SMC Networks SMC8126L2 Appendix a Troubleshooting, Diagnosing Switch Indicators, Installation

Page 45

Appendix A: Troubleshooting

Diagnosing Switch Indicators

 

Table A-1 Troubleshooting Chart

Symptom

Action

 

 

Power LED is Off

• Check connections between the switch, the power cord, and the wall

 

outlet.

 

• Contact your dealer for assistance.

 

 

Power LED is Amber

• Internal power supply has failed. Contact your local dealer for

 

assistance.

 

 

Diag LED is Amber

• Power cycle the switch to try and clear the condition.

 

• If the condition does not clear, contact your local dealer for assistance.

 

 

Link LED is Off

• Verify that the switch and attached device are powered on.

 

• Be sure the cable is plugged into both the switch and corresponding

 

device.

 

• Verify that the proper cable type is used and its length does not exceed

 

specified limits.

 

• Check the adapter on the attached device and cable connections for

 

possible defects. Replace the defective adapter or cable if necessary.

 

 

Power and Cooling Problems

If the power indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet, power cord, or internal power supply. However, if the unit powers off after running for a while, check for loose power connections, power losses or surges at the power outlet, and verify that the fans on the unit are unobstructed and running prior to shutdown. If you still cannot isolate the problem, then the internal power supply may be defective.

Installation

Verify that all system components have been properly installed. If one or more components appear to be malfunctioning (such as the power cord or network cabling), test them in an alternate environment where you are sure that all the other components are functioning properly.

A-1

Image 45
Contents Installation Guide Page TigerSwitch 10/100/1000 Installation Guide Page Compliances and Safety Warnings N11846 Safety Compliance Power Cord Set France et Pérou uniquement Sein und die Aufschrift HAR oder Basec tragen End of Product Life Span Manufacturing MaterialsDocumentation Viii Contents Appendix C Specifications Appendix a TroubleshootingMaking Network Connections Appendix B CablesAppendix D Ordering Information Glossary Index Xii Tables Figures Overview IntroductionNetwork Management Options Switch Architecture10/100/1000BASE-T Ports Description of HardwareSFP Slots Port and System Status LEDsLED Power Supply Socket Features and BenefitsConnectivity ExpandabilityManagement Network Planning Introduction to SwitchingCollapsed Backbone Application ExamplesNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsApplication Notes Installing the Switch Selecting a SiteEthernet Cabling Equipment Checklist Package ContentsOptional Rack-Mounting Equipment Rack Mounting MountingDesktop or Shelf Mounting Installing the Switch in a RackInserting an SFP Transceiver into a Slot Installing an Optional SFP TransceiverConnecting to the Console Port Connecting to a Power SourceSerial Cable Wiring Switch’s 8-Pin Null Modem PC’s 9-Pin Wiring Map for Serial CableInstalling the Switch Making Network Connections Connecting Network DevicesTwisted-Pair Devices Cabling GuidelinesNetwork Wiring Connections Connecting to PCs, Servers, Hubs and SwitchesFiber Optic SFP Devices Network Wiring ConnectionsMaking Connections to SFP Transceivers Connectivity Rules1000BASE-T Cable Requirements Mbps Gigabit Ethernet Collision DomainMbps Fast Ethernet Collision Domain Mbps Ethernet Collision Domain Cable Labeling and Connection RecordsDiagnosing Switch Indicators Appendix a TroubleshootingPower and Cooling Problems InstallationIn-Band Access Appendix B Cables Twisted-Pair Cable and Pin Assignments10BASE-T/100BASE-TX Pin Assignments Crossover Wiring Straight-Through WiringTwisted-Pair Cable and Pin Assignments B 1000BASE-T Pin AssignmentsCable Testing for Existing Category 5 Cable Adjusting Existing Category 5 Cabling to Run 1000BASE-TFiber Standards Physical Characteristics Appendix C SpecificationsSwitch Features Management FeaturesStandards CE Mark CompliancesSpecifications Appendix D Ordering Information Ordering Information Glossary Ethernet End StationFast Ethernet Full DuplexRedundant Power Supply RPS Media Access Control MACRJ-45 Connector Switched PortsVirtual LAN Vlan Transmission Control Protocol/Internet Protocol TCP/IPNumerics IndexIndex Page Technical Support

SMC8126L2 specifications

The SMC8126L2 is a robust Layer 2 managed switch developed by SMC Networks, designed to meet the demands of modern networking environments. This switch is part of the SMC's lineup of network solutions, emphasizing reliability, efficiency, and advanced functionalities suitable for both small and medium-sized enterprises.

One of the standout features of the SMC8126L2 is its support for 26 ports, which allow multiple devices to connect seamlessly. This includes 24 Fast Ethernet ports (10/100 Mbps) and 2 gigabit uplink ports. This configuration enables flexible network designs and enhances the bandwidth availability for devices that require faster data transmission.

The SMC8126L2 is equipped with various Layer 2 switching capabilities, including port-based Virtual LAN (VLAN) support, allowing businesses to segment their networks for better security and performance. This capability ensures that sensitive data remains isolated and reduces broadcast traffic across the entire network. The switch also supports 802.1Q tagging for VLAN configuration, facilitating the management of multiple VLANs simultaneously.

Quality of Service (QoS) is another significant aspect of the SMC8126L2. It employs intelligent traffic management features, prioritizing critical applications such as VoIP and video conferencing. This ensures that time-sensitive data packets are transmitted efficiently, minimizing latency and improving overall user experience. The switch supports multiple QoS mechanisms, such as 802.1p priority tagging and port-based scheduling, thus accommodating varied networking needs.

Security features are paramount in the SMC8126L2, with network access control through Port Security and MAC address filtering. This prevents unauthorized access and enhances the security posture of the network. Additionally, the switch supports IGMP Snooping, which conserves bandwidth by ensuring that multicast traffic is only sent to ports that require it.

Another remarkable aspect of the SMC8126L2 is its management capabilities. The switch can be managed through various methods, including web-based interfaces, command-line interfaces (CLI), and SNMP (Simple Network Management Protocol). This flexibility allows network administrators to monitor performance, configure settings, and troubleshoot issues effectively.

In summary, the SMC8126L2 brings a suite of advanced features and technologies that cater to the evolving requirements of networking. With its extensive port options, VLAN support, QoS capabilities, robust security measures, and versatile management interfaces, the SMC8126L2 stands out as a reliable choice for organizations looking to enhance their networking infrastructure. Its performance and reliability make it well-suited for addressing the challenges of modern network environments while ensuring efficient data flow and security.