Seagate ST9146802SS LED drive signal, Differential signals, General interface characteristics

Page 67

Table 24: Ready LED Out conditions

Normal command activity

LED status

 

 

Format in progress, each cylinder change

Toggles on/off

 

 

The Ready LED Out signal is designed to pull down the cathode of an LED. The anode is attached to the proper +3.3 volt supply through an appropriate current limiting resistor. The LED and the current limiting resis- tor are external to the drive. See Table 25 for the output characteristics of the LED drive signals.

Table 25:

LED drive signal

 

 

 

 

 

State

 

Test condition

Output voltage

 

 

 

 

LED off, high

 

0 V ≤ VOH ≤ 3.6 V

-100 µA < IOH < 100 µA

 

 

 

 

LED on, low

 

IOL = 15 mA

0 ≤ VOL ≤ 0.225 V

 

 

 

 

9.5.2Differential signals

The drive SAS differential signals comply with the intra-enclosure (internal connector) requirements of the SAS standard.

Table 26 defines the general interface characteristics.

Table 26: General interface characteristics

Characteristic

Units

1.5 Gbps

3.0 Gbps

 

 

 

 

Bit rate (nominal)

Mbaud

1,500

3,000

 

 

 

 

Unit interval (UI)(nominal)

ps

666.6

333.3

 

 

 

 

Impedance (nominal, differential )

ohm

100

100

 

 

 

 

Transmitter transients, maximum

V

± 1.2

± 1.2

 

 

 

 

Receiver transients, maximum

V

± 1.2

± 1.2

 

 

 

 

9.5.2.1Eye masks

9.5.2.1.1Eye masks overview

The eye masks are graphical representations of the voltage and point. The time values between X1 and (1 - X1) cover all but 10-12of the total jitter population has a range of ± 7 standard deviations.

time limits on the signal at the compliance of the jitter population. The random content

Savvio 10K.2 SAS Product Manual, Rev. D

61

Page 66 Page 68
Image 67
Page 66 Page 68
Contents ST9146802SS ST973402SS Savvio 10K.2 SASPage Contents Interface requirements Defect and error managementInstallation Seagate Technology support servicesSavvio 10K.2 SAS disc drive List of FiguresPage Savvio 10K.2 SAS disc drive ScopeSavvio 10K.2 SAS Product Manual, Rev. D Electromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityKorean MIC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickEuropean Union Restriction of Hazardous Substances RoHS Reference documentsSavvio 10K.2 SAS Product Manual, Rev. D General description Media description Standard featuresPerformance Programmable drive capacity Factory-installed accessoriesReliability Formatted capacitiesFactory-installed options Access time Performance characteristicsInternal drive characteristics Seek performance characteristicsGeneral performance characteristics Format command execution time for 512-byte sectors minutesPrefetch/multi-segmented cache control Start/stop timeCache operation Prefetch operation Caching write dataPage Savvio 10K.2 SAS Product Manual, Rev. D Unrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsMilliseconds 4 S.M.A.R.TControlling S.M.A.R.T Performance impactThermal monitor Reporting controlDetermining rate Predictive failuresImplementation Temperature Log Page 0Dh Parameter Code DescriptionDrive Self Test DST DST failure definitionShort test Function Code 001b State of the drive prior to testingInvoking DST Short and extended testsShipping Product warrantyLog page entries AbortProduct repair and return information ST9146802SS DC power requirements Physical/electrical specificationsAC power requirements DC power requirementsGeneral DC power requirement notes ST973402SS DC power requirementsST973402SS Gbit mode Amps Conducted noise immunity Power sequencingCurrent profiles ST973402SS current profile ST9146802SS in 3 Gbit operation Power dissipationST973402SS in 3 Gbit operation Environmental limits TemperatureShock Relative humidityEffective altitude sea level Shock and vibrationRecommended mounting Package size Packaged/product weight Drop heightVibration Air cleanlinessCorrosive environment Acoustics Mounting configuration dimensions Mechanical specificationsSavvio 10K.2 SAS Product Manual, Rev. D Drive internal defects/errors Defect and error managementDrive error recovery procedures Page Background Media Scan SAS system errorsDeferred Auto-Reallocation Media Pre-ScanIdle Read After Write Drive orientation InstallationAir flow CoolingGrounding Drive mountingSavvio 10K.2 SAS Product Manual, Rev. D Interface requirements SAS featuresDual port support Commands supported by Savvio SAS family drive Scsi commands supportedCommand name Command code Supported Commands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Bytes Data hex Mode Sense dataInquiry data Savvio inquiry dataPage Mode Data Header 08 8b b9 98 00 00 02 Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features Supported Feature or conditionSAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out Signal characteristicsPower SAS transmitters and receiversEye masks Eye masks overview LED drive signalDifferential signals General interface characteristicsJitter tolerance masks Receive eye maskFrequency in kHz Peak-toSinusoidal JitterSignal characteristica Units Gbps Transmitter signal characteristicsGbps m, n Deterministic jitterq Receiver signal characteristicsSignal characteristic Units Gbps Maximum allowable jitterImpedance requirements Sheet 1 Impedance specificationsReceiver jitter tolerance Compliant jitter test pattern CjtpatImpedance requirements Sheet 2 Transmitter characteristicsElectrical TxRx connections = -5,437dB Tctf ISI loss example at 1.5 Gbps Receiver characteristicsTechnical Support Seagate Technology support servicesInternet Presales SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Numerics IndexPage SAS See also cooling Page Seagate Technology LLC
Related manuals
Manual 90 pages 13.54 Kb

ST973402SS, ST9146802SS specifications

The Seagate ST973402SS and ST9146802SS are high-performance, enterprise-grade hard drives designed to meet the demanding needs of data-intensive applications. These drives are part of Seagate's Savvio and Barracuda product lines, aimed specifically at businesses and institutions requiring reliability, speed, and efficiency in storage solutions.

The ST973402SS is a 73GB, 2.5-inch hard drive, while the ST9146802SS offers a larger capacity of 146GB. Both models utilize a 10,000 RPM spindle speed, which significantly enhances their ability to handle fast data read and write operations. This speed ensures reduced latency and improved overall performance, making them ideal for environments where rapid access to data is crucial.

One of the standout features of these drives is their support for Serial Attached SCSI (SAS) interface. SAS technology provides a point-to-point connection, which allows for increased data transfer rates compared to traditional SATA drives. The ST973402SS and ST9146802SS are capable of transferring data at speeds of up to 600 MB/s, facilitating efficient data transfers in enterprise systems.

In terms of reliability, both models offer advanced features designed to improve data integrity and durability. They are built to withstand high workloads, with an annualized workload rate of up to 550 TB per year. This makes them well-suited for applications like databases and transactional storage, where sustained performance is required. Additionally, the drives feature Seagate’s PowerFit technology, which optimizes performance while minimizing power consumption.

To enhance data security, the drives come equipped with self-encrypting technology, ensuring that sensitive data is protected through hardware-based encryption. This is particularly important in environments where data breaches can lead to significant operational impacts.

The drives are also designed to operate efficiently in terms of thermal management, featuring robust heat dissipation capabilities. This helps to maintain optimal performance levels while prolonging the lifespan of the drives.

Overall, the Seagate ST973402SS and ST9146802SS are robust and reliable hard drives that cater to the needs of enterprise environments, combining high capacity, exceptional speed, advanced security features, and energy efficiency to help businesses maintain and manage large volumes of data effectively. With their proven performance and innovative technologies, these drives are well-equipped to support a wide range of applications in modern data centers.
Top Page Image Contents