Seagate ST980210AS, ST960210AS S.M.A.R.T. commands, Code in features register A.R.T. command

Page 42

4.6S.M.A.R.T. commands

S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive moni- tors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T. commands and implementation, see the Draft ATA-5 Standard.

SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4H) that elimi- nates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at: http://seatools.seagate.com.

This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the drive uses.

Table 10: S.M.A.R.T. commands

Code in features register	S.M.A.R.T. command

D0H	S.M.A.R.T. Read Data

D1H	Vendor-specific

D2H	S.M.A.R.T. Enable/Disable Attribute Autosave

D3H	S.M.A.R.T. Save Attribute Values

D4H	S.M.A.R.T. Execute Off-line Immediate (runs DST)

D5H	S.M.A.R.T. Read Log Sector

D6H	S.M.A.R.T. Write Log Sector

D7H	Vendor-specific

D8H	S.M.A.R.T. Enable Operations

D9H	S.M.A.R.T. Disable Operations

DAH	S.M.A.R.T. Return Status

Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x04 (abort) is written to the Error register.

36	LD25 Series 5400.2 Product Manual, Rev. C

Image 42

Contents LD25 Series Page Contents Seagate Technology support services InterfaceList of Figures LD25 Series 5400.2 Product Manual, Rev. C Introduction Parallel ATA Pata Serial ATA SataLD25 Series 5400.2 Product Manual, Rev. C Specification summaries Specification summary for ATA/PATA Parallel ATA modelsDrive specification ST980210A ST960210A ST940210A Following web Specifications for Sata Serial ATA models Formatted capacity Default logical geometryLBA mode Cylinders Read/write heads Sectors per track 16,383Physical characteristics Recording and interface technologyTypical seek times msec Read Write Seek timeTime to ready Time to ready Typical Max @ 25CPower specifications Typical current profile Conducted noiseVoltage tolerance Active mode Power-management modesPower management modes Idle modeEnvironmental specifications Nonoperating shock ShockOperating shock VibrationDrive level acoustics AcousticsElectromagnetic immunity Electromagnetic immunityReliability Safety certificationMeasurement type Specification Agency certificationKorean RRL Australian C-Tick N176FCC verification Environmental protection Corrosive environmentEuropean Union Restriction of Hazardous Substances RoHS LD25 Series 5400.2 Product Manual, Rev. C Handling and static-discharge precautions Mounting the driveMeasurements shown below are in inches Breather filter hole precautions Breather filter hole locationHow to configure the drive How to connect Sata cablesHow to configure Parallel ATA Pata drives How to configure the drive as a master or slaveHow to use the cable-select option LD25 Series 5400.2 Product Manual, Rev. C Interface Refer toSerial ATA Sata Interface Serial ATA connector pin definitionsSignal Segment Pin Function DefinitionPin Function Definition P10 Ground 2nd mate P11 ReservedConnector Cable Signal Name Contact Conductor Pata interface signals and connector pinsConnector signals Cable Connector Conductor Contact Signal NameSupported commands Command name Command code in hex ATA-standard commandsCommand name Command code in hex ATA-standard power-management commandsATA-standard security commands Identify Device command Word Description ValueXxxxH Description if bit is set to Bit Word Bit WordUltra DMA mode 4 is supported Set Features command Set Features command valuesS.M.A.R.T. commands M.A.R.T. commandsCode in features register A.R.T. command Internet Presales SupportTechnical Support Warranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Index Page TMR LD25 Series 5400.2 Product Manual, Rev. C Page Seagate Technology LLC