SUPER MICRO Computer AS1011M-T2 user manual DMA Mode, A.R.T, Bit Data Transfer

Page 77

Chapter 7: BIOS

DMA Mode

Selects the DMA Mode. Options are Auto, SWDMA0, SWDMA1, SWDMA2, MWDMA0. MDWDMA1, MWDMA2, UDMA0. UDMA1, UDMA2, UDMA3, UDMA4 and UDMA5. (SWDMA=Single Word DMA, MWDMA=Multi Word DMA, UDMA=UltraDMA.)

S.M.A.R.T.

Self-Monitoring Analysis and Reporting Technology (SMART) can help predict impending drive failures. Select "Auto" to allow BIOS to auto detect hard disk drive support. Select "Disabled" to prevent AMI BIOS from using the S.M.A.R.T. Select "Enabled" to allow AMI BIOS to use the S.M.A.R.T. to support hard drive disk. The options are Disabled, Enabled, and Auto.

32-Bit Data Transfer

Select "Enabled" to activate the function of 32-Bit data transfer. Select "Disabled" to deactivate the function. The options are Enabled and Disabled.

Serial ATA0/1/2 Primary/Secondary Channel

Highlight one of the items above and press <Enter> to access the submenu for that item. If a drive is present, information on that drive will be displayed here, including the following.

LBA/Large Mode

LBA (Logical Block Addressing) is a method of addressing data on a disk drive. The options are Disabled and Auto.

Block (Multi-Sector Transfer)

Block mode boosts IDE drive performance by increasing the amount of data transferred. Only 512 bytes of data can be transferred per interrupt if block mode is not used. Block mode allows transfers of up to 64 KB per interrupt. Select "Disabled" to allow the data to be transferred from and to the device one sec- tor at a time. Select "Auto" to allows the data transfer from and to the device occur multiple sectors at a time if the device supports it. The options are Auto and Disabled.

PIO Mode

PIO (Programmable I/O) mode programs timing cycles between the IDE drive and the programmable IDE controller. As the PIO mode increases, the cycle time decreases. The options are Auto, 0, 1, 2, 3, and 4. Select Auto to allow AMI BIOS to auto detect the PIO mode. Use this value if the IDE disk drive support

7-7

Image 77
Contents AS1011M-T2 Manual Revision Release Date November 30 Manual Organization PrefaceAbout This Manual Advanced Motherboard Setup System SafetyAdvanced Chassis Setup BiosPreface Table of Contents HDD LED NIC1/NIC2 LED Advanced Motherboard SetupSgpio Advanced Chassis SetupAppendices BiosPage Overview Chapter IntroductionMotherboard Features Onboard Controllers/Ports Other FeaturesSystem Power Server Chassis FeaturesControl Panel Rear I/O PanelHeadquarters Contacting SupermicroEurope Asia-PacificPage Unpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Rack Mounting Considerations Identifying the Sections of the Rack Rails Installing the System into a RackInstalling the Rack Rails Installing the Chassis RailsInstalling the Server into a Rack Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Motherboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Control Panel Buttons Chapter System InterfaceControl Panel LEDs Serial ATA Drive Carrier LEDs Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsPrecautions Chapter Advanced Motherboard SetupHandling the Motherboard UnpackingMounting the Motherboard into a Chassis Processor and Heatsink InstallationInstalling the Processor Installing the Heatsink Removing the Air Shroud Installing the Heatsink Retention ModulesConnecting Power Cables Connecting CablesConnecting Data Cables Front Control Panel Header Pins JF1 Connecting the Control PanelI/O Ports Installing MemorySupport Side and Top Views of DDR InstallationPCI slots PCI card installationAdding PCI Cards Super H8SMi-2 Motherboard DetailsConnectors Description Jumpers Description Default SettingH8SMi-2 Quick Reference LEDs DescriptionATX Power Connector Connector DefinitionsAuxiliary Power Connector Power LEDOverheat/Fan Fail LED Power Fail LEDReset Button USB Headers Power ButtonUniversal Serial Bus Ports JUSB1 Serial Ports ATX PS/2 Keyboard and PS/2 Mouse PortsFan Headers LAN1/2 Ethernet PortsOverheat LED Power LED/SpeakerChassis Intrusion Wake-On-LANWake-On-Ring Redundant Power Supply Fail HeaderSMBus Header UID LED HeaderCompact Flash Power Power Fail Alarm Reset HeaderCmos Clear Jumper SettingsExplanation Jumpers Watch Dog VGA Enable/DisableI2C to PCI Enable/Disable USB Power Onboard Speaker Enable/ DisablePS2 Power Compact Flash Master/SlaveLAN1/LAN2 LEDs Onboard IndicatorsOnboard Power LED Floppy, IDE, Parallel Port and Sata Drive Connections Floppy ConnectorSata Ports IDE ConnectorParallel Printer Port Pin Definitions Parallel PortEnabling Sata RAID in the Bios Installing the OS/SATA DriverEnabling Sata RAID Serial ATA SataInstalling the OS and Drivers Using the nVidia RAID UtilityDriver/Tool Installation Display Screen Installing DriversPrecautions Chapter Advanced Chassis SetupStatic-Sensitive Devices Tools RequiredChassis Front View Control PanelSystem Fans Installing a new fanSystem Fan Failure Replacing System FansAccessing the Drive Bays Drive Bay Installation/RemovalSerial ATA Drive Installation Mounting a Serial ATA drive in a drive carrierInstalling/removing hot-swap Serial ATA drives Serial ATA Backplane CD-ROM and Floppy Drive InstallationPower Supply Failure Power SupplyReplacing the Power Supply Removing the power supplyPage Introduction Starting the Setup UtilityChapter Main Menu Advanced Settings MenuBoot Features Acpi Version Features Wait for ‘F1’ If ErrorAcpi Settings Acpi Apic Support Headless ModeCPU Configuration Floppy/IDE/SATA Configuration Primary IDE Master/Slave LBA/Large ModeType Block Multi-Sector TransferA.R.T DMA ModeBit Data Transfer Serial ATA0/1/2 Primary/Secondary ChannelAtapi 80Pin Cable Detection Hard Disk Write ProtectIDE Detect Time Out Sec PCI/PnP Configuration Super IO Configuration NorthBridge Configuration Advanced Chipset ConfigurationSouthBridge/MCP55 Configuration Bios Ehci Hand-Off USB 2.0 Controller ModePcie Spread Spectrum Sata Spread SpectrumEvent Log Configuration Remote Access ConfigurationSystem Health Monitor Clear BMC System Event Log View BMC System Event LogSet LAN Configuration IP AddressBoot Device Priority Boot MenuHard Disk Drives Removable DrivesExit Menu Security MenuLoad Fail-Safe Defaults Load Optimal DefaultsPage Beep Code Error Message Description Appendix a Bios Error Beep CodesAmibios Error Beep Codes Page Uncompressed Initialization Codes Appendix B Bios Post Checkpoint CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Appendix C System Specifications Power Supply WeightMotherboard ChassisRegulatory Compliance