Seagate ST1000NM0021, ST1000NM0001 manual Start/stop time, General performance characteristics

Page 19

5.2.2Format command execution time for 512-byte sectors (minutes)

 

2TB models

1TB models

500GB models

Maximum (with verify)

627

345

173

 

 

 

Maximum (without verify)

314

173

86

 

 

 

Execution time measured from receipt of the last byte of the Command Descriptor Block (CDB) to the request for a Status Byte Transfer to the Initiator (excluding connect/disconnect).

When changing sector sizes, the format times shown above may need to be increased by 30 minutes.

5.2.3General performance characteristics

Minimum sector interleave

1 to 1

Data buffer to/from disk media (one 512-byte logical block)*

95 to 212 MB/s

Sustained transfer rate

60 to 147 MB/s

SAS Interface maximum instantaneous transfer rate

600MB/s* per port

 

(dual port = 1200MB/s*)

Logical block sizes

 

512 (default), 520 or 528.

 

Read/write consecutive sectors on a track

Yes

Flaw reallocation performance impact (for flaws reallocated at format time using the

Negligible

spare sectors per sparing zone reallocation scheme.)

 

Average rotational latency

4.16ms

*Assumes no errors and no relocated logical blocks. Rate measured from the start of the first logical block transfer to or from the host.

5.3Start/stop time

The drive accepts the commands listed in the SAS Interface Manual less than 3 seconds after DC power has been applied.

If the drive receives a NOTIFY (ENABLE SPINUP) primitive through either port and has not received a START STOP UNIT command with the START bit equal to 0, the drive becomes ready for normal operations within 30 seconds (excluding the error recovery procedure).

If the drive receives a START STOP UNIT command with the START bit equal to 0 before receiving a NOTIFY (ENABLE SPINUP) primitive, the drive waits for a START STOP UNIT command with the START bit equal to 1. After receiving a START STOP UNIT command with the START bit equal to 1, the drive waits for a NOTIFY (ENABLE SPINUP) primitive. After receiving a NOTIFY (ENABLE SPINUP) primitive through either port, the drive becomes ready for normal operations within 30 seconds (excluding the error recovery procedure).

If the drive receives a START STOP UNIT command with the START bit and IMMED bit equal to 1 and does not receive a NOTIFY (ENABLE SPINUP) primitive within 5 seconds, the drive fails the START STOP UNIT command.

The START STOP UNIT command may be used to command the drive to stop the spindle. Stop time is 20 sec- onds (maximum) from removal of DC power. SCSI stop time is 20 seconds. There is no power control switch on the drive.

