Seagate ST31000533CS manual Environmental specifications

Page 16

2.8Environmental specifications

2.8.1Ambient temperature

Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 69°C (156°F) within the operating ambient conditions.

Above 1,000 feet (305 meters), the maximum temperature is derated linearly to 112°F (44°C) at 10,000 feet (3,048 meters).

Operating:

0° to 60°C (32° to 140°F)

 

 

Nonoperating:

–40° to 70°C (–40° to 158°F)

 

 

2.8.2Temperature gradient

Operating:

20°C per hour (68°F per hour max), without condensation

 

 

Nonoperating:

30°C per hour (86°F per hour max)

 

 

2.8.3Humidity

2.8.3.1Relative humidity

Operating:

5% to 95% noncondensing (30% per hour max)

 

 

Nonoperating:

5% to 95% noncondensing (30% per hour max)

 

 

2.8.3.2Wet bulb temperature

Operating:

37.7°C (99.9°F max)

 

 

Nonoperating:

40°C (104°F max)

 

 

2.8.4Altitude

Operating:

–60.96 m to 3,048 m (–200 ft. to 10,000+ ft.)

 

 

Nonoperating:

–60.96 m to 12,192 m (–200 ft. to 40,000+ ft.)

 

 

2.8.5Shock

All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis.

2.8.5.1Operating shock

These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 70 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second.

10

Pipeline HD Pro Serial ATA Product Manual, Rev. C

Image 16
Contents Pipeline HD Pro Serial ATA ST31000533CSRevision history Revision Date Sheets affected or commentsContents Pipeline HD Pro Serial ATA Product Manual, Rev. C List of Figures Page Introduction About the Serial ATA interface Drive specifications Drive specifications summary for 1000 Gbyte models Will display the warranty information for your drive Default logical geometry LBA modeFormatted capacity Recording and interface technologyPhysical characteristics Seek timeStart/stop times Typical seek times msec Read WritePower specifications Power-management modes Active modeIdle mode Sleep modeEnvironmental specifications Nonoperating shock GB models VibrationOperating vibration Nonoperating vibrationAcoustics Electromagnetic immunityFluid Dynamic Bearing FDB motor acoustics Test for Prominent Discrete Tones PDTsSafety certification ReliabilityAgency certification Electromagnetic compatibilityAustralian C-Tick N176 Korean RRLFCC verification Environmental protection Corrosive environmentPipeline HD Pro Serial ATA Product Manual, Rev. C Configuring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsMounting dimensions 1000 GB models Drive mountingPipeline HD Pro Serial ATA Product Manual, Rev. C Serial ATA Sata interface Hot-Plug compatibilitySerial ATA device plug connector pin definitions Serial ATA connector pin definitionsSignal Pin Function DefinitionSupported ATA commands Supported ATA commandsCommand name Command code in hex F4H Identify Device command Word Description ValueXx07H Description if bit is set to Bit Word Bit WordWord Set Features command Set Features command valuesA.R.T. commands 3 S.M.A.R.T. commandsCode in features register A.R.T. command Presales Support Seagate Technology support servicesTechnical Support Data Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Index ITE Page Pipeline HD Pro Serial ATA Product Manual, Rev. C Page Disc Drive, Scotts Valley, California 95066-4544, USA