Seagate ST9146802SS, ST973402SS manual Vibration, Air cleanliness, Corrosive environment

Page 39

6.4.4.2Vibration

a. Operating—normal

The drive as installed for normal operation, shall comply with the complete specified performance while subjected to continuous vibration not exceeding

1-500 Hz @ 0.5 G (zero to peak)

Vibration may be applied in the X, Y, or Z axis.

Operating normal translational random flat profile

10 - 400 Hz

0.4 GRMS

b.Operating—abnormal

Equipment as installed for normal operation shall not incur physical damage while subjected to periodic vibration not exceeding:

15 minutes of duration at major resonant frequency 10-500 Hz @ 1.5 G (X, Y, or Z axis)

Vibration occurring at these levels may degrade operational performance during the abnormal vibration period. Specified operational performance will continue when normal operating vibration levels are resumed. This assumes system recovery routines are available.

Operating abnormal translational random flat profile

10 - 500 Hz

1.2 GRMS

c.Non-operating

The limits of non-operating vibration shall apply to all conditions of handling and transportation. This includes both isolated drives and integrated drives.

The drive shall not incur physical damage or degraded performance as a result of continuous vibration not exceeding

5-22 Hz @ 0.040 inches (1.02 mm) displacement (zero to peak)

20-500 Hz @ 3.0 G (zero to peak)

Vibration may be applied in the X, Y, or Z axis.

Non-operating translational random flat profile

10 - 500 Hz

1.2 GRMS

6.4.5Air cleanliness

The drive is designed to operate in a typical office environment with minimal environmental control.

6.4.6Corrosive environment

Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated testing cannot duplicate every potential application environment.

Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corro- sive chemicals as electronic drive component reliability can be affected by the installation environment. The sil- ver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulca- nized rubber, that can outgas corrosive compounds sshould be minimized or eliminated. The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.

Savvio 10K.2 SAS Product Manual, Rev. D

33

Page 38 Page 40
Image 39
Page 38 Page 40
Contents ST9146802SS ST973402SS Savvio 10K.2 SASPage Contents Interface requirements Defect and error managementInstallation Seagate Technology support servicesSavvio 10K.2 SAS disc drive List of FiguresPage Savvio 10K.2 SAS disc drive ScopeSavvio 10K.2 SAS Product Manual, Rev. D Electromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityKorean MIC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickEuropean Union Restriction of Hazardous Substances RoHS Reference documentsSavvio 10K.2 SAS Product Manual, Rev. D General description Standard features Media descriptionPerformance Programmable drive capacity Factory-installed accessoriesReliability Formatted capacitiesFactory-installed options Access time Performance characteristicsInternal drive characteristics Seek performance characteristicsGeneral performance characteristics Format command execution time for 512-byte sectors minutesStart/stop time Prefetch/multi-segmented cache controlCache operation Prefetch operation Caching write dataPage Savvio 10K.2 SAS Product Manual, Rev. D Unrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsMilliseconds 4 S.M.A.R.TControlling S.M.A.R.T Performance impactThermal monitor Reporting controlDetermining rate Predictive failuresImplementation Temperature Log Page 0Dh Parameter Code DescriptionDrive Self Test DST DST failure definitionShort test Function Code 001b State of the drive prior to testingInvoking DST Short and extended testsShipping Product warrantyLog page entries AbortProduct repair and return information ST9146802SS DC power requirements Physical/electrical specificationsAC power requirements DC power requirementsST973402SS DC power requirements General DC power requirement notesST973402SS Gbit mode Amps Power sequencing Conducted noise immunityCurrent profiles ST973402SS current profile Power dissipation ST9146802SS in 3 Gbit operationST973402SS in 3 Gbit operation Environmental limits TemperatureShock Relative humidityEffective altitude sea level Shock and vibrationRecommended mounting Package size Packaged/product weight Drop heightAir cleanliness VibrationCorrosive environment Acoustics Mounting configuration dimensions Mechanical specificationsSavvio 10K.2 SAS Product Manual, Rev. D Defect and error management Drive internal defects/errorsDrive error recovery procedures Page Background Media Scan SAS system errorsMedia Pre-Scan Deferred Auto-ReallocationIdle Read After Write Drive orientation InstallationAir flow CoolingGrounding Drive mountingSavvio 10K.2 SAS Product Manual, Rev. D Interface requirements SAS featuresDual port support Scsi commands supported Commands supported by Savvio SAS family driveCommand name Command code Supported Commands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Bytes Data hex Mode Sense dataInquiry data Savvio inquiry dataPage Mode Data Header 08 8b b9 98 00 00 02 Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features Supported Feature or conditionSAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out Signal characteristicsPower SAS transmitters and receiversEye masks Eye masks overview LED drive signalDifferential signals General interface characteristicsJitter tolerance masks Receive eye maskFrequency in kHz Peak-toSinusoidal JitterSignal characteristica Units Gbps Transmitter signal characteristicsGbps m, n Deterministic jitterq Receiver signal characteristicsSignal characteristic Units Gbps Maximum allowable jitterImpedance requirements Sheet 1 Impedance specificationsReceiver jitter tolerance Compliant jitter test pattern CjtpatTransmitter characteristics Impedance requirements Sheet 2Electrical TxRx connections = -5,437dB Tctf ISI loss example at 1.5 Gbps Receiver characteristicsTechnical Support Seagate Technology support servicesInternet Presales SupportWarranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Numerics IndexPage SAS See also cooling Page Seagate Technology LLC
Related manuals
Manual 90 pages 13.54 Kb

ST973402SS, ST9146802SS specifications

The Seagate ST973402SS and ST9146802SS are high-performance, enterprise-grade hard drives designed to meet the demanding needs of data-intensive applications. These drives are part of Seagate's Savvio and Barracuda product lines, aimed specifically at businesses and institutions requiring reliability, speed, and efficiency in storage solutions.

The ST973402SS is a 73GB, 2.5-inch hard drive, while the ST9146802SS offers a larger capacity of 146GB. Both models utilize a 10,000 RPM spindle speed, which significantly enhances their ability to handle fast data read and write operations. This speed ensures reduced latency and improved overall performance, making them ideal for environments where rapid access to data is crucial.

One of the standout features of these drives is their support for Serial Attached SCSI (SAS) interface. SAS technology provides a point-to-point connection, which allows for increased data transfer rates compared to traditional SATA drives. The ST973402SS and ST9146802SS are capable of transferring data at speeds of up to 600 MB/s, facilitating efficient data transfers in enterprise systems.

In terms of reliability, both models offer advanced features designed to improve data integrity and durability. They are built to withstand high workloads, with an annualized workload rate of up to 550 TB per year. This makes them well-suited for applications like databases and transactional storage, where sustained performance is required. Additionally, the drives feature Seagate’s PowerFit technology, which optimizes performance while minimizing power consumption.

To enhance data security, the drives come equipped with self-encrypting technology, ensuring that sensitive data is protected through hardware-based encryption. This is particularly important in environments where data breaches can lead to significant operational impacts.

The drives are also designed to operate efficiently in terms of thermal management, featuring robust heat dissipation capabilities. This helps to maintain optimal performance levels while prolonging the lifespan of the drives.

Overall, the Seagate ST973402SS and ST9146802SS are robust and reliable hard drives that cater to the needs of enterprise environments, combining high capacity, exceptional speed, advanced security features, and energy efficiency to help businesses maintain and manage large volumes of data effectively. With their proven performance and innovative technologies, these drives are well-equipped to support a wide range of applications in modern data centers.
Top Page Image Contents