Seagate ST2000NM0001, ST1000NM0001, ST1000NM0021, ST1000NM0041 manual Installation, Drive orientation

Page 59

11.0Installation

Constellation ES.1 disk drive installation is a plug-and-play process. There are no jumpers, switches, or termi- nators on the drive.

SAS drives are designed to be used in a host system that provides a SAS-compatible backplane with bays designed to accommodate the drive. In such systems, the host system typically provides a carrier or tray into which you need to mount the drive. Mount the drive to the carrier or tray provided by the host system using four M3 x 0.5 metric screws. When tightening the screws, use a maximum torque of 4.5 in-lb +/- 0.45 in-lb. Do not over-tighten or force the screws. You can mount the drive in any orientation.

Note. SAS drives are designed to be attached to the host system without I/O or power cables. If you intend the use the drive in a non-backplane host system, connecting the drive using high-quality cables is acceptable as long as the I/O cable length does not exceed 4 meters (13.1 feet).

Slide the carrier or tray into the appropriate bay in your host system using the instructions provided by the host system. This connects the drive directly to your system’s SAS connector. The SAS connector is normally located on a SAS backpanel. See Section 12.4.1 for additional information about these connectors.

Power is supplied through the SAS connector.

The drive is shipped from the factory low-level formatted in 512-byte logical blocks. You need to reformat the drive only if you want to select a different logical block size.

Figure 14. Physical interface

11.1Drive orientation

The drive may be mounted in any orientation. All drive performance characterizations, however, have been done with the drive in horizontal (discs level) and vertical (drive on its side) orientations, which are the two pre- ferred mounting orientations.

Constellation ES.1 SAS Product Manual, Rev. E

51

Downloaded from www.Manualslib.com manuals search engine

Image 59

Contents SED Fips 140-2 Models ST2000NM0041 ST1000NM0041 ST500NM0041Standard Models Self-Encrypting Drive Models Revision history Contents Interface requirements Defect and error managementInstallation About Fips About self-encrypting drivesPage Constellation ES.1 SAS Product Manual, Rev. E List of Figures Constellation ES.1 SAS Product Manual, Rev. E Seagate Online Support and Services Seagate Technology support servicesModel Number Self-Encrypting Drive SED Fips 140-2 Level ScopeElectromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityKorean KCC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickChina Restriction of Hazardous Substances RoHS Directive European Union Restriction of Hazardous Substances RoHSSelf-Encrypting Drives Reference Manual Reference documentsGeneral description Performance Standard featuresMedia description Programmable drive capacity Factory-installed optionsReliability Formatted capacitiesAccess time Performance characteristicsInternal drive characteristics Seek performance characteristicsStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataUnrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsReporting control 4 S.M.A.R.TControlling S.M.A.R.T Performance impactThermal monitor Temperature Log Page 0Dh Parameter Code DescriptionPredictive failures Implementation State of the drive prior to testingDrive Self Test DST DST failure definitionLog page entries Short and extended testsShort test Function Code 001b Extended test Function Code 010bProduct repair and return information Product warrantyShipping StoragePowerChoice modes Physical/electrical specificationsPowerChoiceTM power management DC power requirements AC power requirementsRegulation ±5% Constellation ES.1 SAS Product Manual, Rev. E Constellation ES.1 SAS Product Manual, Rev. E Conducted noise immunity General DC power requirement notesPower sequencing TB model current profiles Current profilesConstellation ES.1 SAS Product Manual, Rev. E GB model current profiles 2TB models in 3Gb operation Power dissipation2TB models in 6Gb operation 1TB models in 3Gb operation 1TB models in 6Gb operation 500GB models in 3Gb operation 500GB models in 6Gb operation Relative humidity Temperature a. OperatingEnvironmental limits Shock Effective altitude sea level a. OperatingShock and vibration Recommended mounting Vibration a. Operating-normalCorrosive environment Air cleanlinessAcoustics Mounting configuration dimensions Mechanical specificationsSeagate Enterprise SED About FipsPurpose Validation ProgramExample of Fips tamper evidence labels Data encryption Controlled accessAdmin SP About self-encrypting drivesData bands Authenticated firmware downloadRandom number generator RNG Drive lockingRevertSP Power requirementsSupported commands Sanitize Cryptographic EraseDrive error recovery procedures Defect and error managementDrive internal defects/errors SAS system errors Deferred Auto-Reallocation Background Media Scan Media Pre-Scan Levels of PI Setting and determining the current Type LevelIdle Read After Write Protection Information PIIdentifying a Protection Information drive Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Constellation ES.1 inquiry data Mode Sense dataInquiry data Page Mode Sense data changeable and default values for 2TB drives Mode Sense data changeable and default values for 1TB drives 3a 38 60 30 00 00 02 Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features SAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out Signal characteristicsPower SAS transmitters and receiversGeneral interface characteristics SAS-2 Specification ComplianceLED drive signal Differential signalsConstellation ES.1 SAS Product Manual, Rev. E Numerics IndexKCC Msid Mtbf See also cooling Page Constellation ES.1 SAS Product Manual, Rev. E Page Americas Seagate Technology LLC