SMC Networks SMC8126L2 manual Installing an Optional SFP Transceiver

Page 35

Installing an Optional SFP Transceiver 3

3.If installing a single switch only, go to “Connecting to a Power Source” at the end of this chapter.

4.If installing multiple switches, attach four adhesive feet to each one. Place each device squarely on top of the one below, in any order.

Installing an Optional SFP Transceiver

Figure 3-5 Inserting an SFP Transceiver into a Slot

The switch supports 1000BASE-SX and 1000BASE-LX, and 1000BASE-ZX SFP-compatible transceivers. To install an SFP transceiver, do the following:

1.Consider network and cabling requirements to select an appropriate SFP transceiver type.

2.Insert the transceiver with the optical connector facing outward and the slot connector facing down. Note that SFP transceivers are keyed so they can only be installed in one orientation.

3.Slide the SFP transceiver into the slot until it clicks into place.

Note: SFP transceivers are hot-swappable. The switch does not need to be powered off before installing or removing a transceiver. However, always first disconnect the network cable before removing a transceiver.

Note: SFP transceivers are not provided in the switch package.

3-5

Image 35

Contents Installation Guide Page TigerSwitch 10/100/1000 Installation Guide Page Compliances and Safety Warnings N11846 Safety Compliance Power Cord Set France et Pérou uniquement Sein und die Aufschrift HAR oder Basec tragen Documentation End of Product Life SpanManufacturing Materials Viii Contents Appendix B Cables Appendix a TroubleshootingAppendix C Specifications Making Network ConnectionsAppendix D Ordering Information Glossary Index Xii Tables Figures Overview IntroductionNetwork Management Options Switch ArchitecturePort and System Status LEDs Description of Hardware10/100/1000BASE-T Ports SFP SlotsLED Expandability Features and BenefitsPower Supply Socket ConnectivityManagement Network Planning Introduction to SwitchingCollapsed Backbone Application ExamplesNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Ethernet Cabling Installing the SwitchSelecting a Site Optional Rack-Mounting Equipment Equipment Checklist Package Contents Rack Mounting MountingDesktop or Shelf Mounting Installing the Switch in a RackInserting an SFP Transceiver into a Slot Installing an Optional SFP TransceiverConnecting to the Console Port Connecting to a Power SourceSerial Cable Wiring Switch’s 8-Pin Null Modem PC’s 9-Pin Wiring Map for Serial CableInstalling the Switch Cabling Guidelines Connecting Network DevicesMaking Network Connections Twisted-Pair DevicesNetwork Wiring Connections Connecting to PCs, Servers, Hubs and SwitchesFiber Optic SFP Devices Network Wiring ConnectionsMaking Connections to SFP Transceivers Connectivity RulesMbps Fast Ethernet Collision Domain 1000BASE-T Cable RequirementsMbps Gigabit Ethernet Collision Domain Mbps Ethernet Collision Domain Cable Labeling and Connection RecordsInstallation Appendix a TroubleshootingDiagnosing Switch Indicators Power and Cooling ProblemsIn-Band Access 10BASE-T/100BASE-TX Pin Assignments Appendix B CablesTwisted-Pair Cable and Pin Assignments Crossover Wiring Straight-Through WiringTwisted-Pair Cable and Pin Assignments B 1000BASE-T Pin AssignmentsFiber Standards Cable Testing for Existing Category 5 CableAdjusting Existing Category 5 Cabling to Run 1000BASE-T Physical Characteristics Appendix C SpecificationsStandards Switch FeaturesManagement Features CE Mark CompliancesSpecifications Appendix D Ordering Information Ordering Information Glossary Full Duplex End StationEthernet Fast EthernetSwitched Ports Media Access Control MACRedundant Power Supply RPS RJ-45 ConnectorVirtual LAN Vlan Transmission Control Protocol/Internet Protocol TCP/IPNumerics IndexIndex Page Technical Support