Seagate ST500NM0041, ST1000NM0001, ST1000NM0021, ST1000NM0041, ST2000NM0041, ST2000NM0021, ST2000NM0001

Page 69

Saved values are stored on the drive’s media using a Mode Select command. Only parameter values that are allowed to be changed can be changed by this method. Parameters in the saved values list that are not changeable by the Mode Select command get their values from default values storage.

When power is applied to the drive, it takes saved values from the media and stores them as current val- ues in volatile memory. It is not possible to change the current values (or the saved values) with a Mode Select command before the drive achieves operating speed and is “ready.” An attempt to do so results in a “Check Condition” status.

On drives requiring unique saved values, the required unique saved values are stored into the saved val- ues storage location on the media prior to shipping the drive. Some drives may have unique firmware with unique default values also.

On standard OEM drives, the saved values are taken from the default values list and stored into the saved values storage location on the media prior to shipping.

3.Current values

Current values are volatile values being used by the drive to control its operation. A Mode Select command can be used to change the values identified as changeable values. Originally, current values are installed from saved or default values after a power on reset, hard reset, or Bus Device Reset message.

4.Changeable values

Changeable values form a bit mask, stored in nonvolatile memory, that dictates which of the current values and saved values can be changed by a Mode Select command. A one (1) indicates the value can be changed. A zero (0) indicates the value is not changeable. For example, in Table 10, refer to Mode page 81, in the row entitled “CHG.” These are hex numbers representing the changeable values for Mode page

81.Note in columns 5 and 6 (bytes 04 and 05), there is 00h which indicates that in bytes 04 and 05 none of the bits are changeable. Note also that bytes 06, 07, 09, 10, and 11 are not changeable, because those fields are all zeros. In byte 02, hex value FF equates to the binary pattern 11111111. If there is a zero in any bit position in the field, it means that bit is not changeable. Since all of the bits in byte 02 are ones, all of these bits are changeable.

The changeable values list can only be changed by downloading new firmware into the flash E-PROM.

Note. Because there are often several different versions of drive control firmware in the total population of drives in the field, the Mode Sense values given in the following tables may not exactly match those of some drives.

The following tables list the values of the data bytes returned by the drive in response to the Mode Sense com- mand pages for SCSI implementation (see the SAS Interface Manual).

DEF = Default value. Standard OEM drives are shipped configured this way.

CHG = Changeable bits; indicates if default value is changeable.

