Seagate ST973402SS, ST9146802SS manual

Page 58

On drives requiring unique saved values, the required unique saved values are stored into the saved val- ues storage location on the media prior to shipping the drive. Some drives may have unique firmware with unique default values also.

On standard OEM drives, the saved values are taken from the default values list and stored into the saved values storage location on the media prior to shipping.

3.Current values

Current values are volatile values being used by the drive to control its operation. A Mode Select command can be used to change the values identified as changeable values. Originally, current values are installed from saved or default values after a power on reset, hard reset, or Bus Device Reset message.

4.Changeable values

Changeable values form a bit mask, stored in nonvolatile memory, that dictates which of the current values and saved values can be changed by a Mode Select command. A one (1) indicates the value can be changed. A zero (0) indicates the value is not changeable. For example, in Table 19, refer to Mode page 81, in the row entitled “CHG.” These are hex numbers representing the changeable values for Mode page

81.Note in columns 5 and 6 (bytes 04 and 05), there is 00h which indicates that in bytes 04 and 05 none of the bits are changeable. Note also that bytes 06, 07, 09, 10, and 11 are not changeable, because those fields are all zeros. In byte 02, hex value FF equates to the binary pattern 11111111. If there is a zero in any bit position in the field, it means that bit is not changeable. Since all of the bits in byte 02 are ones, all of these bits are changeable.

The changeable values list can only be changed by downloading new firmware into the flash E-PROM.

Note. Because there are often several different versions of drive control firmware in the total population of drives in the field, the Mode Sense values given in the following tables may not exactly match those of some drives.

The following tables list the values of the data bytes returned by the drive in response to the Mode Sense com- mand pages for SCSI implementation (see the SAS Interface Manual).

DEF = Default value. Standard OEM drives are shipped configured this way.

CHG = Changeable bits; indicates if default value is changeable.

52

Savvio 10K.2 SAS Product Manual, Rev. D

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Savvio 10K.2 SAS ST9146802SS ST973402SSPage Contents Seagate Technology support services Defect and error managementInstallation Interface requirementsList of Figures Savvio 10K.2 SAS disc drivePage Scope Savvio 10K.2 SAS disc driveSavvio 10K.2 SAS Product Manual, Rev. D Electromagnetic compatibility Applicable standards and reference documentationStandards Electromagnetic susceptibilityAustralian C-Tick Electromagnetic complianceElectromagnetic compliance for the European Union Korean MICReference documents European Union Restriction of Hazardous Substances RoHSSavvio 10K.2 SAS Product Manual, Rev. D General description Media description Standard featuresPerformance Formatted capacities Factory-installed accessoriesReliability Programmable drive capacityFactory-installed options Seek performance characteristics Performance characteristicsInternal drive characteristics Access timeFormat command execution time for 512-byte sectors minutes General performance characteristicsPrefetch/multi-segmented cache control Start/stop timeCache operation Caching write data Prefetch operationPage Savvio 10K.2 SAS Product Manual, Rev. D Recoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenancePerformance impact 4 S.M.A.R.TControlling S.M.A.R.T MillisecondsPredictive failures Reporting controlDetermining rate Thermal monitorDST failure definition Temperature Log Page 0Dh Parameter Code DescriptionDrive Self Test DST ImplementationShort and extended tests State of the drive prior to testingInvoking DST Short test Function Code 001bAbort Product warrantyLog page entries ShippingProduct repair and return information DC power requirements Physical/electrical specificationsAC power requirements ST9146802SS DC power requirementsGeneral DC power requirement notes ST973402SS DC power requirementsST973402SS Gbit mode Amps Conducted noise immunity Power sequencingCurrent profiles ST973402SS current profile ST9146802SS in 3 Gbit operation Power dissipationST973402SS in 3 Gbit operation Temperature Environmental limitsShock and vibration Relative humidityEffective altitude sea level ShockPackage size Packaged/product weight Drop height Recommended mountingVibration Air cleanlinessCorrosive environment Acoustics Mechanical specifications Mounting configuration dimensionsSavvio 10K.2 SAS Product Manual, Rev. D Drive internal defects/errors Defect and error managementDrive error recovery procedures Page SAS system errors Background Media ScanDeferred Auto-Reallocation Media Pre-ScanIdle Read After Write Installation Drive orientationCooling Air flowDrive mounting GroundingSavvio 10K.2 SAS Product Manual, Rev. D SAS features Interface requirementsDual port support Commands supported by Savvio SAS family drive Scsi commands supportedCommand name Command code Supported Commands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Savvio inquiry data Mode Sense dataInquiry data Bytes Data hexPage Mode Data Header 08 8b b9 98 00 00 02 Supported Feature or condition Miscellaneous operating features and conditionsMiscellaneous features Miscellaneous statusSAS physical interface Datum B Section C C Section a a Electrical description Physical characteristicsConnector requirements Pin descriptionsSAS transmitters and receivers Signal characteristicsPower Ready LED OutGeneral interface characteristics LED drive signalDifferential signals Eye masks Eye masks overviewReceive eye mask Jitter tolerance masksJitter Peak-toSinusoidal Frequency in kHzTransmitter signal characteristics Signal characteristica Units GbpsMaximum allowable jitter Receiver signal characteristicsSignal characteristic Units Gbps Gbps m, n Deterministic jitterqCompliant jitter test pattern Cjtpat Impedance specificationsReceiver jitter tolerance Impedance requirements Sheet 1Impedance requirements Sheet 2 Transmitter characteristicsElectrical TxRx connections = -5,437dB Tctf Receiver characteristics ISI loss example at 1.5 GbpsPresales Support Seagate Technology support servicesInternet Technical SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Index NumericsPage SAS See also cooling Page Seagate Technology LLC
Related manuals
Manual 90 pages 13.54 Kb

