Seagate ST973402SS, ST9146802SS manual Standard features, Media description, Performance

Page 14

3.1Standard features

Savvio drives have the following standard features:

•Perpendicular recording technology

•1.5 / 3 Gbit Serial Attached SCSI (SAS) interface

•Integrated dual port SAS controller supporting the SCSI protocol

•Support for SAS expanders and fanout adapters

•Firmware downloadable using the SAS interface

•128 - deep task set (queue)

•Supports up to 32 initiators

•Jumperless configuration.

•User-selectable logical block size (512, 520, or 528 bytes per logical block).

•Industry standard SFF 2.5-inch dimensions

•Programmable logical block reallocation scheme

•Flawed logical block reallocation at format time

•Programmable auto write and read reallocation

•Reallocation of defects on command (Post Format)

•ECC maximum burst correction length of 320 bits

•No preventive maintenance or adjustments required

•Dedicated head landing zone

•Embedded servo design

•Automatic shipping lock

•Self diagnostics performed when power is applied to the drive

•Zone bit recording (ZBR)

•Vertical, horizontal, or top down mounting

•Dynamic spindle brake

•16 Mbyte data buffer (see Section 4.5).

•Drive Self Test (DST)

•Background Media Scan (BGMS)

•Idle Read After Write (IRAW)

•Power Save

3.2Media description

The media used on the drive has an aluminum substrate coated with a thin film magnetic material, overcoated with a proprietary protective layer for improved durability and environmental protection.

3.3Performance

•Programmable multi-segmentable cache buffer

•300 Mbytes/sec maximum instantaneous data transfers.

•10k RPM spindle. Average latency = 3.0 msec

•Background processing of queue

•Supports start and stop commands (spindle stops spinning)

•Adaptive seek velocity; improved seek performance

8

Savvio 10K.2 SAS Product Manual, Rev. D

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Savvio 10K.2 SAS ST9146802SS ST973402SSPage Contents Seagate Technology support services Defect and error managementInstallation Interface requirementsList of Figures Savvio 10K.2 SAS disc drivePage Scope Savvio 10K.2 SAS disc driveSavvio 10K.2 SAS Product Manual, Rev. D Electromagnetic compatibility Applicable standards and reference documentationStandards Electromagnetic susceptibilityAustralian C-Tick Electromagnetic complianceElectromagnetic compliance for the European Union Korean MICReference documents European Union Restriction of Hazardous Substances RoHSSavvio 10K.2 SAS Product Manual, Rev. D General description Performance Standard featuresMedia description Formatted capacities Factory-installed accessoriesReliability Programmable drive capacityFactory-installed options Seek performance characteristics Performance characteristicsInternal drive characteristics Access timeFormat command execution time for 512-byte sectors minutes General performance characteristicsCache operation Start/stop timePrefetch/multi-segmented cache control Caching write data Prefetch operationPage Savvio 10K.2 SAS Product Manual, Rev. D Recoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenancePerformance impact 4 S.M.A.R.TControlling S.M.A.R.T MillisecondsPredictive failures Reporting controlDetermining rate Thermal monitorDST failure definition Temperature Log Page 0Dh Parameter Code DescriptionDrive Self Test DST ImplementationShort and extended tests State of the drive prior to testingInvoking DST Short test Function Code 001bAbort Product warrantyLog page entries ShippingProduct repair and return information DC power requirements Physical/electrical specificationsAC power requirements ST9146802SS DC power requirementsST973402SS Gbit mode Amps ST973402SS DC power requirementsGeneral DC power requirement notes Current profiles Power sequencingConducted noise immunity ST973402SS current profile ST973402SS in 3 Gbit operation Power dissipationST9146802SS in 3 Gbit operation Temperature Environmental limitsShock and vibration Relative humidityEffective altitude sea level ShockPackage size Packaged/product weight Drop height Recommended mountingCorrosive environment Air cleanlinessVibration Acoustics Mechanical specifications Mounting configuration dimensionsSavvio 10K.2 SAS Product Manual, Rev. D Drive error recovery procedures Defect and error managementDrive internal defects/errors Page SAS system errors Background Media ScanIdle Read After Write Media Pre-ScanDeferred Auto-Reallocation Installation Drive orientationCooling Air flowDrive mounting GroundingSavvio 10K.2 SAS Product Manual, Rev. D SAS features Interface requirementsDual port support Command name Command code Supported Scsi commands supportedCommands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Savvio inquiry data Mode Sense dataInquiry data Bytes Data hexPage Mode Data Header 08 8b b9 98 00 00 02 Supported Feature or condition Miscellaneous operating features and conditionsMiscellaneous features Miscellaneous statusSAS physical interface Datum B Section C C Section a a Electrical description Physical characteristicsConnector requirements Pin descriptionsSAS transmitters and receivers Signal characteristicsPower Ready LED OutGeneral interface characteristics LED drive signalDifferential signals Eye masks Eye masks overviewReceive eye mask Jitter tolerance masksJitter Peak-toSinusoidal Frequency in kHzTransmitter signal characteristics Signal characteristica Units GbpsMaximum allowable jitter Receiver signal characteristicsSignal characteristic Units Gbps Gbps m, n Deterministic jitterqCompliant jitter test pattern Cjtpat Impedance specificationsReceiver jitter tolerance Impedance requirements Sheet 1Electrical TxRx connections Transmitter characteristicsImpedance requirements Sheet 2 = -5,437dB Tctf Receiver characteristics ISI loss example at 1.5 GbpsPresales Support Seagate Technology support servicesInternet Technical SupportData Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Index NumericsPage SAS See also cooling Page Seagate Technology LLC
Related manuals
Manual 90 pages 13.54 Kb

