Seagate Lyrion Series manual Nonoperating random vibration profile, Corrosive environment

Page 20

2.8.6.4Nonoperating random vibration

The test consists of 15 minutes of random vibration using the power spectral density (PSD) levels specified in the table below. The vibration test level is 3.01 Gs RMS. The drive does not incur any physical damage when subsequently put into operation.

Table 5: Nonoperating random vibration profile.

Frequency (Hz)

G2/Hz

 

 

2.5

1.0 x E-03

 

 

5

3.0 x E-02

 

 

40

1.8 x E-02

 

 

500

1.8 x E-02

 

 

2.8.7Corrosive environment

Seagate electronic drive components pass accelerated corrosion testing equivalent to ten years of exposure to light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated testing cannot duplicate every potential application environment.

Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corro- sive chemicals as electronic drive component reliability can be affected by the installation environment. The sil- ver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95 percent. Materials used in cabinet fabrication, such as vulcanized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.

14

Lyrion CE-ATA Product Manual, Rev. A

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Lyrion Series CE-ATA ST760211CA ST730212CARevision history Revision DateContents Lyrion CE-ATA Product Manual, Rev. a List of Figures Lyrion CE-ATA Product Manual, Rev. a Introduction Lyrion Series CE-ATA interface disc driveDisclaimer Drive careDrive specifications SpecificationsDrive specification ST760211CA ST730212CA OverviewSpecifications Default logical geometry LBA mode addressingFormatted capacity Model Cylinders Heads SectorsPhysical characteristics Technology SpecificationRecording and interface technology Time to readyPower specifications Typical current profile DC powerPower Consumption at Average W Conducted noise Voltage tolerance Voltage tolerance including noisePower-management modes Active modeStandby/Sleep mode Power modes Heads Spindle BufferEnvironmental specifications Shock Operating shockNonoperating shock VibrationOperating sweep sine vibration Operating random vibrationOperating random vibration profile Nonoperating sweep sine vibrationCorrosive environment Nonoperating random vibrationNonoperating random vibration profile Acoustics Electromagnetic immunityDrive level acoustics Electromagnetic immunityMeasurement type Specification ReliabilitySafety certification Agency certificationElectromagnetic compatibility Korean RRLChina Restriction of Hazardous Substances RoHS Directive FCC verificationPage Lyrion CE-ATA Product Manual, Rev. a Configuring and mounting the drive Handling and static discharge precautionsPage Drive installation Lyrion Series mechanical dimensions-top, side and end viewLyrion Series FPC dimensions Mounting considerationsInterface signals and connector pins Way ZIF CE-ATA interface connector signalsPin number Signal Name Definition Interface descriptionSupported command set and features MMC command setReduced ATA command set Supported commands Command Index Command Name Command DescriptionWord Description Value Identify Device commandIdentify Device commands Byte Name Detailed description Address Status and Control RegistersIndex Byte Address Name Description Seagate Technology support services InternetPresales Support Technical SupportData Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Index Page Page Seagate Technology LLC

Lyrion Series specifications

The Seagate Lyrion Series is an innovative line of storage solutions designed to meet the high-performance demands of data-intensive applications. As data continues to proliferate across industries, the need for reliable, efficient, and scalable storage solutions becomes paramount. The Lyrion Series addresses this need by offering advanced technologies and characteristics that set it apart in the competitive storage market.

One of the standout features of the Lyrion Series is its impressive speed and performance. Leveraging cutting-edge Solid-State Drive (SSD) technology, these drives significantly reduce latency and enhance data access speeds compared to traditional Hard Disk Drives (HDDs). This performance boost is especially beneficial for applications that require rapid data retrieval and processing, such as virtualization, big data analytics, and real-time data processing.

Another key characteristic of the Seagate Lyrion Series is its capacity for high scalability. These drives are designed to accommodate the growing demands of modern storage environments, making them suitable for enterprises with evolving data needs. The Lyrion Series provides a range of capacities, enabling businesses to scale their storage solutions seamlessly as their data requirements expand.

Furthermore, the Lyrion Series incorporates advanced security features, ensuring that sensitive data is protected against unauthorized access. With built-in encryption options, businesses can rest assured that their information remains secure while being stored or transmitted. This is particularly crucial in industries that handle confidential data, such as finance, healthcare, and government.

The durability of the Seagate Lyrion Series also deserves attention. Designed for longevity and reliability, these drives offer robust performance in demanding conditions. They are built to withstand operational stress and provide consistent performance over time, minimizing downtime and ensuring that critical data is always accessible.

In addition to these core features, the Lyrion Series is engineered for energy efficiency. By minimizing power consumption, these drives not only reduce operational costs but also contribute to a greener IT infrastructure. This focus on sustainability aligns with the increasing global emphasis on reducing carbon footprints and promoting environmentally friendly practices.

In summary, the Seagate Lyrion Series is a versatile and powerful storage solution that combines speed, scalability, security, durability, and energy efficiency. These characteristics make it an ideal choice for businesses across various sectors looking to manage their data more effectively. As the digital landscape continues to evolve, the Lyrion Series stands as a testament to Seagate’s commitment to innovation and excellence in data storage technology.
Top Page Image Contents