Seagate ST3160316CS Configuring and mounting the drive, Handling and static-discharge precautions

Page 29

3.0Configuring and mounting the drive

3.0Configuring and mounting the drive

This section contains the specifications and instructions for configuring and mounting the drive.

3.1Handling and static-discharge precautions

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis- charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:

Caution:

•Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure.

•Handle the drive by its edges or frame only.

•The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.

•Always rest the drive on a padded, antistatic surface until you mount it in the computer.

•Do not touch the connector pins or the printed circuit board.

•Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination.

Pipeline HD.2 Series SATA Product Manual, Rev. E

21

Image 29

Contents ST3320413CSST3320310CS ST3250412CSST3250312CS ST3160316CS ST31000424CSST31000322CS ST3500414CSST3500312CSPipeline HD.2 Series SATA Product ManualRevision Revision historyDate Sheets affected or commentsPipeline HD.2 Series SATA Product Manual, Rev. E Pipeline HD.2 Series SATA Product Manual, Rev. E 2.0 Drive specifications Contents3.0 Configuring and mounting the drive 5.0 Seagate Technology support servicesPipeline HD.2 Series SATA Product Manual, Rev. E List of Figures Page 1.0 Introduction 1.1 About the Serial ATA interface 2.1 Specification summary tables 2.0 Drive specificationsDrive specification Drive specifications summary for 1000GB modelsST31000424CS ST31000322CSOperational Shock max page support.seagate.com/customer/warrantyvalidation.jspST3500414CS Drive specifications summary for 500 and 320GB modelsST3500312CS ST3320413CSpage support.seagate.com/customer/warrantyvalidation.jsp ST3250412CS Drive specifications summary for 250 and 160GB modelsST3250312CS ST3160316CSST3250412CS 2.2 Formatted capacity 2.3 Default logical geometry2.4 Recording and interface technology 2.2.1 LBA mode2.6 Seek time Physical characteristics2.7 Start/stop times 101.85mm / 4.010 in2.8.1 Power consumption 2.8 Power specificationsSpinup power Idle mode power2.8.2 Conducted noise 2.8.1.1 Typical current profiles2.8.3 Voltage tolerance Figure 1. Typical 12V startup and operation current profileIdle and Standby timers 2.8.4 Power management modesActive mode Idle mode2.9.1 Drive case temperature 2.9 Environmental specifications2.9.2 Temperature gradient 2.9.3 Humidity 2.9.3.1 Relative humidity2.9.5.1 Operating shock 2.9.5 Shock2.9.5.2 Non-operating shock 2.9.6 Vibration2.10 Acoustics emissions Drive A-weighted Sound Power Levels SWL, BA2.11 Electromagnetic immunity Test for Prominent Discrete Tones PDTs2.12 Reliability 2.13.1 Safety certification2.13 Agency certification 2.12.1 Annualized Failure Rate AFR2.13.3 FCC verification Korean RRLAustralian C-Tick N176 2.15 Corrosive environment 2.14 Environmental protection“O”表示该部件（于同类物品程度上）所含的危险和有毒物质低于中国RoHS MCV标准所定义的门槛值。 “X”表示该部件（于同类物品程度上）所含的危险和有毒物质超出中国RoHS MCV标准所定义的门槛值。3.1 Handling and static-discharge precautions 3.0 Configuring and mounting the driveFigure 2. Attaching SATA cabling 3.2 Configuring the drive3.3 Serial ATA cables and connectors Figure 3. Mounting dimensions for 1000GB models 3.4 Drive mountingRecommended case temperature measurement location Figure 4. Mounting dimensions for 500, 320, 250 and 160GB models4.1 Hot-Plug compatibility 4.0 Serial ATA SATA interfaceSerial ATA connector pin definitions 4.2 Serial ATA device plug connector pin definitionsTable 8 Supported ATA commands 4.3 Supported ATA commandsPipeline HD.2 Series SATA Product Manual, Rev. E Firmware revision 8 ASCII character string, padded with blanks to end 4.3.1 Identify Device commandxx3FH xx07HTotal number of user-addressable LBA sectors available Refer to Sec IDLE IMMEDIATE command with IUNLOAD faeture is supported Set PIO mode to default and disable IORDY PIO mode 4.3.2 Set Features commandTable 9 Set Features command values Table 10 S.M.A.R.T. commands 4.3.3 S.M.A.R.T. commandsCode in features register S.M.A.R.T. commandOnline services 5.0 Seagate Technology support servicesWarranty Support Global Customer SupportUSA/Canada/Latin America support services Customer Service OperationsEurope, the Middle East and Africa Support Services Asia/Pacific Support ServicesIndex Page Page Pipeline HD.2 Series SATA Product Manual, Rev. E Page Seagate Technology LLC

Related manuals

Manual 48 pages 6.03 Kb