SMC Networks SMC8126L2 manual Safety Compliance

Page 7

Safety Compliance

Warning: Fiber Optic Port Safety

 

When using a fiber optic port, never look at the transmit laser while it is

CLASS I

powered on. Also, never look directly at the fiber TX port and fiber cable

LASER DEVICE

ends when they are powered on.

 

Avertissment: Ports pour fibres optiques - sécurité sur le plan optique

DISPOSITIF LASER

Ne regardez jamais le laser tant qu'il est sous tension. Ne regardez

jamais directement le port TX (Transmission) à fibres optiques et les

DE CLASSE I

embouts de câbles à fibres optiques tant qu'ils sont sous tension.

 

Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit

LASERGERÄT DER KLASSE I

Niemals ein Übertragungslaser betrachten, während dieses eingeschaltet ist. Niemals direkt auf den Faser-TX-Anschluß und auf die Faserkabelenden schauen, während diese eingeschaltet sind.

PSE Alarm

本製品に同梱いたしております電源コードセットは、 本製品専用です。本電源コードセットは、本製品以外の 製品並びに他の用途でご使用いただくことは出来ません。 製品本体に同梱された電源コードセットを利用し、他製品 の電源コードセットを使用しないで下さい。

Power Cord Safety

Please read the following safety information carefully before installing the switch:

WARNING: Installation and removal of the unit must be carried out by qualified personnel only.

The unit must be connected to an earthed (grounded) outlet to comply with international safety standards.

Do not connect the unit to an A.C. outlet (power supply) without an earth (ground) connection.

The appliance coupler (the connector to the unit and not the wall plug) must have a configuration for mating with an EN 60320/IEC 320 appliance inlet.

The socket outlet must be near to the unit and easily accessible. You can only remove power from the unit by disconnecting the power cord from the outlet.

This unit operates under SELV (Safety Extra Low Voltage) conditions according to IEC 60950. The conditions are only maintained if the equipment to which it is connected also operates under SELV conditions.

France and Peru only

This unit cannot be powered from ITsupplies. If your supplies are of IT type, this unit must be powered by 230 V (2P+T) via an isolation transformer ratio 1:1, with the secondary connection point labelled Neutral, connected directly to earth (ground).

Impédance à la terre

iii

Image 7
Contents Installation Guide Page TigerSwitch 10/100/1000 Installation Guide Page Compliances and Safety Warnings N11846 Safety Compliance Power Cord Set France et Pérou uniquement Sein und die Aufschrift HAR oder Basec tragen Manufacturing Materials End of Product Life SpanDocumentation Viii Contents Appendix B Cables Appendix a TroubleshootingAppendix C Specifications Making Network ConnectionsAppendix D Ordering Information Glossary Index Xii Tables Figures Overview IntroductionNetwork Management Options Switch ArchitecturePort and System Status LEDs Description of Hardware10/100/1000BASE-T Ports SFP SlotsLED Expandability Features and BenefitsPower Supply Socket ConnectivityManagement Network Planning Introduction to SwitchingCollapsed Backbone Application ExamplesNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Selecting a Site Installing the SwitchEthernet Cabling Package Contents Equipment ChecklistOptional Rack-Mounting Equipment Rack Mounting MountingDesktop or Shelf Mounting Installing the Switch in a RackInserting an SFP Transceiver into a Slot Installing an Optional SFP TransceiverConnecting to the Console Port Connecting to a Power SourceSerial Cable Wiring Switch’s 8-Pin Null Modem PC’s 9-Pin Wiring Map for Serial CableInstalling the Switch Cabling Guidelines Connecting Network DevicesMaking Network Connections Twisted-Pair DevicesNetwork Wiring Connections Connecting to PCs, Servers, Hubs and SwitchesFiber Optic SFP Devices Network Wiring ConnectionsMaking Connections to SFP Transceivers Connectivity RulesMbps Gigabit Ethernet Collision Domain 1000BASE-T Cable RequirementsMbps Fast Ethernet Collision Domain Mbps Ethernet Collision Domain Cable Labeling and Connection RecordsInstallation Appendix a TroubleshootingDiagnosing Switch Indicators Power and Cooling ProblemsIn-Band Access Twisted-Pair Cable and Pin Assignments Appendix B Cables10BASE-T/100BASE-TX Pin Assignments Crossover Wiring Straight-Through WiringTwisted-Pair Cable and Pin Assignments B 1000BASE-T Pin AssignmentsAdjusting Existing Category 5 Cabling to Run 1000BASE-T Cable Testing for Existing Category 5 CableFiber Standards Physical Characteristics Appendix C SpecificationsManagement Features Switch FeaturesStandards CE Mark CompliancesSpecifications Appendix D Ordering Information Ordering Information Glossary Full Duplex End StationEthernet Fast EthernetSwitched Ports Media Access Control MACRedundant Power Supply RPS RJ-45 ConnectorVirtual LAN Vlan Transmission Control Protocol/Internet Protocol TCP/IPNumerics IndexIndex Page Technical Support

SMC8126L2 specifications

The SMC8126L2 is a robust Layer 2 managed switch developed by SMC Networks, designed to meet the demands of modern networking environments. This switch is part of the SMC's lineup of network solutions, emphasizing reliability, efficiency, and advanced functionalities suitable for both small and medium-sized enterprises.

One of the standout features of the SMC8126L2 is its support for 26 ports, which allow multiple devices to connect seamlessly. This includes 24 Fast Ethernet ports (10/100 Mbps) and 2 gigabit uplink ports. This configuration enables flexible network designs and enhances the bandwidth availability for devices that require faster data transmission.

The SMC8126L2 is equipped with various Layer 2 switching capabilities, including port-based Virtual LAN (VLAN) support, allowing businesses to segment their networks for better security and performance. This capability ensures that sensitive data remains isolated and reduces broadcast traffic across the entire network. The switch also supports 802.1Q tagging for VLAN configuration, facilitating the management of multiple VLANs simultaneously.

Quality of Service (QoS) is another significant aspect of the SMC8126L2. It employs intelligent traffic management features, prioritizing critical applications such as VoIP and video conferencing. This ensures that time-sensitive data packets are transmitted efficiently, minimizing latency and improving overall user experience. The switch supports multiple QoS mechanisms, such as 802.1p priority tagging and port-based scheduling, thus accommodating varied networking needs.

Security features are paramount in the SMC8126L2, with network access control through Port Security and MAC address filtering. This prevents unauthorized access and enhances the security posture of the network. Additionally, the switch supports IGMP Snooping, which conserves bandwidth by ensuring that multicast traffic is only sent to ports that require it.

Another remarkable aspect of the SMC8126L2 is its management capabilities. The switch can be managed through various methods, including web-based interfaces, command-line interfaces (CLI), and SNMP (Simple Network Management Protocol). This flexibility allows network administrators to monitor performance, configure settings, and troubleshoot issues effectively.

In summary, the SMC8126L2 brings a suite of advanced features and technologies that cater to the evolving requirements of networking. With its extensive port options, VLAN support, QoS capabilities, robust security measures, and versatile management interfaces, the SMC8126L2 stands out as a reliable choice for organizations looking to enhance their networking infrastructure. Its performance and reliability make it well-suited for addressing the challenges of modern network environments while ensuring efficient data flow and security.