SUPER MICRO Computer 5017C-MTRF, 5017C-MTF manual Fan Headers, Chassis Intrusion, External Speaker

Page 48

SUPERSERVER 5017C-MTF/5017C-MTRF User's Manual

Fan Headers

The X9SCL-F has five fan headers (Fan1

~Fan4 and FanA). These are all 4-pin fan headers, however pins 1-3 are backward compatible with traditional 3-pin fans. A fan speed control setting in the BIOS (Hardware Monitoring section) allows the BIOS to automatically set fan speeds based on the system temperature. Refer to the table on the right for pin defini- tions.

Note: Please use all 3-pin fans or all 4-pin fans on a motherboard. Do not mix 3-pin fans and 4-pin fans on the same board.

Chassis Intrusion

A Chassis Intrusion header is located at JL1 on the motherboard. Attach the ap- propriate cable from the chassis to inform you of a chassis intrusion when the chas- sis is opened.

ATX PS/2 Keyboard and PS/2 Mouse Ports

The ATX PS/2 keyboard and the PS/2 mouse ports are located beside the USB ports. See the table on the right for pin definitions.

External Speaker

On the JSPK header, pins 3~4 are used to activate the onboard (internal) speaker. Close pins 3~4 with a jumper to use the onboard speaker. If you wish to use an external speaker, attach the external speaker's cable to pins 1~4. See the table on the right for pin definitions.

Fan Header

Pin Definitions

Pin# Definition

1Ground (Black)

22.5A/+12V (Red)

3Tachometer

4PWM_Control

Chassis Intrusion

Pin Definitions

Pin# Definition

1Intrusion Input

2Ground

PS/2 Keyboard and

Mouse Ports

Pin Definitions

Pin# Definition

1Data

2NC

3Ground

4VCC

5Clock

6NC

Speaker Connector

Pin Definitions

Pin Setting

 

Definition

Pins 3~4

 

Internal Speaker

 

Pins1~4

 

External Speaker

 

 

 

 

5-16

Image 48
Contents Super Manual Revision 1.0c Release Date January 2 Preface About This ManualManual Organization System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Interface Advanced Chassis Setup Chapter Introduction OverviewMotherboard Features Server Chassis Features Intel C200 Chipset System Block Diagram Contacting Supermicro HeadquartersEurope Asia-PacificPage Chapter Server Installation Preparing for SetupChoosing a Setup Location Unpacking the SystemRack Precautions Server PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsInstalling the System into a Rack Installing the Rear Inner RailsIdentifying the Sections of the Rack Rails Installing the Rack Rails Installing Rear Inner Chassis RailsInstalling the Server into the Rack Installing the Server into a Telco Rack Checking the Motherboard Setup Accessing the Inside of the SystemChecking the Components Checking the Drive Bay Setup Accessing the Inside of the SystemChecking the Drives Providing Power Checking the AirflowReset PowerChapter System Interface Control Panel ButtonsControl Panel LEDs Overheat/Fan FailHard Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Motherboard Setup Processor and Heatsink Installation Installing the LGA1155 ProcessorPage Installing a Passive CPU Heatsink Removing the HeatsinkInstalling the Heatsink Connecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control PanelFront Control Panel Header Pins JF1 I/O PortsInstalling Memory Installing DIMMsMemory Support DDR3 Unbuffered ECC Udimm MemoryInstalling Dimm into Slot Possible System Memory Allocation & AvailabilityPCI Card Installation Adding PCI CardsPCI Expansion Slots PCI Slot/Card ConfigurationsNumber Jumper Description Default Motherboard DetailsJumpers Headers/Connectors LED IndicatorsNumber Connector Description NumberConnector Definitions ATX Power ConnectorProcessor Power Connector Power LEDReset Button Power ButtonOverheat OH/Fan Fail/Front UID LED Universal Serial Bus USB Serial PortsEthernet Ports Fan Headers Chassis IntrusionATX PS/2 Keyboard and PS/2 Mouse Ports External SpeakerOnboard Power LED Power Supply I2C ConnectorTrusted Platform Module Header Wake-On-LANDOM PWR Connector Sgpio 0/1 HeadersSgpio 1/2 Headers Jumper Settings VGA Enable/DisableExplanation of Jumpers Cmos ClearPCI Slot SMB Enable LAN Port Enable/DisableBMC Enable/Disable Watch Dog EnableOnboard Indicators Onboard Standby Power LEDLAN1/LAN2 LEDs Ipmi Dedicated LANSata Drive Connections Sata PortsInstalling Drivers Driver Installation Display ScreenSuperDoctor SuperDoctor III Interface Display Screen Health InformationSuperDoctor III Interface Display Screen Remote Control Page Chapter Advanced Chassis Setup Control Panel Chassis Front ViewDrive Bay Installation/Removal System FansSystem Fan Failure Removing the Front BezelAccessing the Drive Bays Sata Drive InstallationInstalling/Removing Sata Drives Mounting a Drive in a Drive CarrierSata Backplane Mounting a Drive in a CarrierDVD-ROM Drive Installation Removing/Installing a DriveRemoving the Chassis Cover Power Supply Power Supply FailureReplacing the Power Supply Removing the Power Supply Starting Bios Setup Utility How To Change the Configuration DataChapter IntroductionMain Setup How to Start the Setup UtilitySystem Time/System Date ProcessorSystem Memory Advanced Setup Configurations BOOT FeatureProcessor & Clock Options Power Technology Intel AES-NIIntel Hyper Threading Technology Active Processor CoresChipset Configuration Active State Power Management North Bridge ConfigurationVT-d Pcie Maximum Payload SizeIDE/SATA Configuration PCIe/PCI/PnP Configuration Super IO Device Configuration Remote Access Configuration Serial Port 2 ModeConsole Redirection Settings COM0/COM1/SOL Console RedirectionFan Speed Control Mode CPU Temperature Display ModeHardware Health Configuration ACPI Configuration Smbios Event Log When Log is FullEvent Logs Erase Event LogIpmi Configuration When SEL Full Log EFI Status CodesView FRU Information BMC Network ConfigurationBoot Settings Boot Options PriorityBoot Option #1, Boot option #2, Boot Option #3, etc Security Settings Administrator PasswordUser Password Boot Sector Virus ProtectionRestore Defaults Exit OptionsSave Changes and Exit Discard Changes and ExitSave As User Defaults Restore User DefaultsBoot Override Page Appendix a Bios Error Beep Codes Bios Error Beep CodesBios Error Beep Codes Error MessagePage Appendix B System Specifications Weight Power SupplySystem Cooling System Input RequirementsRegulatory Compliance

