SUPER MICRO Computer AS 1020C-3 user manual Control Panel LEDs

Page 28

AS1020C-3 User's Manual

3-3 Control Panel LEDs

The control panel located on the front of th SC813TQ+-500 chassis has ﬁ ve LEDs. These LEDs provide you with critical information related to different parts of the system. This section explains what each LED indicates when illuminated and any corrective action you may need to take.

Overheat/Fan Fail: When this LED ﬂ ashes it indicates a fan failure. When on continuously (on and not ﬂ ashing) it indicates an overheat condition, which may be caused by cables obstructing the airﬂ ow in the system or the ambient room temperature being too warm. Check the routing of the cables and make sure all fans are present and operating normally. You should also check to make sure that the chassis covers are installed. Finally, verify that the heatsinks are installed properly (see Chapter 5). This LED will remain ﬂ ashing or on as long as the overheat condition exists.

2

NIC2: Indicates network activity on GLAN2 when ﬂ ashing .

1

NIC1: Indicates network activity on GLAN1 when ﬂ ashing.

3-2

Image 28

Contents AS 1020C-3 Manual Revision Release Date October 13 About This Manual PrefaceManual Organization System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Safety Advanced Serverboard SetupAdvanced Chassis Setup PssmbusBios AppendicesPage Chapter Introduction OverviewServerboard Features ProcessorsMemory SAS Serial Attached ScsiATI Graphics Controller Other FeaturesOnboard Controllers/Ports Server Chassis Features System PowerSerial Attached Scsi SAS Subsystem Control PanelNVidia nForce Pro 2200/AMD-8132 Chipset System Block Diagram Cooling SystemContacting Supermicro HeadquartersEurope Asia-PaciﬁcPreparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Installing the Rack Rails Installing the System into a RackIdentifying the Sections of the Rails Installing the Chassis Rails Identifying the Sections of the RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Serverboard Setup Checking the Drive Bay Setup Accessing the drive baysCD-ROM and ﬂoppy disk drives Check the SAS disk drivesSupplying power to the system Check the airﬂowChapter System Interface Control Panel ButtonsControl Panel LEDs SAS Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Serverboard Setup PrecautionsHandling the Serverboard UnpackingMounting the Serverboard into a Chassis Processor and Heatsink InstallationCPU Backplates Installing the Processor Is not recommendedInstalling the Heatsinks Installing HeatsinksConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel Front Control Panel Header Pins JF1I/O Ports Installing MemorySupport Optimizing memory performance Maximum memory two CPUsAdding PCI Cards PCI card installationPCI slots Serverboard Details H8DCR-3 Serverboard LayoutJumpers Description Default Setting Connectors DescriptionOnboard Indicators Description H8DCR-3 Quick ReferenceConnector Deﬁnitions ATX Power ConnectorProcessor Power Connector Auxiliary Power ConnectorPower LED Overheat/Fan Fail LEDReset Button Power ButtonLAN1/2 Ethernet Ports Universal Serial Bus Ports USB0/1Extra USB Headers Serial PortsFan Headers Chassis IntrusionATX PS/2 Keyboard and PS/2 Mouse Ports Power LED/SpeakerOverheat LED Alarm Reset Header Wake-On-LANWake-On-Ring SMBus HeaderPower Fail Connector Compact Flash Power ConnectorI2C for SAS Connector JSLED1 HeaderExplanation Jumpers Jumper SettingsCmos Clear 3rd Power Supply Fail Signal Enable/Disable I2C to PCI Enable/DisableVGA Enable/Disable Compact Flash Master/SlaveOnboard Speaker Enable/ Disable Watch Dog Enable/DisableSAS Controller Enable Disable LAN1/2 Enable/Disable PCI-X Slot Frequency SelectOnboard Indicators LAN1/LAN2 LEDs+3.3V Standby LED SAS Activity LEDsFloppy Connector Floppy, IDE and SAS ConnectionsIDE Connectors SAS PortsSerial Attached Scsi SAS Enabling SAS RAIDEnabling SAS RAID SAS Controller Utility Creating a RAID ArrayArray Conﬁguration Utility Screen Additional Functions Selecting Drives for the ArrayInstalling Drivers 10. Driver/Tool Installation Display ScreenStatic-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front and Rear ViewsInstalling a new fan System FansSystem Fan Failure Replacing System Cooling FansDrive Bay Installation/Removal Removing the Front BezelAccessing the Drive Bays Removing the Front BezelSerial Attached Scsi SAS Drive Installation Mounting a SAS drive in a drive carrierInstalling/removing hot-swap SAS drives SAS BackplaneCD-ROM and Floppy Drive Installation Power Supply Power Supply FailureRemoving/Replacing the Power Supply Removing the power supplyRemoving/Replacing the Power Supply Chapter Starting the Setup UtilityIntroduction Advanced Settings Menu Main MenuCPU Conﬁguration IDE ConﬁgurationLBA/Large Mode Primary/Secondary IDE Master/SlaveType Block Multi-Sector TransferDMA Mode First Boot Device FromA.R.T Bit Data TransferConﬁguration nVidia RAID ROM PCI/PnP MenuFloppy Conﬁguration Advanced Chipset Control NorthBridge ConﬁgurationUser Conﬁg Mode ECC Conﬁguration Dram ECC EnableBank Interleaving Burst LengthSouthBridge Conﬁguration Device Conﬁguration Hyper Transport Conﬁguration DMI Event Logging AMD PowerNow ConﬁgurationConsole Redirection System Health Monitor Ipmi 1.5 ConﬁgurationAlert Startup Delay Startup DelayCbmc Watch Dog Timer Action Set LAN Conﬁguration IP AddressUSB 2.0 Controller Mode Bios Ehci Hand-OffUSB Conﬁguration USB Controller SupportBoot Menu Boot Settings ConﬁgurationBoot Device Priority OS InstallationSecurity Menu Removeable DrivesExit Menu Page Amibios Error Beep Codes Appendix a Bios Error Beep CodesBeep Code Error Message Description AS1020C-3 User’s Manual Appendix B Bios Post Checkpoint Codes Uncompressed Initialization CodesBootblock Recovery Codes Uncompressed Initialization Codes AS1020C-3 User’s Manual Appendix B Bios Post Checkpoint Codes AS1020C-3 User’s Manual A9h Aah Abh B0h B1h 00h AS1020C-3 User’s Manual Appendix C System Speciﬁcations Weight Power SupplyServerboard ChassisRegulatory Compliance