Seagate ST980210AS, ST960210AS manual Reliability, Agency certification, Safety certification

Page 21

2.12

Reliability

 

 

 

Measurement type

Specification

 

 

Nonrecoverable read errors

1 per 1014 bits read, max.

Annualized Failure Rate (AFR)

<0.6% (Desktop and gaming: 2400 power-on-hours)

 

 

<2.0% (PVR/DVR: 8760 power-on-hours)

 

 

Load/Unload (L/UL)

 

Controlled L/UL cycles

50,000

(40°C, 50% Relative Humidity)

 

Emergency L/UL cycles

20,000

(40°C, 50% Relative Humidity)

 

 

 

 

Warranty

 

To determine the warranty for a specific drive, use a web browser to access the fol-

 

 

lowing web page:

 

 

www.seagate.com/support/service/

 

 

From this page, click on the “Verify Your Warranty” link. You will be asked to pro-

 

 

vide the drive serial number, model number (or part number) and country of pur-

 

 

chase. The system will display the warranty information for your drive.

 

 

 

2.13Agency certification

2.13.1Safety certification

The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections of IEC950 and EN 60950 as tested by TUV North America.

2.13.2Electromagnetic compatibility

Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec- tromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN 55024.

Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators should confirm EMC compliance and provide CE marking for their products.

LD25 Series 5400.2 Product Manual, Rev. C

15

Page 20 Page 22
Image 21
Page 20 Page 22
Contents LD25 Series Page Contents Interface Seagate Technology support servicesList of Figures LD25 Series 5400.2 Product Manual, Rev. C Parallel ATA Pata Serial ATA Sata IntroductionLD25 Series 5400.2 Product Manual, Rev. C Specification summaries Specification summary for ATA/PATA Parallel ATA modelsDrive specification ST980210A ST960210A ST940210A Following web Specifications for Sata Serial ATA models LBA mode Default logical geometryFormatted capacity Cylinders Read/write heads Sectors per track 16,383Recording and interface technology Physical characteristicsTime to ready Seek timeTypical seek times msec Read Write Time to ready Typical Max @ 25CPower specifications Typical current profile Conducted noiseVoltage tolerance Power management modes Power-management modesActive mode Idle modeEnvironmental specifications Operating shock ShockNonoperating shock VibrationElectromagnetic immunity AcousticsDrive level acoustics Electromagnetic immunityMeasurement type Specification Safety certificationReliability Agency certificationKorean RRL Australian C-Tick N176FCC verification Environmental protection Corrosive environmentEuropean Union Restriction of Hazardous Substances RoHS LD25 Series 5400.2 Product Manual, Rev. C Mounting the drive Handling and static-discharge precautionsMeasurements shown below are in inches Breather filter hole location Breather filter hole precautionsHow to connect Sata cables How to configure the driveHow to configure Parallel ATA Pata drives How to configure the drive as a master or slaveHow to use the cable-select option LD25 Series 5400.2 Product Manual, Rev. C Refer to InterfaceSignal Serial ATA connector pin definitionsSerial ATA Sata Interface Segment Pin Function DefinitionP10 Ground 2nd mate P11 Reserved Pin Function DefinitionConnector signals Pata interface signals and connector pinsConnector Cable Signal Name Contact Conductor Cable Connector Conductor Contact Signal NameCommand name Command code in hex ATA-standard commands Supported commandsCommand name Command code in hex ATA-standard power-management commandsATA-standard security commands Word Description Value Identify Device commandXxxxH Bit Word Description if bit is set to Bit WordUltra DMA mode 4 is supported Set Features command values Set Features commandS.M.A.R.T. commands M.A.R.T. commandsCode in features register A.R.T. command Internet Presales SupportTechnical Support Warranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Index Page TMR LD25 Series 5400.2 Product Manual, Rev. C Page Seagate Technology LLC
Top Page Image Contents