SMC Networks SMC8126L2 manual Connecting to a Power Source, Connecting to the Console Port

Page 36

3 Installing the Switch

Connecting to a Power Source

To connect a device to a power source:

1.Insert the power cable plug directly into the socket located at the back of the device.

100-240V~50-60Hz 1.5A

Figure 3-6 Power Socket

2.Plug the other end of the cable into a grounded, 3-pin, AC power source.

Note: For international use, you may need to change the AC line cord. You must use a line cord set that has been approved for the receptacle type in your country.

3.Check the front-panel LEDs as the device is powered on to be sure the Power LED is on. If not, check that the power cable is correctly plugged in.

Connecting to the Console Port

The RJ-45 serial port on the switch’s front panel is used to connect to the switch for out-of-band console configuration. The on-board configuration program can be accessed from a terminal or a PC running a terminal emulation program. The pin assignments used to connect to the serial port are provided in the following table.

8

8

11

Figure 3-7 Serial Port (RJ-45) Pin-Out

3-6

Image 36

Contents Installation Guide Page TigerSwitch 10/100/1000 Installation Guide Page Compliances and Safety Warnings N11846 Safety Compliance Power Cord Set France et Pérou uniquement Sein und die Aufschrift HAR oder Basec tragen End of Product Life Span Manufacturing MaterialsDocumentation Viii Contents Appendix a Troubleshooting Appendix C SpecificationsMaking Network Connections Appendix B CablesAppendix D Ordering Information Glossary Index Xii Tables Figures Introduction OverviewSwitch Architecture Network Management OptionsDescription of Hardware 10/100/1000BASE-T PortsSFP Slots Port and System Status LEDsLED Features and Benefits Power Supply SocketConnectivity ExpandabilityManagement Introduction to Switching Network PlanningApplication Examples Collapsed BackboneNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Installing the Switch Selecting a SiteEthernet Cabling Equipment Checklist Package ContentsOptional Rack-Mounting Equipment Mounting Rack MountingInstalling the Switch in a Rack Desktop or Shelf MountingInstalling an Optional SFP Transceiver Inserting an SFP Transceiver into a SlotConnecting to a Power Source Connecting to the Console PortWiring Map for Serial Cable Serial Cable Wiring Switch’s 8-Pin Null Modem PC’s 9-PinInstalling the Switch Connecting Network Devices Making Network ConnectionsTwisted-Pair Devices Cabling GuidelinesConnecting to PCs, Servers, Hubs and Switches Network Wiring ConnectionsNetwork Wiring Connections Fiber Optic SFP DevicesConnectivity Rules Making Connections to SFP Transceivers1000BASE-T Cable Requirements Mbps Gigabit Ethernet Collision DomainMbps Fast Ethernet Collision Domain Cable Labeling and Connection Records Mbps Ethernet Collision DomainAppendix a Troubleshooting Diagnosing Switch IndicatorsPower and Cooling Problems InstallationIn-Band Access Appendix B Cables Twisted-Pair Cable and Pin Assignments10BASE-T/100BASE-TX Pin Assignments Straight-Through Wiring Crossover Wiring1000BASE-T Pin Assignments Twisted-Pair Cable and Pin Assignments BCable Testing for Existing Category 5 Cable Adjusting Existing Category 5 Cabling to Run 1000BASE-TFiber Standards Appendix C Specifications Physical CharacteristicsSwitch Features Management FeaturesStandards Compliances CE MarkSpecifications Appendix D Ordering Information Ordering Information Glossary End Station EthernetFast Ethernet Full DuplexMedia Access Control MAC Redundant Power Supply RPSRJ-45 Connector Switched PortsTransmission Control Protocol/Internet Protocol TCP/IP Virtual LAN VlanIndex NumericsIndex Page Technical Support