Seagate ST940210A manual Serial ATA Sata Interface, Serial ATA connector pin definitions, Signal

Page 32

4.1Serial ATA (SATA) Interface

These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. The drive also supports the use of the IORDY signal to provide reliable high-speed data transfers.

For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification.

4.1.1Hot-Plug compatibility

LD25 Series SATA drives incorporate connectors which enable you to hot plug these drives in accordance with the Serial ATA: High Speed Serialized AT Attachment specification revision 2.0. This specification can be downloaded from http://www.serialata.com.

4.1.2Serial ATA device plug connector pin definitions

Table 7 summarizes the signals on the Serial ATA interface and power connectors..

Table 7:	Serial ATA connector pin definitions

Segment	Pin	Function	Definition

	S1	Ground	2nd mate

	S2	A+	Differential signal pair A from Phy

	S3	A-

	S4	Ground	2nd mate

	S5	B-	Differential signal pair B from Phy

	S6	B+
Signal
Signal	S7	Ground	2nd mate

Key and spacing separate signal and power segments

26	LD25 Series 5400.2 Product Manual, Rev. C

Image 32

Contents LD25 Series Page Contents Seagate Technology support services InterfaceList of Figures LD25 Series 5400.2 Product Manual, Rev. C Introduction Parallel ATA Pata Serial ATA SataLD25 Series 5400.2 Product Manual, Rev. C Drive specification ST980210A ST960210A ST940210A Specification summariesSpecification summary for ATA/PATA Parallel ATA models Following web Specifications for Sata Serial ATA models Default logical geometry LBA modeFormatted capacity Cylinders Read/write heads Sectors per track 16,383Physical characteristics Recording and interface technologySeek time Time to readyTypical seek times msec Read Write Time to ready Typical Max @ 25CPower specifications Voltage tolerance Typical current profileConducted noise Power-management modes Power management modesActive mode Idle modeEnvironmental specifications Shock Operating shockNonoperating shock VibrationAcoustics Electromagnetic immunityDrive level acoustics Electromagnetic immunitySafety certification Measurement type SpecificationReliability Agency certificationFCC verification Korean RRLAustralian C-Tick N176 European Union Restriction of Hazardous Substances RoHS Environmental protectionCorrosive environment LD25 Series 5400.2 Product Manual, Rev. C Handling and static-discharge precautions Mounting the driveMeasurements shown below are in inches Breather filter hole precautions Breather filter hole locationHow to configure the drive How to connect Sata cablesHow to use the cable-select option How to configure Parallel ATA Pata drivesHow to configure the drive as a master or slave LD25 Series 5400.2 Product Manual, Rev. C Interface Refer toSerial ATA connector pin definitions SignalSerial ATA Sata Interface Segment Pin Function DefinitionPin Function Definition P10 Ground 2nd mate P11 ReservedPata interface signals and connector pins Connector signalsConnector Cable Signal Name Contact Conductor Cable Connector Conductor Contact Signal NameSupported commands Command name Command code in hex ATA-standard commandsATA-standard security commands Command name Command code in hexATA-standard power-management commands Identify Device command Word Description ValueXxxxH Description if bit is set to Bit Word Bit WordUltra DMA mode 4 is supported Set Features command Set Features command valuesCode in features register A.R.T. command S.M.A.R.T. commandsM.A.R.T. commands Technical Support InternetPresales Support Data Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Index Page TMR LD25 Series 5400.2 Product Manual, Rev. C Page Seagate Technology LLC