ST973402SS, ST9146802SS specifications

The Seagate ST973402SS and ST9146802SS are high-performance, enterprise-grade hard drives designed to meet the demanding needs of data-intensive applications. These drives are part of Seagate's Savvio and Barracuda product lines, aimed specifically at businesses and institutions requiring reliability, speed, and efficiency in storage solutions.

The ST973402SS is a 73GB, 2.5-inch hard drive, while the ST9146802SS offers a larger capacity of 146GB. Both models utilize a 10,000 RPM spindle speed, which significantly enhances their ability to handle fast data read and write operations. This speed ensures reduced latency and improved overall performance, making them ideal for environments where rapid access to data is crucial.

One of the standout features of these drives is their support for Serial Attached SCSI (SAS) interface. SAS technology provides a point-to-point connection, which allows for increased data transfer rates compared to traditional SATA drives. The ST973402SS and ST9146802SS are capable of transferring data at speeds of up to 600 MB/s, facilitating efficient data transfers in enterprise systems.

In terms of reliability, both models offer advanced features designed to improve data integrity and durability. They are built to withstand high workloads, with an annualized workload rate of up to 550 TB per year. This makes them well-suited for applications like databases and transactional storage, where sustained performance is required. Additionally, the drives feature Seagate’s PowerFit technology, which optimizes performance while minimizing power consumption.

To enhance data security, the drives come equipped with self-encrypting technology, ensuring that sensitive data is protected through hardware-based encryption. This is particularly important in environments where data breaches can lead to significant operational impacts.

The drives are also designed to operate efficiently in terms of thermal management, featuring robust heat dissipation capabilities. This helps to maintain optimal performance levels while prolonging the lifespan of the drives.

Overall, the Seagate ST973402SS and ST9146802SS are robust and reliable hard drives that cater to the needs of enterprise environments, combining high capacity, exceptional speed, advanced security features, and energy efficiency to help businesses maintain and manage large volumes of data effectively. With their proven performance and innovative technologies, these drives are well-equipped to support a wide range of applications in modern data centers.
Top Page Image Contents