ST973402SS, ST9146802SS specifications

The Seagate ST973402SS and ST9146802SS are high-performance, enterprise-grade hard drives designed to meet the demanding needs of data-intensive applications. These drives are part of Seagate's Savvio and Barracuda product lines, aimed specifically at businesses and institutions requiring reliability, speed, and efficiency in storage solutions.

The ST973402SS is a 73GB, 2.5-inch hard drive, while the ST9146802SS offers a larger capacity of 146GB. Both models utilize a 10,000 RPM spindle speed, which significantly enhances their ability to handle fast data read and write operations. This speed ensures reduced latency and improved overall performance, making them ideal for environments where rapid access to data is crucial.

One of the standout features of these drives is their support for Serial Attached SCSI (SAS) interface. SAS technology provides a point-to-point connection, which allows for increased data transfer rates compared to traditional SATA drives. The ST973402SS and ST9146802SS are capable of transferring data at speeds of up to 600 MB/s, facilitating efficient data transfers in enterprise systems.

In terms of reliability, both models offer advanced features designed to improve data integrity and durability. They are built to withstand high workloads, with an annualized workload rate of up to 550 TB per year. This makes them well-suited for applications like databases and transactional storage, where sustained performance is required. Additionally, the drives feature Seagate’s PowerFit technology, which optimizes performance while minimizing power consumption.

To enhance data security, the drives come equipped with self-encrypting technology, ensuring that sensitive data is protected through hardware-based encryption. This is particularly important in environments where data breaches can lead to significant operational impacts.

The drives are also designed to operate efficiently in terms of thermal management, featuring robust heat dissipation capabilities. This helps to maintain optimal performance levels while prolonging the lifespan of the drives.

Overall, the Seagate ST973402SS and ST9146802SS are robust and reliable hard drives that cater to the needs of enterprise environments, combining high capacity, exceptional speed, advanced security features, and energy efficiency to help businesses maintain and manage large volumes of data effectively. With their proven performance and innovative technologies, these drives are well-equipped to support a wide range of applications in modern data centers.
Top Page Image Contents