SUPER MICRO Computer H8QM8-2, H8QME-2 user manual SouthBridge Configuration

Page 65

Chapter 4: BIOS

Power Down Control

Allows DIMMs to enter power down mode by deasserting the clock enable signal when DIMMs are not in use. Options are Auto and Disabled.

Alternate VID

Specifies and alternate VID while in low power states. Options are Auto and various voltages between .8V and 1.115V.

Memory Timing Parameters

Allows the user to select which CPU Node's timing parameters (memory clock, etc.) to display. Options are CPU Node 0, CPU Node1, CPU Node2 and CPU Node3.

SouthBridge Configuration

USB 1.1 Controller

Enable or disable the USB 1.1 controller.

USB 2.0 Controller

Enable or disable the USB 2.0 controller.

USB Devices Enabled

This field dsiplays the USB devices currently enabled.

Legacy USB Support

Select "Enabled" to enable the support for USB Legacy. Disable Legacy support if there are no USB devices installed in the system. "Auto" disabled Legacy support if no USB devices are connected. The options are Disabled, Enabled and Auto.

USB 2.0 Controller Mode

Select the controller mode for your USB ports. Options are HiSpeed and FullSpeed. (HiSpeed=480 Mbps, FullSpeed=12 Mbps).

BIOS EHCI Hand-Off

Enable or Disable a workaround for OS's without EHCI hand-off support.

4-13

Image 65
Contents Super Manual Revision 1.0d Release Date September 9 Manual Organization About This ManualTable of Contents Table of Contents Appendices TroubleshootingBios Overview ChecklistHeadquarters Contacting SupermicroEurope Asia-PacificH8QM8-2/H8QME-2 Image Super H8QM8-2 H8QM8-2/H8QME-2 Quick Reference Jumpers Description Default SettingConnectors Description CPU Serverboard FeaturesOther NVidia MCP55 Pro/AMD-8132 Chipset MCP55 Pro Media and Communications Processor Chipset OverviewAMD-8132 HyperTransport PCI-X Tunnel HyperTransport TechnologyPC Health Monitoring Auto-Switching Voltage Regulator for the CPU CoreFan Status Monitor with Firmware/Software Speed Control CPU Overheat/Fan Fail LED and ControlPower Configuration Settings Wake-On-Ring Header Jwor Power SupplySuper I/O H8QM8-2/H8QME-2 User’s Manual Installation Procedures PrecautionsStatic-Sensitive Devices UnpackingCPU Backplates Processor and Heatsink InstallationPage Installing the Heatsink Installing the Heatsink Retention ModulesMounting the Serverboard into a Chassis Installing MemorySide and Top Views of DDR Installation Front Control Panel I/O Port and Control Panel ConnectionsATX Power Connector Connecting CablesProcessor Power Connector NMI ButtonOverheat/Fan Fail LED Power LEDReset Button Power Fail LEDPower Button Universal Serial Bus Ports USB0/1Serial Ports USB HeadersFan Headers Chipset Fan HeadersATX PS/2 Keyboard and PS/2 Mouse Ports Power LED/Keylock/SpeakerChassis Intrusion Overheat LED3rd Power Supply Alarm Reset Header System Management Bus Power Header PssmbusWake-On-LAN Wake-On-RingJLAN1/2 Ethernet Ports Compact Flash Power Headers3rd Power Supply Fail Detect Header Cmos Clear Jumper SettingsExplanation Jumpers Jlan Enable/Disable VGA Enable/DisableI2C to PCI-X Slots Enable/ Disable I2C to PCI-E Slots Enable/ DisableCompact Flash Master/Slave Scsi Controller Enable/ Disable H8QM8-2 onlyScsi Termination Enable/ Disable H8QM8-2 only PCI-X Slot Frequency Select Watch Dog Enable/DisableJLAN1/JLAN2 LEDs Onboard IndicatorsOnboard Power LED DP2 Floppy, IDE, Parallel Port, Scsi and Sata Drive Connections Floppy ConnectorIDE Connector Sata Ports Parallel Port ConnectorDiffsens Termpwr Scsi Connectors H8QM8-2 onlyEnabling Sata RAID in the Bios Installing the OS/SATA DriverEnabling Sata RAID Serial ATA SataInstalling the OS and Drivers Using the nVidia RAID UtilitySata RAID Utility Main Screen Driver Installation Display Screen Installing Software DriversPage Before Power On Troubleshooting ProceduresNo Power No VideoLosing the System’s Setup Configuration Technical Support ProceduresMemory Errors Question What type of memory does my serverboard support? Frequently Asked QuestionsReturning Merchandise for Service Introduction Starting the Setup UtilityMain Menu Advanced Settings MenuBoot Features Wait for ‘F1’ If Error Boot up Num-LockOS Installation Acpi Version FeaturesCPU Configuration Floppy/IDE/SATA Configuration NVidia RAID SetupPrimary IDE Master/Slave LBA/Large ModeType Block Multi-Sector TransferA.R.T DMA ModeBit Data Transfer Serial ATA0/1/2 Primary/Secondary ChannelIDE Detect Time Out Sec Hard Disk Write ProtectPCI/PnP Configuration Super IO Configuration NorthBridge Configuration Chipset ConfigurationECC Configuration Dram ECC Enable CS Sparing EnableBit ECC Mode Mem Clk Tristate C3/ALTVIDSouthBridge Configuration Event Log Configuration Remote Access ConfigurationSystem Fan Monitor System Health MonitorBoot Device Priority Boot MenuHard Disk Drives Removable DrivesChange User Password Change Supervisor PasswordBoot Sector Virus Protection Security MenuExit Menu Beep Code Error Message Description Amibios Error Beep CodesH8QM8-2/H8QME-2 User’s Manual Uncompressed Initialization Codes Appendix B Bios Post Checkpoint CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h