Heatsink Retention ModulesConnecting Power Cables Connecting CablesConnecting Data Cables Front Control Panel Header Pins JF1 Connecting the Control PanelI/O Ports Installing MemorySupport Side and Top Views of DDR InstallationPCI slots PCI card installationAdding PCI Cards Super H8SMi-2 Motherboard DetailsConnectors Description Jumpers Description Default SettingH8SMi-2 Quick Reference LEDs DescriptionATX Power Connector Connector DefinitionsAuxiliary Power Connector Power LEDOverheat/Fan Fail LED Power Fail LEDReset Button USB Headers Power ButtonUniversal Serial Bus Ports JUSB1 Serial Ports ATX PS/2 Keyboard and PS/2 Mouse PortsFan Headers LAN1/2 Ethernet PortsOverheat LED Power LED/SpeakerChassis Intrusion Wake-On-LANWake-On-Ring Redundant Power Supply Fail HeaderSMBus Header UID LED HeaderCompact Flash Power Power Fail Alarm Reset HeaderCmos Clear Jumper SettingsExplanation Jumpers Watch Dog VGA Enable/DisableI2C to PCI Enable/Disable USB Power Onboard Speaker Enable/ DisablePS2 Power Compact Flash Master/SlaveLAN1/LAN2 LEDs Onboard IndicatorsOnboard Power LED Floppy, IDE, Parallel Port and Sata Drive Connections Floppy ConnectorSata Ports IDE ConnectorParallel Printer Port Pin Definitions Parallel PortEnabling Sata RAID in the Bios Installing the OS/SATA DriverEnabling Sata RAID Serial ATA SataInstalling the OS and Drivers Using the nVidia RAID UtilityDriver/Tool Installation Display Screen Installing DriversPrecautions Chapter Advanced Chassis SetupStatic-Sensitive Devices Tools RequiredChassis Front View Control PanelSystem Fans Installing a new fanSystem Fan Failure Replacing System FansAccessing the Drive Bays Drive Bay Installation/RemovalSerial ATA Drive Installation Mounting a Serial ATA drive in a drive carrierInstalling/removing hot-swap Serial ATA drives Serial ATA Backplane CD-ROM and Floppy Drive InstallationPower Supply Failure Power SupplyReplacing the Power Supply Removing the power supplyPage Introduction Starting the Setup UtilityChapter Main Menu Advanced Settings MenuBoot Features Acpi Version Features Wait for ‘F1’ If ErrorAcpi Settings Acpi Apic Support Headless ModeCPU Configuration Floppy/IDE/SATA Configuration Primary IDE Master/Slave LBA/Large ModeType Block Multi-Sector TransferA.R.T DMA ModeBit Data Transfer Serial ATA0/1/2 Primary/Secondary ChannelAtapi 80Pin Cable Detection Hard Disk Write ProtectIDE Detect Time Out Sec PCI/PnP Configuration Super IO Configuration NorthBridge Configuration Advanced Chipset ConfigurationSouthBridge/MCP55 Configuration Bios Ehci Hand-Off USB 2.0 Controller ModePcie Spread Spectrum Sata Spread SpectrumEvent Log Configuration Remote Access ConfigurationSystem Health Monitor Clear BMC System Event Log View BMC System Event LogSet LAN Configuration IP AddressBoot Device Priority Boot MenuHard Disk Drives Removable DrivesExit Menu Security MenuLoad Fail-Safe Defaults Load Optimal DefaultsPage Beep Code Error Message Description Appendix a Bios Error Beep CodesAmibios Error Beep Codes Page Uncompressed Initialization Codes Appendix B Bios Post Checkpoint CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Appendix C System Specifications Power Supply WeightMotherboard ChassisRegulatory Compliance