Seagate ST1000NM0041, ST1000NM0001, ST1000NM0021 Acoustics, Air cleanliness, Corrosive environment

Page 47

c.Non-operating

The limits of non-operating vibration shall apply to all conditions of handling and transportation. This includes both isolated drives and integrated drives.

The drive shall not incur physical damage or degraded performance as a result of continuous vibration not exceeding

5 - 22 Hz

2 Gs (0 to peak, linear, swept sine, 0.5 octave/min)

22 - 350 Hz

5 Gs (0 to peak, linear, swept sine, 0.5 octave/min)

350 - 500 Hz

2 Gs (0 to peak, linear, swept sine, 0.5 octave/min)

Vibration may be applied in the X, Y, or Z axis.

7.5.5Acoustics

Sound power during idle mode shall be 2.7 bels typical when measured to ISO 7779 specification. Sound power while operating shall be 3.0 bels typical when measured to ISO 7779 specification.

There will not be any discrete tones more than 10 dB above the masking noise on typical drives when mea- sured according to Seagate specification 30553-001. There will not be any tones more than 24 dB above the masking noise on any drive.

7.5.6Air cleanliness

The drive is designed to operate in a typical office environment with minimal environmental control.

7.5.7Corrosive environment

Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated testing cannot duplicate every potential application environment.

Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corro- sive chemicals as electronic drive component reliability can be affected by the installation environment. The sil- ver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulca- nized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.

7.5.8Electromagnetic susceptibility

See Section 3.1.1.1.

Constellation ES.1 SAS Product Manual, Rev. E

39

Downloaded from www.Manualslib.com manuals search engine

Page 46 Page 48
Image 47
Page 46 Page 48
Contents SED Fips 140-2 Models ST2000NM0041 ST1000NM0041 ST500NM0041Standard Models Self-Encrypting Drive Models Revision history Contents Interface requirements Defect and error managementInstallation About Fips About self-encrypting drivesPage Constellation ES.1 SAS Product Manual, Rev. E List of Figures Constellation ES.1 SAS Product Manual, Rev. E Seagate Online Support and Services Seagate Technology support servicesModel Number Self-Encrypting Drive SED Fips 140-2 Level ScopeElectromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityKorean KCC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickChina Restriction of Hazardous Substances RoHS Directive European Union Restriction of Hazardous Substances RoHSSelf-Encrypting Drives Reference Manual Reference documentsGeneral description Performance Standard featuresMedia description Programmable drive capacity Factory-installed optionsReliability Formatted capacitiesAccess time Performance characteristicsInternal drive characteristics Seek performance characteristicsStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataUnrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsReporting control 4 S.M.A.R.TControlling S.M.A.R.T Performance impactThermal monitor Temperature Log Page 0Dh Parameter Code DescriptionPredictive failures Implementation State of the drive prior to testingDrive Self Test DST DST failure definitionLog page entries Short and extended testsShort test Function Code 001b Extended test Function Code 010bProduct repair and return information Product warrantyShipping StoragePowerChoice modes Physical/electrical specificationsPowerChoiceTM power management DC power requirements AC power requirementsRegulation ±5% Constellation ES.1 SAS Product Manual, Rev. E Constellation ES.1 SAS Product Manual, Rev. E Conducted noise immunity General DC power requirement notesPower sequencing TB model current profiles Current profilesConstellation ES.1 SAS Product Manual, Rev. E GB model current profiles 2TB models in 3Gb operation Power dissipation2TB models in 6Gb operation 1TB models in 3Gb operation 1TB models in 6Gb operation 500GB models in 3Gb operation 500GB models in 6Gb operation Relative humidity Temperature a. Operating Environmental limits Shock Effective altitude sea level a. OperatingShock and vibration Recommended mounting Vibration a. Operating-normalCorrosive environment Air cleanlinessAcoustics Mounting configuration dimensions Mechanical specificationsSeagate Enterprise SED About FipsPurpose Validation ProgramExample of Fips tamper evidence labels Data encryption Controlled accessAdmin SP About self-encrypting drivesData bands Authenticated firmware downloadRandom number generator RNG Drive lockingRevertSP Power requirementsSupported commands Sanitize Cryptographic EraseDrive error recovery procedures Defect and error managementDrive internal defects/errors SAS system errors Deferred Auto-Reallocation Background Media ScanMedia Pre-Scan Levels of PI Setting and determining the current Type LevelIdle Read After Write Protection Information PIIdentifying a Protection Information drive Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Constellation ES.1 inquiry data Mode Sense dataInquiry data Page Mode Sense data changeable and default values for 2TB drives Mode Sense data changeable and default values for 1TB drives 3a 38 60 30 00 00 02 Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features SAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out Signal characteristicsPower SAS transmitters and receiversGeneral interface characteristics SAS-2 Specification ComplianceLED drive signal Differential signalsConstellation ES.1 SAS Product Manual, Rev. E Numerics IndexKCC Msid Mtbf See also cooling Page Constellation ES.1 SAS Product Manual, Rev. E Page Americas Seagate Technology LLC
Top Page Image Contents