Seagate ST31000322CS Pipeline HD.2 Series SATA Product Manual, Rev. E, Word, Description, Value

Page 38

Word	Description	Value

	Total number of user-addressable LBA sectors available
	(Refer to Section 2.2 for related information.)
60–61	*Note: The maximum value allowed in this field is: 0FFFFFFFh	0FFFFFFFh*
60–61	(268,435,455 sectors, 137GB). Drives with capacities over 137GB will	0FFFFFFFh*
	have 0FFFFFFFh in this field and the actual number of user-address-
	able LBAs specified in words 100-103. This is required for drives that
	support the 48-bit addressing feature.
62	Retired	0000H
63	Multiword DMA active and modes supported (Refer to note following	xx07H
63	this table)	xx07H
64	Advanced PIO modes supported (modes 3 and 4 supported)	0003H
65	Minimum multiword DMA transfer cycle time per word (120 nsec)	0078H
66	Recommended multiword DMA transfer cycle time per word (120	0078H
66	nsec)	0078H
67	Minimum PIO cycle time without IORDY flow control (240 nsec)	00F0H
68	Minimum PIO cycle time with IORDY flow control (120 nsec)	0078H
69–74	ATA-reserved	0000H
75	Queue depth	0000H
76	Serial ATA capabilities	xxxxH
77	Reserved for future Serial ATA definition	xxxxH
78	Serial ATA features supported	xxxxH
79	Serial ATA features enabled	xxxxH
80	Major version number	003EH
81	Minor version number	0000H
82	Command sets supported	364BH
83	Command sets supported	7C03H
84	Command sets support extension (Refer to note following this table)	4003H	Refer to Word 108-111
84		note. (4003H =
		0100000000000011 binary)

85	Command sets enabled	30xxH
86	Command sets enabled	0001H
87	Command sets enable extension	4000H
88	Ultra DMA support and current mode (Refer to note following this	xx3FH
88	table)	xx3FH
89	Security erase time	0000H
90	Enhanced security erase time	0000H
92	Master password revision code	FFFEH
93	Hardware reset value	xxxxH
95–99	ATA-reserved	0000H

30	Pipeline HD.2 Series SATA Product Manual, Rev. E

Image 38

Contents Pipeline HD.2 Series SATA ST31000424CSST31000322CS ST3500414CSST3500312CSST3320413CSST3320310CS ST3250412CSST3250312CS ST3160316CS Product ManualDate Revision historyRevision Sheets affected or commentsPipeline HD.2 Series SATA Product Manual, Rev. E Pipeline HD.2 Series SATA Product Manual, Rev. E 3.0 Configuring and mounting the drive Contents2.0 Drive specifications 5.0 Seagate Technology support servicesPipeline HD.2 Series SATA Product Manual, Rev. E List of Figures Page 1.0 Introduction 1.1 About the Serial ATA interface 2.0 Drive specifications 2.1 Specification summary tablesST31000424CS Drive specifications summary for 1000GB modelsDrive specification ST31000322CSpage support.seagate.com/customer/warrantyvalidation.jsp Operational Shock maxST3500312CS Drive specifications summary for 500 and 320GB modelsST3500414CS ST3320413CSST3500414CS ST3250312CS Drive specifications summary for 250 and 160GB modelsST3250412CS ST3160316CSST3250312CS 2.4 Recording and interface technology 2.3 Default logical geometry2.2 Formatted capacity 2.2.1 LBA mode2.7 Start/stop times Physical characteristics2.6 Seek time 101.85mm / 4.010 inSpinup power 2.8 Power specifications2.8.1 Power consumption Idle mode power2.8.3 Voltage tolerance 2.8.1.1 Typical current profiles2.8.2 Conducted noise Figure 1. Typical 12V startup and operation current profileActive mode 2.8.4 Power management modesIdle and Standby timers Idle mode2.9.2 Temperature gradient 2.9 Environmental specifications2.9.1 Drive case temperature 2.9.3 Humidity 2.9.3.1 Relative humidity2.9.5.2 Non-operating shock 2.9.5 Shock2.9.5.1 Operating shock 2.9.6 Vibration2.11 Electromagnetic immunity Drive A-weighted Sound Power Levels SWL, BA2.10 Acoustics emissions Test for Prominent Discrete Tones PDTs2.13 Agency certification 2.13.1 Safety certification2.12 Reliability 2.12.1 Annualized Failure Rate AFR2.13.3 FCC verification Korean RRLAustralian C-Tick N176 “O”表示该部件（于同类物品程度上）所含的危险和有毒物质低于中国RoHS MCV标准所定义的门槛值。 2.14 Environmental protection2.15 Corrosive environment “X”表示该部件（于同类物品程度上）所含的危险和有毒物质超出中国RoHS MCV标准所定义的门槛值。3.0 Configuring and mounting the drive 3.1 Handling and static-discharge precautionsFigure 2. Attaching SATA cabling 3.2 Configuring the drive3.3 Serial ATA cables and connectors 3.4 Drive mounting Figure 3. Mounting dimensions for 1000GB modelsFigure 4. Mounting dimensions for 500, 320, 250 and 160GB models Recommended case temperature measurement location4.0 Serial ATA SATA interface 4.1 Hot-Plug compatibility4.2 Serial ATA device plug connector pin definitions Serial ATA connector pin definitions4.3 Supported ATA commands Table 8 Supported ATA commandsPipeline HD.2 Series SATA Product Manual, Rev. E 4.3.1 Identify Device command Firmware revision 8 ASCII character string, padded with blanks to endxx07H xx3FHTotal number of user-addressable LBA sectors available Refer to Sec IDLE IMMEDIATE command with IUNLOAD faeture is supported Set PIO mode to default and disable IORDY PIO mode 4.3.2 Set Features commandTable 9 Set Features command values Code in features register 4.3.3 S.M.A.R.T. commandsTable 10 S.M.A.R.T. commands S.M.A.R.T. commandWarranty Support 5.0 Seagate Technology support servicesOnline services Global Customer SupportEurope, the Middle East and Africa Support Services Customer Service OperationsUSA/Canada/Latin America support services Asia/Pacific Support ServicesIndex Page Page Pipeline HD.2 Series SATA Product Manual, Rev. E Page Seagate Technology LLC

Related manuals

Manual 48 pages 6.03 Kb