5017C-MTRF, 5017C-MTF specifications

Supermicro Computer has established itself as a leader in high-performance server solutions, and the Supermicro 5017C-MTF and 5017C-MTRF models exemplify the company's commitment to quality and innovation. These compact systems are designed for diverse applications, catering to both small and medium-sized enterprises as well as larger organizational needs.

The Supermicro 5017C-MTF and 5017C-MTRF come equipped with a powerful Intel Xeon E3-1200 v6 processor, offering remarkable processing capabilities that enable users to run demanding applications with ease. These systems support up to 64GB of ECC DDR4 memory, ensuring data integrity and reliability crucial for mission-critical workloads. Moreover, the implementations of Intel's turbo boost technology allow for dynamic performance enhancements, enabling processors to scale up in speed as workload demands increase.

These models highlight Supermicro's commitment to flexibility and expandability. Both the 5017C-MTF and 5017C-MTRF include multiple PCIe slots so users can integrate various expansion cards according to their requirements. Additionally, the dual Gigabit Ethernet ports enhance networking capabilities, supporting multiple connectivity options to meet organizational demands.

Storage is an important aspect of any server solution, and these models do not disappoint. They offer support for multiple SATA drives and come with options for SSD integration for high-speed data access. This makes the 5017C-MTF and 5017C-MTRF well-suited for virtualization, cloud storage solutions, or even as a database server.

The systems also boast a compact and energy-efficient design, making them ideal for space-constrained environments. The 1U rackmount form factor allows for easy deployment in data center settings, while also promoting efficient airflow and cooling design. Furthermore, both models meet stringent energy efficiency standards, which can lead to significant power savings over time.

Security and remote management features are also key highlights of the 5017C-MTF and 5017C-MTRF. Supermicro’s Intelligent Management Technology (IMT) software allows administrators to monitor system health remotely and perform management tasks effectively.

In summary, the Supermicro 5017C-MTF and 5017C-MTRF present robust server solutions packed with cutting-edge technology, flexible expansion options, and a focus on efficiency and security, catering to the evolving needs of modern businesses.