Seagate ST980210AS manual Command name Command code in hex, ATA-standard power-management commands

Page 36

Command name	Command code (in hex)

Note: Individual Set Max commands are	Address:	00H
identified by the value placed in the Set Max	Password:	01H
Features register as defined to the right.	Lock:	02H
	Unlock:	03H
	Freeze Lock:	04H
Set Multiple Mode	C6h

S.M.A.R.T. Disable Operations	B0h/D9h

S.M.A.R.T. Enable/Disable Autosave	B0h/D2h

S.M.A.R.T. Enable Operations	B0h/D8h

S.M.A.R.T. Enable/Disable Auto Offline	B0h/DBh

S.M.A.R.T. Enable One Attribute Modifica-	B0h/E0h
tion

S.M.A.R.T. Execute Offline	B0h/D4h

S.M.A.R.T. Read Attribute Thresholds	B0h/D1h

S.M.A.R.T. Read Data	B0h/D0h

S.M.A.R.T. Read Log Sector	B0h/D5h

S.M.A.R.T. Return Status	B0h/DAh

S.M.A.R.T. Save Attribute Values	B0h/D3h

S.M.A.R.T. Write Attribute Thresholds	B0h/D7h

S.M.A.R.T. Write Attribute Values	B0h/E1h

S.M.A.R.T. Write Log Sector	B0h/D6h

Write Buffer	E8h

Write DMA	CAh

Write DMA Extended	35h

Write DMA without Retries	CBh

Write Long with Retries	32h

Write Long without Retries	33h

Write Multiple	C5h

Write Sectors	30h, 31h
Write Sectors Extended	34h

ATA-standard power-management commands

Check Power Mode	98h or E5h

Idle	97h or E3h

Idle Immediate	95h or E1h

Sleep	99h or E6h

Standby	96h or E2h

Standby Immediate	94h or E0h

ATA-standard security commands

30	LD25 Series 5400.2 Product Manual, Rev. C

Image 36

Contents LD25 Series Page Contents Seagate Technology support services InterfaceList of Figures LD25 Series 5400.2 Product Manual, Rev. C Introduction Parallel ATA Pata Serial ATA SataLD25 Series 5400.2 Product Manual, Rev. C Specification summaries Specification summary for ATA/PATA Parallel ATA modelsDrive specification ST980210A ST960210A ST940210A Following web Specifications for Sata Serial ATA models Default logical geometry LBA modeFormatted capacity Cylinders Read/write heads Sectors per track 16,383Physical characteristics Recording and interface technologySeek time Time to readyTypical seek times msec Read Write Time to ready Typical Max @ 25CPower specifications Typical current profile Conducted noiseVoltage tolerance Power-management modes Power management modesActive mode Idle modeEnvironmental specifications Shock Operating shockNonoperating shock VibrationAcoustics Electromagnetic immunityDrive level acoustics Electromagnetic immunitySafety certification Measurement type SpecificationReliability Agency certificationKorean RRL Australian C-Tick N176FCC verification Environmental protection Corrosive environmentEuropean Union Restriction of Hazardous Substances RoHS LD25 Series 5400.2 Product Manual, Rev. C Handling and static-discharge precautions Mounting the driveMeasurements shown below are in inches Breather filter hole precautions Breather filter hole locationHow to configure the drive How to connect Sata cablesHow to configure Parallel ATA Pata drives How to configure the drive as a master or slaveHow to use the cable-select option LD25 Series 5400.2 Product Manual, Rev. C Interface Refer toSerial ATA connector pin definitions SignalSerial ATA Sata Interface Segment Pin Function DefinitionPin Function Definition P10 Ground 2nd mate P11 ReservedPata interface signals and connector pins Connector signalsConnector Cable Signal Name Contact Conductor Cable Connector Conductor Contact Signal NameSupported commands Command name Command code in hex ATA-standard commandsCommand name Command code in hex ATA-standard power-management commandsATA-standard security commands Identify Device command Word Description ValueXxxxH Description if bit is set to Bit Word Bit WordUltra DMA mode 4 is supported Set Features command Set Features command valuesS.M.A.R.T. commands M.A.R.T. commandsCode in features register A.R.T. command Internet Presales SupportTechnical Support Warranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Index Page TMR LD25 Series 5400.2 Product Manual, Rev. C Page Seagate Technology LLC