SUPER MICRO Computer H8QM8-2, H8QME-2 I/O Port and Control Panel Connections, Front Control Panel

Page 27

Chapter 2: Installation

2-5 I/O Port and Control Panel Connections

The I/O ports are color coded in conformance with the PC99 specification to make setting up your system easier. See Figure 2-3 below for the colors and locations of the various I/O ports.

Figure 2-3. I/O Port Locations and Definitions

Front Control Panel

JF1 contains header pins for various front control panel connectors. See Figure 2-4 for the pin definitions of the various connectors. Refer to Section 2-6 for details.

Figure 2-4. JF1: Front Control Panel Header (JF1)

20 19

Ground x (key)

Power LED

HDD LED

NIC1

NIC2

OH/Fan Fail LED

Power Fail LED

Ground

Ground

2 1

NMI

x(key) Vcc Vcc Vcc Vcc Vcc Vcc

Reset Button Power Button

Note: NMI is not supported on the H8QM8-2 or the H8QME-2.

2-7

Image 27
Contents Super Manual Revision 1.0d Release Date September 9 Manual Organization About This ManualTable of Contents Table of Contents Troubleshooting BiosAppendices Overview ChecklistAsia-Pacific Contacting SupermicroHeadquarters EuropeH8QM8-2/H8QME-2 Image Super H8QM8-2 Jumpers Description Default Setting Connectors DescriptionH8QM8-2/H8QME-2 Quick Reference CPU Serverboard FeaturesOther NVidia MCP55 Pro/AMD-8132 Chipset HyperTransport Technology Chipset OverviewMCP55 Pro Media and Communications Processor AMD-8132 HyperTransport PCI-X TunnelCPU Overheat/Fan Fail LED and Control Auto-Switching Voltage Regulator for the CPU CorePC Health Monitoring Fan Status Monitor with Firmware/Software Speed ControlPower Configuration Settings Wake-On-Ring Header Jwor Power SupplySuper I/O H8QM8-2/H8QME-2 User’s Manual Unpacking PrecautionsInstallation Procedures Static-Sensitive DevicesCPU Backplates Processor and Heatsink InstallationPage Installing the Heatsink Installing the Heatsink Retention ModulesMounting the Serverboard into a Chassis Installing MemorySide and Top Views of DDR Installation Front Control Panel I/O Port and Control Panel ConnectionsNMI Button Connecting CablesATX Power Connector Processor Power ConnectorOverheat/Fan Fail LED Power LEDUniversal Serial Bus Ports USB0/1 Power Fail LEDReset Button Power ButtonChipset Fan Headers USB HeadersSerial Ports Fan HeadersOverheat LED Power LED/Keylock/SpeakerATX PS/2 Keyboard and PS/2 Mouse Ports Chassis IntrusionWake-On-Ring System Management Bus Power Header Pssmbus3rd Power Supply Alarm Reset Header Wake-On-LANCompact Flash Power Headers 3rd Power Supply Fail Detect HeaderJLAN1/2 Ethernet Ports Jumper Settings Explanation JumpersCmos Clear I2C to PCI-E Slots Enable/ Disable VGA Enable/DisableJlan Enable/Disable I2C to PCI-X Slots Enable/ DisableScsi Controller Enable/ Disable H8QM8-2 only Scsi Termination Enable/ Disable H8QM8-2 onlyCompact Flash Master/Slave PCI-X Slot Frequency Select Watch Dog Enable/DisableOnboard Indicators Onboard Power LED DP2JLAN1/JLAN2 LEDs Floppy, IDE, Parallel Port, Scsi and Sata Drive Connections Floppy ConnectorIDE Connector Sata Ports Parallel Port ConnectorDiffsens Termpwr Scsi Connectors H8QM8-2 onlySerial ATA Sata Installing the OS/SATA DriverEnabling Sata RAID in the Bios Enabling Sata RAIDInstalling the OS and Drivers Using the nVidia RAID UtilitySata RAID Utility Main Screen Driver Installation Display Screen Installing Software DriversPage No Video Troubleshooting ProceduresBefore Power On No PowerTechnical Support Procedures Memory ErrorsLosing the System’s Setup Configuration Question What type of memory does my serverboard support? Frequently Asked QuestionsReturning Merchandise for Service Introduction Starting the Setup UtilityAdvanced Settings Menu Boot FeaturesMain Menu Acpi Version Features Boot up Num-LockWait for ‘F1’ If Error OS InstallationCPU Configuration Floppy/IDE/SATA Configuration NVidia RAID SetupBlock Multi-Sector Transfer LBA/Large ModePrimary IDE Master/Slave TypeSerial ATA0/1/2 Primary/Secondary Channel DMA ModeA.R.T Bit Data TransferIDE Detect Time Out Sec Hard Disk Write ProtectPCI/PnP Configuration Super IO Configuration NorthBridge Configuration Chipset ConfigurationMem Clk Tristate C3/ALTVID CS Sparing EnableECC Configuration Dram ECC Enable Bit ECC ModeSouthBridge Configuration Event Log Configuration Remote Access ConfigurationSystem Fan Monitor System Health MonitorRemovable Drives Boot MenuBoot Device Priority Hard Disk DrivesSecurity Menu Change Supervisor PasswordChange User Password Boot Sector Virus ProtectionExit Menu Beep Code Error Message Description Amibios Error Beep CodesH8QM8-2/H8QME-2 User’s Manual Uncompressed Initialization Codes Appendix B Bios Post Checkpoint CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h