Seagate ST3250312CS, ST3250412CS manual IDLE IMMEDIATE command with IUNLOAD faeture is supported

Page 40
IDLE IMMEDIATE command with IUNLOAD faeture is supported.

 

13

IDLE IMMEDIATE command with IUNLOAD faeture is supported.

 

 

 

 

14

Shall be set to 1.

 

 

 

 

15

Shall be cleared to 0.

 

 

 

 

Bit

Word 88

 

 

 

 

0

Ultra DMA mode 0 is supported.

 

 

 

 

1

Ultra DMA mode 1 is supported.

 

 

 

 

2

Ultra DMA mode 2 is supported.

 

 

 

 

3

Ultra DMA mode 3 is supported.

 

 

 

 

4

Ultra DMA mode 4 is supported.

 

 

 

 

5

Ultra DMA mode 5 is supported.

 

 

 

 

6

Ultra DMA mode 6 is supported.

 

 

 

 

8

Ultra DMA mode 0 is currently active.

 

 

 

 

9

Ultra DMA mode 1 is currently active.

 

 

 

 

10

Ultra DMA mode 2 is currently active.

 

 

 

 

11

Ultra DMA mode 3 is currently active.

 

 

 

 

12

Ultra DMA mode 4 is currently active.

 

 

 

 

13

Ultra DMA mode 5 is currently active.

 

 

 

 

14

Ultra DMA mode 6 is currently active.

 

 

 

32

Pipeline HD.2 Series SATA Product Manual, Rev. E

Page 39 Page 41
Image 40
Page 39 Page 41
Contents ST31000424CSST31000322CS ST3500414CSST3500312CS ST3320413CSST3320310CS ST3250412CSST3250312CS ST3160316CSPipeline HD.2 Series SATA Product ManualRevision history RevisionDate Sheets affected or commentsPipeline HD.2 Series SATA Product Manual, Rev. E Pipeline HD.2 Series SATA Product Manual, Rev. E Contents 2.0 Drive specifications3.0 Configuring and mounting the drive 5.0 Seagate Technology support servicesPipeline HD.2 Series SATA Product Manual, Rev. E List of Figures Page 1.0 Introduction 1.1 About the Serial ATA interface 2.0 Drive specifications 2.1 Specification summary tablesDrive specifications summary for 1000GB models Drive specificationST31000424CS ST31000322CSpage support.seagate.com/customer/warrantyvalidation.jsp Operational Shock maxDrive specifications summary for 500 and 320GB models ST3500414CSST3500312CS ST3320413CSDrive specification Drive specifications summary for 250 and 160GB models ST3250412CSST3250312CS ST3160316CSDrive specification 2.3 Default logical geometry 2.2 Formatted capacity2.4 Recording and interface technology 2.2.1 LBA modePhysical characteristics 2.6 Seek time2.7 Start/stop times 101.85mm / 4.010 in2.8 Power specifications 2.8.1 Power consumptionSpinup power Idle mode power2.8.1.1 Typical current profiles 2.8.2 Conducted noise2.8.3 Voltage tolerance Figure 1. Typical 12V startup and operation current profile2.8.4 Power management modes Idle and Standby timersActive mode Idle mode2.9 Environmental specifications 2.9.1 Drive case temperature2.9.2 Temperature gradient 2.9.3 Humidity 2.9.3.1 Relative humidity2.9.5 Shock 2.9.5.1 Operating shock2.9.5.2 Non-operating shock 2.9.6 VibrationDrive A-weighted Sound Power Levels SWL, BA 2.10 Acoustics emissions2.11 Electromagnetic immunity Test for Prominent Discrete Tones PDTs2.13.1 Safety certification 2.12 Reliability2.13 Agency certification 2.12.1 Annualized Failure Rate AFRAustralian C-Tick N176 Korean RRL2.13.3 FCC verification 2.14 Environmental protection 2.15 Corrosive environment“O”表示该部件（于同类物品程度上）所含的危险和有毒物质低于中国RoHS MCV标准所定义的门槛值。 “X”表示该部件（于同类物品程度上）所含的危险和有毒物质超出中国RoHS MCV标准所定义的门槛值。3.0 Configuring and mounting the drive 3.1 Handling and static-discharge precautions3.3 Serial ATA cables and connectors 3.2 Configuring the driveFigure 2. Attaching SATA cabling 3.4 Drive mounting Figure 3. Mounting dimensions for 1000GB modelsFigure 4. Mounting dimensions for 500, 320, 250 and 160GB models Recommended case temperature measurement location4.0 Serial ATA SATA interface 4.1 Hot-Plug compatibility4.2 Serial ATA device plug connector pin definitions Serial ATA connector pin definitions4.3 Supported ATA commands Table 8 Supported ATA commandsCommand code in hex 4.3.1 Identify Device command Firmware revision 8 ASCII character string, padded with blanks to endxx07H xx3FHTotal number of user-addressable LBA sectors available Refer to Sec IDLE IMMEDIATE command with IUNLOAD faeture is supported Table 9 Set Features command values 4.3.2 Set Features commandSet PIO mode to default and disable IORDY PIO mode 4.3.3 S.M.A.R.T. commands Table 10 S.M.A.R.T. commandsCode in features register S.M.A.R.T. command5.0 Seagate Technology support services Online servicesWarranty Support Global Customer SupportCustomer Service Operations USA/Canada/Latin America support servicesEurope, the Middle East and Africa Support Services Asia/Pacific Support ServicesIndex Page Page Pipeline HD.2 Series SATA Product Manual, Rev. E Page Seagate Technology LLC
Related manuals
Manual 48 pages 6.03 Kb
Top Page Image Contents