Seagate ST980210A Supported commands, Command name Command code in hex ATA-standard commands

Page 35

4.3Supported commands

The following table lists the standard commands that the drive supports. See “S.M.A.R.T. commands” on page 36.for details and subcommands used in the S.M.A.R.T. implementation.

Command name	Command code (in hex)

ATA-standard commands

Device Configuration Restore	B1h/C0h

Device Configuration Freeze Lock	B1h/C1h

Device Configuration Identify	B1h/C2h

Device Configuration Set	B1h/C3h

Download Microcode	92h

Execute Device Diagnostics	90h

Flush Cache	E7h

Flush Cache Extended	EAh

Identify Device	ECh

Initialize Device Parameters	91h

Read Buffer	E4h

Read DMA	C8h

Read DMA Extended	25h

Read DMA without Retries	C9h

Read Long with Retries	22h

Read Long without Retries	23h

Read Multiple	C4h

Read Multiple Extended	29h

Read Native Max Address	F8h

Read Native Max Address Extended	27h

Read Sectors	20h

Read Sectors Extended	24h

Read Sectors without Retries	21h

Read Verify Sectors	40h

Read Verify Sectors Extended	42h

Read Verify Sectors without Retries	41h

Seek	70h

Set Features	EFh

Set Max Address	F9h

LD25 Series 5400.2 Product Manual, Rev. C

29

Image 35

Contents LD25 Series Page Contents Interface Seagate Technology support servicesList of Figures LD25 Series 5400.2 Product Manual, Rev. C Parallel ATA Pata Serial ATA Sata IntroductionLD25 Series 5400.2 Product Manual, Rev. C Drive specification ST980210A ST960210A ST940210A Specification summariesSpecification summary for ATA/PATA Parallel ATA models Following web Specifications for Sata Serial ATA models Cylinders Read/write heads Sectors per track 16,383 Default logical geometryLBA mode Formatted capacityRecording and interface technology Physical characteristicsTime to ready Typical Max @ 25C Seek timeTime to ready Typical seek times msec Read WritePower specifications Voltage tolerance Typical current profileConducted noise Idle mode Power-management modesPower management modes Active modeEnvironmental specifications Vibration ShockOperating shock Nonoperating shockElectromagnetic immunity AcousticsElectromagnetic immunity Drive level acousticsAgency certification Safety certificationMeasurement type Specification ReliabilityFCC verification Korean RRLAustralian C-Tick N176 European Union Restriction of Hazardous Substances RoHS Environmental protectionCorrosive environment LD25 Series 5400.2 Product Manual, Rev. C Mounting the drive Handling and static-discharge precautionsMeasurements shown below are in inches Breather filter hole location Breather filter hole precautionsHow to connect Sata cables How to configure the driveHow to use the cable-select option How to configure Parallel ATA Pata drivesHow to configure the drive as a master or slave LD25 Series 5400.2 Product Manual, Rev. C Refer to InterfaceSegment Pin Function Definition Serial ATA connector pin definitionsSignal Serial ATA Sata InterfaceP10 Ground 2nd mate P11 Reserved Pin Function DefinitionCable Connector Conductor Contact Signal Name Pata interface signals and connector pinsConnector signals Connector Cable Signal Name Contact ConductorCommand name Command code in hex ATA-standard commands Supported commandsATA-standard security commands Command name Command code in hexATA-standard power-management commands Word Description Value Identify Device commandXxxxH Bit Word Description if bit is set to Bit WordUltra DMA mode 4 is supported Set Features command values Set Features commandCode in features register A.R.T. command S.M.A.R.T. commandsM.A.R.T. commands Technical Support InternetPresales Support Data Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Index Page TMR LD25 Series 5400.2 Product Manual, Rev. C Page Seagate Technology LLC