Seagate ST31000640SSIM manual Signal characteristics, SAS transmitters and receivers, Power

Page 65

9.4.6SAS transmitters and receivers

A typical SAS differential copper transmitter and receiver pair is shown in Figure 15. The receiver is AC cou- pling to eliminate ground shift noise.

		TX
	Transmitter	Differential
	Transmitter	Transfer Medium
	100	Transfer Medium
	100
		TY

Figure 15. SAS transmitters and receivers

.01

.01

RX

Receiver 100

RY

9.4.7Power

The drive receives power (+5 volts and +12 volts) through the SAS device connector.

Three +12 volt pins provide power to the drive, 2 short and 1 long. The current return for the +12 volt power supply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Three +5 volt pins provide power to the drive, 2 short and 1 long. The current return for the +5 volt power sup- ply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Current to the drive through the long power pins may be limited by the system to reduce inrush current to the drive during hot plugging.

9.5Signal characteristics

This section describes the electrical signal characteristics of the drive’s input and output signals. See Table 12 for signal type and signal name information.

9.5.1Ready LED Out

The Ready LED Out signal is driven by the drive as indicated in Table 13.

Table 13: Ready LED Out conditions

Normal command activity		LED status

Ready LED Meaning bit mode page 19h	0		1

Spun down and no activity	Off		Off

Spun down and activity (command executing)	On		On

Spun up and no activity	On		Off

Spun up and activity (command executing)	Off		On

Spinning up or down		Blinks steadily
	(50% on and 50% off, 0.5 seconds on and off for 0.5 seconds)

Format in progress, each cylinder change		Toggles on/off

Barracuda ES.2 SAS Product Manual, Rev. G

59

Image 65

Contents ST31000640SS ST3750630SS ST3500620SS Barracuda ES.2 SASPage Reliability specifications Performance characteristicsPhysical/electrical specifications General descriptionInterface requirements Defect and error managementInstallation Seagate Technology Support Services Barracuda ES.2 SAS Product Manual, Rev Scope Barracuda ES.2 SAS Product Manual, Rev. G Standards Standards, compliance and reference documentsElectromagnetic compatibility Electromagnetic susceptibilityCompliance Reference documents Barracuda ES.2 SAS Product Manual, Rev. G Barracuda ES.2 drive illustration General descriptionMedia description Standard featuresPerformance ReliabilityProgrammable drive capacity Factory-installed optionsFormatted capacities Barracuda ES.2 SAS Product Manual, Rev. G Internal drive characteristics Performance characteristicsAccess time Seek performanceStart/stop time Format command execution time minutesGeneral performance characteristics Caching write data Prefetch/multi-segmented cache controlCache operation Prefetch operation Error rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenanceControlling S.M.A.R.T 4 S.M.A.R.TPerformance impact Reporting controlThermal monitor Temperature Log Page 0DhPredictive failures DST failure definition State of the drive prior to testingImplementation Invoking DSTShort test Function Code 001b Product warrantyExtended test Function Code 010b Log page entriesProduct repair and return information ShippingBarracuda ES.2 SAS Product Manual, Rev. G AC power requirements Physical/electrical specificationsDC power requirements ST31000640SS DC power requirementsST3500620SS DC power requirements ST3750630SS DC power requirementsPower sequencing General DC power requirement notesConducted noise immunity Current profilesTypical ST31000640SS drive +5V and +12V current profiles Typical ST3500620SS drive +5V and +12V current profiles Power dissipationBarracuda ES.2 SAS Product Manual, Rev. G Environmental limits Temperature a. OperatingEffective altitude sea level a. Operating Relative humidityShock and vibration ShockPackage size Packaged/product weight Drop height Vibration a. Operating-normal Air cleanlinessAcoustics Corrosive environmentSee Section Barracuda ES.2 SAS Product Manual, Rev. G Physical dimensions Mechanical specificationsDrive error recovery procedures Defect and error managementDrive internal defects/errors 108.29 Media Pre-Scan SAS system errorsBackground Media Scan Idle Read After Write Deferred Auto-ReallocationDrive orientation InstallationAir flow CoolingGrounding Drive mountingBarracuda ES.2 SAS Product Manual, Rev. G Interface requirements SAS featuresDual port support Command name Command code Supported Scsi commands supportedCommands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Barracuda ES.2 SAS inquiry data Bytes Data hex Mode Sense dataInquiry data Page Mode Pages 2.1 ST31000640SS Mode Sense data2.2 ST3750630SS Mode Sense data 2.3 ST3500620SS Mode Sense data Miscellaneous features Miscellaneous operating features and conditionsSupported Feature or condition Miscellaneous statusSAS physical interface Datum B Connector requirements Physical characteristicsElectrical description Pin Signal name Signal typePin descriptions SAS pin descriptionsPower Signal characteristicsSAS transmitters and receivers Ready LED OutDifferential signals LED drive signalGeneral interface characteristics Eye masks Eye masks overviewJitter tolerance masks Receive eye maskAbsolute amplitude Normalized time in UISinusoidal Peak-toJitter Frequency in kHzSignal characteristica Units Gbps Transmitter signal characteristicsSignal characteristic Units Gbps Receiver signal characteristicsMaximum allowable jitter Gbps m, n Deterministic jitterqReceiver jitter tolerance Impedance specificationsCompliant jitter test pattern Cjtpat Impedance requirements Sheet 1Electrical TxRx connections Transmitter characteristicsImpedance requirements Sheet 2 = -5,437dB Shows the zero-length test load Receiver characteristics Barracuda ES.2 SAS Product Manual, Rev. G