Constellation ES.1 SAS Product Manual, Rev. E

61

Downloaded from www.Manualslib.com manuals search engine

Page 68 Page 70
Image 69
Page 68 Page 70
Contents ST1000NM0041 ST500NM0041 Standard Models Self-Encrypting Drive ModelsSED Fips 140-2 Models ST2000NM0041 Revision history Contents Installation Defect and error managementAbout Fips About self-encrypting drives Interface requirementsPage Constellation ES.1 SAS Product Manual, Rev. E List of Figures Constellation ES.1 SAS Product Manual, Rev. E Seagate Online Support and Services Seagate Technology support servicesModel Number Self-Encrypting Drive SED Fips 140-2 Level ScopeStandards Applicable standards and reference documentationElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance for the European Union Electromagnetic complianceAustralian C-Tick Korean KCCChina Restriction of Hazardous Substances RoHS Directive European Union Restriction of Hazardous Substances RoHSSelf-Encrypting Drives Reference Manual Reference documentsGeneral description Standard features Media descriptionPerformance Reliability Factory-installed optionsFormatted capacities Programmable drive capacityInternal drive characteristics Performance characteristicsSeek performance characteristics Access timeStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataError rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenanceControlling S.M.A.R.T 4 S.M.A.R.TPerformance impact Reporting controlTemperature Log Page 0Dh Parameter Code Description Predictive failuresThermal monitor Drive Self Test DST State of the drive prior to testingDST failure definition ImplementationShort test Function Code 001b Short and extended testsExtended test Function Code 010b Log page entriesShipping Product warrantyStorage Product repair and return informationPhysical/electrical specifications PowerChoiceTM power managementPowerChoice modes DC power requirements AC power requirementsRegulation ±5% Constellation ES.1 SAS Product Manual, Rev. E Constellation ES.1 SAS Product Manual, Rev. E General DC power requirement notes Power sequencingConducted noise immunity TB model current profiles Current profilesConstellation ES.1 SAS Product Manual, Rev. E GB model current profiles 2TB models in 3Gb operation Power dissipation2TB models in 6Gb operation 1TB models in 3Gb operation 1TB models in 6Gb operation 500GB models in 3Gb operation 500GB models in 6Gb operation Temperature a. Operating Environmental limitsRelative humidity Effective altitude sea level a. Operating Shock and vibrationShock Recommended mounting Vibration a. Operating-normalAir cleanliness AcousticsCorrosive environment Mounting configuration dimensions Mechanical specificationsPurpose About FipsValidation Program Seagate Enterprise SEDExample of Fips tamper evidence labels Admin SP Controlled accessAbout self-encrypting drives Data encryptionRandom number generator RNG Authenticated firmware downloadDrive locking Data bandsSupported commands Power requirementsSanitize Cryptographic Erase RevertSPDefect and error management Drive internal defects/errorsDrive error recovery procedures SAS system errors Background Media Scan Media Pre-ScanDeferred Auto-Reallocation Idle Read After Write Setting and determining the current Type LevelProtection Information PI Levels of PIIdentifying a Protection Information drive Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Mode Sense data Inquiry dataConstellation ES.1 inquiry data Page Mode Sense data changeable and default values for 2TB drives Mode Sense data changeable and default values for 1TB drives 3a 38 60 30 00 00 02 Miscellaneous operating features and conditions Miscellaneous featuresMiscellaneous status SAS physical interface Datum B Section C C Section a a Connector requirements Physical characteristicsElectrical description Pin descriptionsPower Signal characteristicsSAS transmitters and receivers Ready LED OutLED drive signal SAS-2 Specification ComplianceDifferential signals General interface characteristicsConstellation ES.1 SAS Product Manual, Rev. E Numerics IndexKCC Msid Mtbf See also cooling Page Constellation ES.1 SAS Product Manual, Rev. E Page Americas Seagate Technology LLC

ST2000NM0001, ST1000NM0041, ST500NM0001, ST2000NM0021, ST1000NM0021 specifications

Seagate is a renowned leader in data storage solutions, offering a wide array of hard disk drives (HDDs) suitable for various applications. Among their product lineup, the Seagate ST2000NM0041, ST500NM0021, ST500NM0041, ST1000NM0001, and ST1000NM0021 stand out as reliable options tailored for enterprise environments and general storage needs.

The Seagate ST2000NM0041 is a 2TB 7200 RPM drive designed for high-performance workloads in data centers. One of its key features is the use of the SATA III interface, providing data transfer speeds of up to 6 Gbps, ensuring quick access to data. This model supports advanced error recovery controls and features enhanced power management capabilities, which contribute to its reliable performance and energy efficiency.

Next, the ST500NM0021 and ST500NM0041 are both 500GB drives that cater to different consumer needs. The ST500NM0021 is a 5400 RPM drive, typically used in scenarios where lower power consumption is vital, such as in compact systems or external storage configurations. Its efficient design enables quieter operation, making it ideal for environments that require minimal noise. Conversely, the ST500NM0041 operates at a speed of 7200 RPM, making it suitable for more demanding applications that require swift read and write speeds. Both models utilize Serial ATA for connectivity, ensuring compatibility with a wide range of systems.

The ST1000NM0001 and ST1000NM0021 are 1TB drives that provide versatility across different platforms. Similar to their 500GB counterparts, the ST1000NM0001 features a 7200 RPM speed, optimizing performance for applications requiring faster data processing. In contrast, the ST1000NM0021 operates at 5400 RPM, designed for users prioritizing energy efficiency over speed, like in desktop and external storage solutions. Each of these drives supports advanced technologies such as Native Command Queuing (NCQ), which enhances performance by allowing multiple commands to be executed simultaneously.

Overall, the Seagate ST series hard drives offer flexible storage options for a variety of applications. With their robust features, including varied RPM speeds, power management, and compatibility with SATA connections, these drives cater to the needs of both consumer and enterprise markets, establishing Seagate as a trusted provider in the storage arena.
Top Page Image Contents