Seagate ST31000533CS manual Drive mounting, Mounting dimensions 1000 GB models

Page 25

3.4Drive mounting

You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 3 for drive mounting dimensions. Follow these important mounting precau- tions when mounting the drive:

Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.

Use only 6-32 UNC mounting screws.

The screws should be inserted no more than 0.150 inch (3.81 mm) into the bottom or side mounting holes.

Do not overtighten the mounting screws (maximum torque: 6 inch-lb).

[1]

5.787 (146.9898) max.

Recommended case temperature measurement location

 

 

1.122

 

 

 

 

 

1.638

 

 

 

 

 

 

 

(41.605)

[1]

 

 

+ .020

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(28.499

 

 

 

 

 

 

 

 

 

 

 

 

 

+.508)

[1][1]

4.000

(101.6)

.250 + .015 (6.35 + .381) (3x both sides)

4.000

(101.60)

.138

(3.505)

.814

(20.676)

C of conn. Datum B

L

2.00

(50.80)

C of drive

L

[1]

2 x 3.750

(2 x 95.25)

1.028 max [1]

(26.111 max)

Notes:

Dimensions are shown in inches (mm).

[1] Dimensions per SFF-8301 specification

2 x 1.625

(2 x 41.28) [1]

2 x 1.750 [1] (2 x 44.45)

4.000

(101.6)

[1]

Recommended case temperature measurement location

Figure 3. Mounting dimensions (1000 GB models)

Pipeline HD Pro Serial ATA Product Manual, Rev. C

19

Image 25
Contents ST31000533CS Pipeline HD Pro Serial ATARevision Date Sheets affected or comments Revision historyContents Pipeline HD Pro Serial ATA Product Manual, Rev. C List of Figures Page Introduction About the Serial ATA interface Drive specifications Drive specifications summary for 1000 Gbyte models Will display the warranty information for your drive LBA mode Default logical geometryFormatted capacity Recording and interface technologySeek time Physical characteristicsStart/stop times Typical seek times msec Read WritePower specifications Active mode Power-management modesIdle mode Sleep modeEnvironmental specifications Vibration Nonoperating shock GB modelsOperating vibration Nonoperating vibrationElectromagnetic immunity AcousticsFluid Dynamic Bearing FDB motor acoustics Test for Prominent Discrete Tones PDTsReliability Safety certificationAgency certification Electromagnetic compatibilityAustralian C-Tick N176 Korean RRLFCC verification Corrosive environment Environmental protectionPipeline HD Pro Serial ATA Product Manual, Rev. C Handling and static-discharge precautions Configuring and mounting the driveSerial ATA cables and connectors Configuring the driveDrive mounting Mounting dimensions 1000 GB modelsPipeline HD Pro Serial ATA Product Manual, Rev. C Hot-Plug compatibility Serial ATA Sata interfaceSerial ATA connector pin definitions Serial ATA device plug connector pin definitionsSignal Pin Function DefinitionSupported ATA commands Supported ATA commandsCommand name Command code in hex F4H Word Description Value Identify Device commandXx07H Bit Word Description if bit is set to Bit WordWord Set Features command values Set Features commandA.R.T. commands 3 S.M.A.R.T. commandsCode in features register A.R.T. command Presales Support Seagate Technology support servicesTechnical Support Data Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Index ITE Page Pipeline HD Pro Serial ATA Product Manual, Rev. C Page Disc Drive, Scotts Valley, California 95066-4544, USA