SUPER MICRO Computer H8QM8-2, H8QME-2 user manual IDE Connector

Page 41

Chapter 2: Installation

IDE Connector

IDE Drive Connector Pin Deﬁnitions (IDE#1)

There are no jumpers to con- ﬁgure the onboard IDE#1 con- nector. See the table on the right for pin deﬁnitions.

Pin# Deﬁnition

1 Reset IDE

3Host Data 7

5Host Data 6

7Host Data 5

9Host Data 4

11Host Data 3

13Host Data 2

15Host Data 1

17Host Data 0

19 Ground

21DRQ3

23I/O Write

25I/O Read

27IOCHRDY

29DACK3

31 IRQ14

33Addr1

35Addr0

37Chip Select 0

39Activity

Pin # Deﬁnition

2 Ground

4Host Data 8

6Host Data 9

8Host Data 10

10Host Data 11

12Host Data 12

14Host Data 13

16Host Data 14

18Host Data 15

20 Key

22Ground

24Ground

26Ground

28BALE

30Ground

32 IOCS16

34Ground

36Addr2

38Chip Select 1

40Ground

2-21

Image 41

Contents Super Manual Revision 1.0d Release Date September 9 Manual Organization About This ManualTable of Contents Table of Contents Appendices TroubleshootingBios Overview ChecklistHeadquarters Contacting SupermicroEurope Asia-PaciﬁcH8QM8-2/H8QME-2 Image Super H8QM8-2 H8QM8-2/H8QME-2 Quick Reference Jumpers Description Default SettingConnectors Description CPU Serverboard FeaturesOther NVidia MCP55 Pro/AMD-8132 Chipset MCP55 Pro Media and Communications Processor Chipset OverviewAMD-8132 HyperTransport PCI-X Tunnel HyperTransport TechnologyPC Health Monitoring Auto-Switching Voltage Regulator for the CPU CoreFan Status Monitor with Firmware/Software Speed Control CPU Overheat/Fan Fail LED and ControlPower Conﬁguration Settings Wake-On-Ring Header Jwor Power SupplySuper I/O H8QM8-2/H8QME-2 User’s Manual Installation Procedures PrecautionsStatic-Sensitive Devices UnpackingCPU Backplates Processor and Heatsink InstallationPage Installing the Heatsink Installing the Heatsink Retention ModulesMounting the Serverboard into a Chassis Installing MemorySide and Top Views of DDR Installation Front Control Panel I/O Port and Control Panel ConnectionsATX Power Connector Connecting CablesProcessor Power Connector NMI ButtonOverheat/Fan Fail LED Power LEDReset Button Power Fail LEDPower Button Universal Serial Bus Ports USB0/1Serial Ports USB HeadersFan Headers Chipset Fan HeadersATX PS/2 Keyboard and PS/2 Mouse Ports Power LED/Keylock/SpeakerChassis Intrusion Overheat LED3rd Power Supply Alarm Reset Header System Management Bus Power Header PssmbusWake-On-LAN Wake-On-RingJLAN1/2 Ethernet Ports Compact Flash Power Headers3rd Power Supply Fail Detect Header Cmos Clear Jumper SettingsExplanation Jumpers Jlan Enable/Disable VGA Enable/DisableI2C to PCI-X Slots Enable/ Disable I2C to PCI-E Slots Enable/ DisableCompact Flash Master/Slave Scsi Controller Enable/ Disable H8QM8-2 onlyScsi Termination Enable/ Disable H8QM8-2 only PCI-X Slot Frequency Select Watch Dog Enable/DisableJLAN1/JLAN2 LEDs Onboard IndicatorsOnboard Power LED DP2 Floppy, IDE, Parallel Port, Scsi and Sata Drive Connections Floppy ConnectorIDE Connector Sata Ports Parallel Port ConnectorDiffsens Termpwr Scsi Connectors H8QM8-2 onlyEnabling Sata RAID in the Bios Installing the OS/SATA DriverEnabling Sata RAID Serial ATA SataInstalling the OS and Drivers Using the nVidia RAID UtilitySata RAID Utility Main Screen Driver Installation Display Screen Installing Software DriversPage Before Power On Troubleshooting ProceduresNo Power No VideoLosing the System’s Setup Conﬁguration Technical Support ProceduresMemory Errors Question What type of memory does my serverboard support? Frequently Asked QuestionsReturning Merchandise for Service Introduction Starting the Setup UtilityMain Menu Advanced Settings MenuBoot Features Wait for ‘F1’ If Error Boot up Num-LockOS Installation Acpi Version FeaturesCPU Conﬁguration Floppy/IDE/SATA Conﬁguration NVidia RAID SetupPrimary IDE Master/Slave LBA/Large ModeType Block Multi-Sector TransferA.R.T DMA ModeBit Data Transfer Serial ATA0/1/2 Primary/Secondary ChannelIDE Detect Time Out Sec Hard Disk Write ProtectPCI/PnP Conﬁguration Super IO Conﬁguration NorthBridge Conﬁguration Chipset ConﬁgurationECC Conﬁguration Dram ECC Enable CS Sparing EnableBit ECC Mode Mem Clk Tristate C3/ALTVIDSouthBridge Conﬁguration Event Log Conﬁguration Remote Access ConﬁgurationSystem Fan Monitor System Health MonitorBoot Device Priority Boot MenuHard Disk Drives Removable DrivesChange User Password Change Supervisor PasswordBoot Sector Virus Protection Security MenuExit Menu Beep Code Error Message Description Amibios Error Beep CodesH8QM8-2/H8QME-2 User’s Manual Uncompressed Initialization Codes Appendix B Bios Post Checkpoint CodesBootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h