Seagate ST31000640SSIM manual = -5,437dB

Page 73

A combination of a zero-length test load and the transmitter compliance transfer function (TCTF) test load methodology is used for the specification of transmitter characteristics. This methodology specifies the trans- mitter signal at the test points on the required test loads. The transmitter uses the same settings (e.g., pre- emphasis, voltage swing) with both the zero-length test load and the TCTF test load. The signal specifications at IR are met under each of these loading conditions.

The TCTF is the mathematical statement of the transfer function through which the transmitter shall be capable of producing acceptable signals as defined by a receive mask. The transmission magnitude response of the TCTF in dB is given by the following equation for 1.5 Gbps:

S21

= –20× log10( e) × ( ( 6, 5 × 10–6× f0, 5) + ( 2, 0 × 10–10× f) + ( 3, 3 × 10–20× f2) ) dB

for 50 MHz < f < 1.5 GHz, and:

S21

= –5,437dB

for 1.5 GHz < f < 5.0 GHz, where:

a) f is the signal frequency in hertz.

The transmission magnitude response of the TCTF in dB is given by the following equation for 3.0 Gbps:

S21 = –20× log10( e) × ( ( 6, 5 × 10–6× f0, 5) + ( 2, 0 × 10–10× f) + ( 3, 3 × 10–20× f2) ) dB

for 50 MHz < f < 3.0 GHz, and:

S21

= –10,884dB

for 3.0 GHz < f < 5.0 GHz,

where f is the signal frequency in hertz.

The TCTF is used to specify the requirements on transmitters that may or may not incorporate pre-emphasis or other forms of compensation. A compliance interconnect is any physical interconnect with loss equal to or greater than that of the TCTF at the above frequencies that also meets the ISI loss requirements shown in fig- ure 21 and figure 22.

Compliance with the TCTF test load requirement is verified by measuring the signal produced by the transmit- ter through a physical compliance interconnect attached to the transmitter.

Compliance with the zero-length test load requirement verified by measurement made across a load equiva- lent to the zero-length load shown in figure 20.

For both test load cases, the transmitter delivers the output voltages and timing listed in table 17 at the desig- nated compliance points. The default mask is IR for intra-cabinet TxRx connections. The eye masks are shown in 9.5.2.1.

Figure 19 shows the compliance interconnect test load.

Tx+

TCTF

Tx-

10 nF

50 ohm

Probe

 

points

 

10 nF

50 ohm

SAS internal connector

Figure 19. Compliance interconnect test load

Barracuda ES.2 SAS Product Manual, Rev. G

67

Page 72 Page 74
Image 73
Page 72 Page 74
Contents ST31000640SS ST3750630SS ST3500620SS Barracuda ES.2 SASPage Reliability specifications Performance characteristicsPhysical/electrical specifications General descriptionInstallation Defect and error managementInterface requirements Seagate Technology Support Services Barracuda ES.2 SAS Product Manual, Rev Scope Barracuda ES.2 SAS Product Manual, Rev. G Standards Standards, compliance and reference documentsElectromagnetic compatibility Electromagnetic susceptibilityCompliance Reference documents Barracuda ES.2 SAS Product Manual, Rev. G Barracuda ES.2 drive illustration General descriptionMedia description Standard featuresPerformance ReliabilityFormatted capacities Factory-installed optionsProgrammable drive capacity Barracuda ES.2 SAS Product Manual, Rev. G Internal drive characteristics Performance characteristicsAccess time Seek performanceGeneral performance characteristics Format command execution time minutesStart/stop time Cache operation Prefetch/multi-segmented cache controlCaching write data Prefetch operation Error rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenanceControlling S.M.A.R.T 4 S.M.A.R.TPerformance impact Reporting controlPredictive failures Temperature Log Page 0DhThermal monitor DST failure definition State of the drive prior to testingImplementation Invoking DSTShort test Function Code 001b Product warrantyExtended test Function Code 010b Log page entriesProduct repair and return information ShippingBarracuda ES.2 SAS Product Manual, Rev. G AC power requirements Physical/electrical specificationsDC power requirements ST31000640SS DC power requirementsST3500620SS DC power requirements ST3750630SS DC power requirementsPower sequencing General DC power requirement notesConducted noise immunity Current profilesTypical ST31000640SS drive +5V and +12V current profiles Typical ST3500620SS drive +5V and +12V current profiles Power dissipationBarracuda ES.2 SAS Product Manual, Rev. G Environmental limits Temperature a. OperatingEffective altitude sea level a. Operating Relative humidityShock and vibration ShockPackage size Packaged/product weight Drop height Vibration a. Operating-normal Air cleanlinessAcoustics Corrosive environmentSee Section Barracuda ES.2 SAS Product Manual, Rev. G Physical dimensions Mechanical specificationsDrive internal defects/errors Defect and error managementDrive error recovery procedures 108.29 Background Media Scan SAS system errorsMedia Pre-Scan Idle Read After Write Deferred Auto-ReallocationDrive orientation InstallationAir flow CoolingGrounding Drive mountingBarracuda ES.2 SAS Product Manual, Rev. G Interface requirements SAS featuresDual port support Commands supported by Barracuda ES.2 SAS family drives Scsi commands supportedCommand name Command code Supported Commands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Inquiry data Mode Sense dataBarracuda ES.2 SAS inquiry data Bytes Data hex Page Mode Pages 2.1 ST31000640SS Mode Sense data2.2 ST3750630SS Mode Sense data 2.3 ST3500620SS Mode Sense data Miscellaneous features Miscellaneous operating features and conditionsSupported Feature or condition Miscellaneous statusSAS physical interface Datum B Connector requirements Physical characteristicsElectrical description Pin Signal name Signal typePin descriptions SAS pin descriptionsPower Signal characteristicsSAS transmitters and receivers Ready LED OutDifferential signals LED drive signalGeneral interface characteristics Eye masks Eye masks overviewJitter tolerance masks Receive eye maskAbsolute amplitude Normalized time in UISinusoidal Peak-toJitter Frequency in kHzSignal characteristica Units Gbps Transmitter signal characteristicsSignal characteristic Units Gbps Receiver signal characteristicsMaximum allowable jitter Gbps m, n Deterministic jitterqReceiver jitter tolerance Impedance specificationsCompliant jitter test pattern Cjtpat Impedance requirements Sheet 1Impedance requirements Sheet 2 Transmitter characteristicsElectrical TxRx connections = -5,437dB Shows the zero-length test load Receiver characteristics Barracuda ES.2 SAS Product Manual, Rev. G
Top Page Image Contents