SMC Networks SMCWHSG44-G manual

Page 29

of the Ethernet WAN interface has to be manually set, select Router with a Static-IP DSL/Cable Connection.

•If you have multiple ADSL/cable connections, select Router with n DSL/Cable Connections. Select the number of connections using the drop-down list, and then specify the type, downlink date rate and uplink data rate of each ADSL/cable connection. The specified data rates affect the load-balancing engine of the SMCWHSG44-G.

1.8.3.SETUP WIZARD Step 2: Configuring TCP/IP Settings

1.8.3.1.Router with a PPPoE-Based DSL/Cable Connection

Fig. 12. TCP/IP Settings for Router with a PPPoE-Based

DSL/Cable Connection mode.

If the SMCWHSG44-Gis set to be in Router with a PPPoE-Based DSL/Cable Connection mode, two IP addresses are needed-one for the Ethernet LAN interface and the other for the WAN interface. The LAN IP address must be set manually to a private IP address, say 192.168.2.xxx. The default LAN IP address is 192.168.2.1 and the default subnet mask is 255.255.255.0. In most cases, these default settings need no change.

As for the WAN IP address, it is obtained automatically by PPPoE from the ISP. Consult your ISP for the correct User name, Password, and Service name settings.

The Trigger mode setting specifies the way a PPPoE connection is established. Your PPPoE connection can be established and disconnected manually (Manual) by clicking the Connect and Disconnect buttons on the Start page, respectively. Or you can choose to let the device automatically (Auto) establish a PPPoE connection at boot-up time. In Auto mode, if the connection is disrupted, the device will omtry to reestablish the broken connection automatically.

28

Image 29

Contents SMCWHSG44-G Page Trademarks CopyrightLimited Warranty Page Industry Canada Class B Federal Communication Commission Interference StatementFCC Radiation Exposure Statement EC Conformance Declaration Power Cord Safety Safety ComplianceSchuko Page Wichtige Sicherheitshinweise Germany Schuko Page Table of Contents System Page SMCWHSG44-G SMCWHS-POS Introduction Ieee 802.11b/g Compliant Wireless Operation Overview FeaturesUser Authentication, Authorization, and Accounting AAA Internet Connection Sharing Network Security Firmware Tools Rear Panel Package ChecklistLED Definition POE enabled LAN Port Position Selecting a Power Supply MethodMounting the SMCWHSG44-G on a Wall Changing the TCP/IP Settings of the Managing Computer Preparing for ConfigurationEntering the Password Configuring the SMCWHSG44-GHome Setup Wizard Selecting an Operational ModePage Router with a Static-IP DSL/Cable Connection Router with a DHCP-Based DSL/Cable ConnectionRouter with Multiple DSL/Cable Connections Setup Wizard Configuring Ieee 802.11 Settings Setup Wizard Configuring Dhcp Server SettingsWeb Redirection Configuring User Authentication SettingsAuthentication protocol Local Authentication SeverPage Account Table List How to Setup the Mini-POS Ticket PrinterIeee Radius Settings Allowable Authentication Modes Configuring Radius SettingsDeploying the SMCWHSG44-G Setting up Client ComputersConfiguring TCP/IP-Related Settings Configuring Ieee 802.11-Related SettingsTo establish a wireless link to an AP Page Authentication Success Logout OverviewMenu Structure Page Status Associated Wireless Clients Save, Save & Restart, and Cancel CommandsHome and Refresh Commands Account Table Authenticated UsersManaged LAN Devices Session ListSystem Specifying Operational ModeManaging Firmware Changing PasswordUpgrading Firmware by Http Backing up and Restoring Configuration Settings by HttpTo upgrade firmware of the SMCWHSG44-G by Http Upgrading Firmware by Tftp To upgrade firmware of the SMCWHSG44-G by TftpTo back up configuration of the SMCWHSG44-G by Tftp Backing up and Restoring Configuration Settings by TftpTo restore configuration of the SMCWHSG44-G by Tftp Time Zone Resetting Configuration to Factory DefaultsConfiguring TCP/IP Related Settings Address Router with a DHCP-Based DSL/Cable Connection Router with a Static-IP DSL/Cable Connection DNS DNS Proxy NAT Basic Host Address ResolutionDhcp Server To expose preset internal serversVirtual Server Mappings Ii. Static Dhcp Mappings Dhcp Server BasicTo always assign an IP address to a specific Dhcp client Dhcp RelayLoad Balancing Configuring Ieee 802.11-Related Settings Wireless Basic Zero Client ReconfigurationWireless Distribution System To enable a WDS link Wireless Distribution System SettingsNetwork Topology Containing a Loop SecurityPage MAC-Address-Based Access Control Settings MAC-Address-Based Access ControlIeee 802.1x/RADIUS To deny wireless clients access to the wireless networkTo grant wireless clients access to the wireless network Ieee 802.1x/RADIUS Settings Configuring Authentication Settings AAA Basic Default Authentication Failure Warning To specify an uncontrolled computer by MAC address Unrestricted ClientsRadius Basic Walled GardenRobustness Log-On Page Customization Settings Authentication Session ControlAuthentication Success Page Customization Settings Ddns Advertisement Links SettingsIcmp TCP UDP To set a rule for packet filtering VlanFirewall To block Http traffic to an unwelcome Web site URL FiltersManagement Basic System Log UPnPSnmp Access RulesLAN Device Management Unrestricted Host MAC Address SettingsTo specify a LAN device to manage Example for LAN Device ManagementAppendix a Default SettingsLED Definitions TCP/IP Setting Problems Page Other Problems Wireless Settings ProblemsAppendix C Distances and Data Rates Transmission output Power Network ConfigurationConfiguration and Management StandardsKeypad Authentication Access PointBasic Service Set BSS Ad HocExtended Service Set ESS Dynamic Host Configuration Protocol DhcpExtensible Authentication Protocol EAP EncryptionPower over Ethernet PoE Inter Access Point Protocol IappInfrastructure Local Area Network LANWireless Distribution System WDS Service Set Identifier SsidWi-Fi Protected Access Session KeyWPA Pre-shared Key PSK Wired Equivalent Privacy WEPPage For Technical SUPPORT, Call