Seagate ST31000533CS manual Ite

Page 40

I/O duty cycle				13
Identify Device				23
Identify Device command 25
Idle	9,	23
Idle Immediate				23
Idle mode 8,				9
IEC950		13
Information Technology Equipment (ITE) 13
Initialize Device Parameters					23
Input noise ripple 8
input voltage			8
interface		6,	21
interference			14
internal data-transfer rate OD					6
is 7
ISO document 7779 12
ITE	13

K

Korea Ministry of Information and Communication

(MIC) 14

Korean RRL 14

L

latency 7 LBA mode 6 length 7

logical geometry 6

M

maintenance 13 master/slave 2 maximum temperature 10

Mean Time Between Failures 13 MIC 14

mounting 19 mounting screws 10 mounting the drive 17 MTBF 13

N

noise 8

nominal power 7 Nonoperating shock 11 Nonoperating vibration 11 Nonrecoverable read errors 13

O

operating 8 Operating power 8 Operating shock 10 Operating vibration 11

P

Physical characteristics 7 point-to-point 2, 18 Power consumption 8 power dissipation 8 Power modes 9

Power specifications 8 Power-management modes 9 Power-on to Ready 7 power-on-hours 13 precautions 17

printed circuit board 17 programmable power management 9 prominent discrete tone 12

Q

quick reference 3

R

Radiated RF immunity					12
radio and television interference 14
radio frequency (RF)					12
Read Buffer		23
Read DMA		23
Read DMA Extended					23
Read DMA without Retries 23
read errors		13
Read Log Ext			23
Read Multiple			23
Read Multiple Extended 23
Read Native Max Address 23
Read Native Max Address Extended							23
Read Sectors			23
Read Sectors Extended 23
Read Sectors Without Retries						23
Read Verify Sectors 23
Read Verify Sectors Extended						23
Read Verify Sectors Without Retries							23
Read/write heads				6
Recalibrate		23
recording density				6
recording method				6
Recording technology					6
relative humidity				10
Reliability 13
RF 12
RMS read/write current 8
RoHS	15
RRL	14

S

S.M.A.R.T. Disable Operations 24 S.M.A.R.T. Enable Operations 24

34	Pipeline HD Pro Serial ATA Product Manual, Rev. C

Image 40

Contents Pipeline HD Pro Serial ATA ST31000533CSRevision history Revision Date Sheets affected or commentsContents Pipeline HD Pro Serial ATA Product Manual, Rev. C List of Figures Page Introduction About the Serial ATA interface Drive specifications Drive specifications summary for 1000 Gbyte models Will display the warranty information for your drive Default logical geometry LBA modeFormatted capacity Recording and interface technologyPhysical characteristics Seek timeStart/stop times Typical seek times msec Read WritePower specifications Power-management modes Active modeIdle mode Sleep modeEnvironmental specifications Nonoperating shock GB models VibrationOperating vibration Nonoperating vibrationAcoustics Electromagnetic immunityFluid Dynamic Bearing FDB motor acoustics Test for Prominent Discrete Tones PDTsSafety certification ReliabilityAgency certification Electromagnetic compatibilityAustralian C-Tick N176 Korean RRLFCC verification Environmental protection Corrosive environmentPipeline HD Pro Serial ATA Product Manual, Rev. C Configuring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsMounting dimensions 1000 GB models Drive mountingPipeline HD Pro Serial ATA Product Manual, Rev. C Serial ATA Sata interface Hot-Plug compatibilitySerial ATA device plug connector pin definitions Serial ATA connector pin definitionsSignal Pin Function DefinitionSupported ATA commands Supported ATA commandsCommand name Command code in hex F4H Identify Device command Word Description ValueXx07H Description if bit is set to Bit Word Bit WordWord Set Features command Set Features command valuesA.R.T. commands 3 S.M.A.R.T. commandsCode in features register A.R.T. command Presales Support Seagate Technology support servicesTechnical Support Data Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Index ITE Page Pipeline HD Pro Serial ATA Product Manual, Rev. C Page Disc Drive, Scotts Valley, California 95066-4544, USA