Constellation ES.1 SAS Product Manual, Rev. E

11

Downloaded from www.Manualslib.com manuals search engine

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Standard Models Self-Encrypting Drive Models ST1000NM0041 ST500NM0041SED Fips 140-2 Models ST2000NM0041 Revision history Contents Interface requirements Defect and error managementInstallation About Fips About self-encrypting drivesPage Constellation ES.1 SAS Product Manual, Rev. E List of Figures Constellation ES.1 SAS Product Manual, Rev. E Seagate Online Support and Services Seagate Technology support servicesModel Number Self-Encrypting Drive SED Fips 140-2 Level ScopeElectromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityKorean KCC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickChina Restriction of Hazardous Substances RoHS Directive European Union Restriction of Hazardous Substances RoHSSelf-Encrypting Drives Reference Manual Reference documentsGeneral description Media description Standard featuresPerformance Programmable drive capacity Factory-installed optionsReliability Formatted capacitiesAccess time Performance characteristicsInternal drive characteristics Seek performance characteristicsStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataUnrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsReporting control 4 S.M.A.R.TControlling S.M.A.R.T Performance impactPredictive failures Temperature Log Page 0Dh Parameter Code DescriptionThermal monitor Implementation State of the drive prior to testingDrive Self Test DST DST failure definitionLog page entries Short and extended testsShort test Function Code 001b Extended test Function Code 010bProduct repair and return information Product warrantyShipping StoragePowerChoiceTM power management Physical/electrical specificationsPowerChoice modes DC power requirements AC power requirementsRegulation ±5% Constellation ES.1 SAS Product Manual, Rev. E Constellation ES.1 SAS Product Manual, Rev. E Power sequencing General DC power requirement notesConducted noise immunity TB model current profiles Current profilesConstellation ES.1 SAS Product Manual, Rev. E GB model current profiles 2TB models in 3Gb operation Power dissipation2TB models in 6Gb operation 1TB models in 3Gb operation 1TB models in 6Gb operation 500GB models in 3Gb operation 500GB models in 6Gb operation Environmental limits Temperature a. OperatingRelative humidity Shock and vibration Effective altitude sea level a. OperatingShock Recommended mounting Vibration a. Operating-normalAcoustics Air cleanlinessCorrosive environment Mounting configuration dimensions Mechanical specificationsSeagate Enterprise SED About FipsPurpose Validation ProgramExample of Fips tamper evidence labels Data encryption Controlled accessAdmin SP About self-encrypting drivesData bands Authenticated firmware downloadRandom number generator RNG Drive lockingRevertSP Power requirementsSupported commands Sanitize Cryptographic EraseDrive internal defects/errors Defect and error managementDrive error recovery procedures SAS system errors Media Pre-Scan Background Media ScanDeferred Auto-Reallocation Levels of PI Setting and determining the current Type LevelIdle Read After Write Protection Information PIIdentifying a Protection Information drive Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Inquiry data Mode Sense dataConstellation ES.1 inquiry data Page Mode Sense data changeable and default values for 2TB drives Mode Sense data changeable and default values for 1TB drives 3a 38 60 30 00 00 02 Miscellaneous features Miscellaneous operating features and conditionsMiscellaneous status SAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out Signal characteristicsPower SAS transmitters and receiversGeneral interface characteristics SAS-2 Specification ComplianceLED drive signal Differential signalsConstellation ES.1 SAS Product Manual, Rev. E Numerics IndexKCC Msid Mtbf See also cooling Page Constellation ES.1 SAS Product Manual, Rev. E Page Americas Seagate Technology LLC

ST2000NM0001, ST1000NM0041, ST500NM0001, ST2000NM0021, ST1000NM0021 specifications

Seagate is a renowned leader in data storage solutions, offering a wide array of hard disk drives (HDDs) suitable for various applications. Among their product lineup, the Seagate ST2000NM0041, ST500NM0021, ST500NM0041, ST1000NM0001, and ST1000NM0021 stand out as reliable options tailored for enterprise environments and general storage needs.

The Seagate ST2000NM0041 is a 2TB 7200 RPM drive designed for high-performance workloads in data centers. One of its key features is the use of the SATA III interface, providing data transfer speeds of up to 6 Gbps, ensuring quick access to data. This model supports advanced error recovery controls and features enhanced power management capabilities, which contribute to its reliable performance and energy efficiency.

Next, the ST500NM0021 and ST500NM0041 are both 500GB drives that cater to different consumer needs. The ST500NM0021 is a 5400 RPM drive, typically used in scenarios where lower power consumption is vital, such as in compact systems or external storage configurations. Its efficient design enables quieter operation, making it ideal for environments that require minimal noise. Conversely, the ST500NM0041 operates at a speed of 7200 RPM, making it suitable for more demanding applications that require swift read and write speeds. Both models utilize Serial ATA for connectivity, ensuring compatibility with a wide range of systems.

The ST1000NM0001 and ST1000NM0021 are 1TB drives that provide versatility across different platforms. Similar to their 500GB counterparts, the ST1000NM0001 features a 7200 RPM speed, optimizing performance for applications requiring faster data processing. In contrast, the ST1000NM0021 operates at 5400 RPM, designed for users prioritizing energy efficiency over speed, like in desktop and external storage solutions. Each of these drives supports advanced technologies such as Native Command Queuing (NCQ), which enhances performance by allowing multiple commands to be executed simultaneously.

Overall, the Seagate ST series hard drives offer flexible storage options for a variety of applications. With their robust features, including varied RPM speeds, power management, and compatibility with SATA connections, these drives cater to the needs of both consumer and enterprise markets, establishing Seagate as a trusted provider in the storage arena.
Top Page Image Contents